Unex Flow Cell User manual

Pick Smarter. Pick Better. Pick UNEX.
ASSEMBLY INSTRUCTIONS
A Flow Cell modular unit starts with a framework of vertical Posts & horizontal Beams (Flow Cell Structure)
bolted together with 3/8"-16 hardware (included)—only one wrench size (9/16") is required.
This base structure plus Span-Track carton flow track and any of several optional features
complete the Flow Cell assembly.
Attach side Beams (2) to Posts (2) for each side of cell — one high, one low.
FlowCell with Tool Bar will have 2 longer posts at front. Note: Ensure foot
plates oriented in the same direction. If using rigid casters, align long
dimension of plates in direction cell is to roll.
1
Join the 2 sides by bolting on front
beams at discharge heights at front of
cell. For return lane front beam would
be at load height.
2
Bolt on rear beams for each level
approximately 1" higher per foot than
front beams. Recommended pitch is 1
inch for every 1 foot of rack depth.
3
Slip plastic End Caps onto posts.
4
UNEX MANUFACTURING, INC. www.unex.com/resources/video-library
50 Progress Place, Jackson, NJ 08527
800.695.SPAN (7726)
732-928-2800 • fax: [phone] • e-mail: [e-mail] • unex.com
FLOW CELL STRUCTURE
FLOW CELL OPTIONS (all necessary brackets and hardware are included)
(video instruction hyperlinks below in text)
NOTE: Before
attaching side Beams,
determine front &
rear Beam positions
(be sure to consider
pitch), since side
Beams cannot share
Post locations with
front & rear Beams.
CASTERS
Attach casters to
foot plates using
3/8" bolts. (provided)
http://www.youtube.com/watch?v=FmfHPMQroU4
WORKBENCH
Attach shelf brackets (2) to posts at desired height
using 3/8 bolts. Attach workbench, inserting 4
bolts from below.
http://www.youtube.com/watch?v=sJKyUwg0SmU
ADD-ON TRAY
Attach tray brackets to tray. Hang back of tray
over front beam. Bolt brackets to posts. Attach
full-length Label Holder to front surface of
Add-On Tray using two-sided tape (provided
on back side of Label Holder).
For detailed video installation instructions, please go to: www.unex.com/resources/video-library
OVERHEAD TOOL BAR
Attach brackets (2) at top of front posts using 3/8"
bolts. Attach tool bar strut channel with 2 bolts
inserted from below, and 2 strut nuts.
http://www.youtube.com/watch?v=6fNYzAxCfww

Pick Smarter. Pick Better. Pick UNEX.
INSTALLING SPAN-TRACK
FlowCell™ framework (vertical Posts & horizontal Beams) accepts Cell Span-Track
and High Profile Span-Track models.
Drop-in installation. Notched front end rests on beam.
Flat plate at rear wraps over beam.
UNEX MANUFACTURING, INC. www.unex.com/resources/video-library
50 Progress Place, Jackson, NJ 08527
800.695.SPAN (7726)
732-928-2800 • fax: [phone] • e-mail: [e-mail] • unex.com
CELL SPAN-TRACK (LANE OR BED)
Attach pre-punched Retainer Angles to front and rear beams (fig. 1)
using supplied tek screws. Position track on retainers and lock into
desired position with Lock Arm at load end of track (fig. 2).
Lock Arm can be positioned for track end flush with beam
or overhanging.
HIGH PROFILE & KNUCKLE SPAN-TRACK LANE
With Span-Track installed test pitch to ensure that products/totes
flow eectively. Adjust beams if necessary.
TEST PITCH
Knuckled end of track
must extend entirely
beyond beam
Figure 1
Figure 2
LOCKED
UNLOCKED
For detailed video installation instructions, please go to: www.unex.com/resources/video-library