Uni-Com PLA User manual

WARNING
Please carefully inspect the product before assembling. If you notice any apparent damage, call your carrier
claims agent and do not continue the installation until it has been reviewed. Please watch for pinch points.
Do not put your fingers between moveable parts. Do not tamper with or disassemble any spring loaded
parts. Before installing, make sure that the supporting surface will support five times the combined load of
the solution and the hardware. Never exceed the maximum load capacity. Please also layout all components
to ensure that you have all of the required parts before proceeding (see BOM list on following page). Use of
this product for anything other than its specified use may result in failure or personal injury. This product is
intended for indoor use only. We recommend using a qualified trades person for installation. Use an assistant
or lifting equipment to lift and position products.
For support, please call: [phone] or email: [e-mail]
Revised 24/02/22
01865 767676
[e-mail]
www.unicol.com
*Please check model specific details before installing*
Wall Arms – PLA & PLS – SSV & SRV
*Please check model specific details before installing*
Screen Size: 33-57” Guide Max. Weight: 30kg
Screen Size: 15-32” Guide Max. Weight: 20kg
PLS1X1
PL A1X1
SSV
SRV

2Revised 24/02/22
COMPONENTS
01865 767676
[e-mail]
www.unicol.com
INSTALLERS REQUIRED
1-2
# DESCRIPTION QTY
1SRV Single Swing Arm Complete 1
#TOOLS REQUIRED
13/16th Allen Key
2Pozidrive Screwdriver
317mm Spanner
4
5
21
# DESCRIPTION QTY
1SSV Double Swing Arm Complete 1
# DESCRIPTION QTY
1PLS Single Swing Arm 1
2PZX Universal Mount 1
# DESCRIPTION QTY
1PLA Double Swing Arm 1
2PZX Universal Mount
1
2
2
1

01865 767676
[e-mail]
www.unicol.com
3
Revised 24/02/22
STEP 1 – (PLS & PLA)
Using the 3 mounting holes in the back plate,
determine where you want to install your mount, mark
and fix into position using suitable anchors & screws.
Please consider cabling and wall fixings prior to
installation. Please check surface is capable of
supporting 5x the combined solutions weight.
STEP 2 – (PLS & PLA)
A separate universal mount (PZX) is provided to mount
your screen to the PLS or PLA. Separate instructions
are provided with each screen mount. Follow these to
mount your screen onto the mount backplate.
Fix the PZX backplate to the head of the PLS/PLA
using the M25 hex head screws provided.
STEP 3 – (PLS & PLA)
There is fine adjustment of the screen tilt angle using
the allen key provided to rotate the knurled adjuster on
the rear of the mount. Turn clockwise to tilt upwards.
STEP 4 – (PLS & PLA)
The screen can be levelled slightly by rotating the
screen clockwise or anticlockwise.
Cable up your screen using cable ties through the
holes in the arms. The PLA has extra tags on the elbow
of the first arm for this purpose.
PLS & PLA
11
162
285
240
120
PLS
PZX

4Revised 24/02/22
01865 767676
[e-mail]
www.unicol.com
STEP 1 – (SRV & SSV)
Using the 2 mounting holes in the back plate,
determine where you want to install your mount, mark
and fix into position using suitable anchors & screws.
Please consider cabling and wall fixings prior to
installation. Please check surface is capable of
supporting 5x the combined solutions weight.
STEP 2 – (SRV & SSV)
Fix your screen to the mounting plate shown above
with the appropriate screws . There are fixing holes for
VESA 100x100 and 100x200.
160
200
100
100
Ass--20007610-2.AI 1 23/02/2022 16:07:55
STEP 3 – (SRV & SSV)
There is fine adjustment of the screen tilt angle using
the knurled adjuster on the rear of the mount. Turn
clockwise to tilt upwards.
STEP 4 – (SRV & SSV)
The screen can be levelled slightly by rotating the
screen clockwise or anticlockwise.
Cable up your screen using cable ties through the
holes in the arms. The SSV has extra tags on the elbow
of the first arm for this purpose.
160
9
SRV & SSV