Uni-Fi UVC-G3-PRO User manual

UVC-G3-PRO Quick Start Guide
×
1080p Indoor/Outdoor IP Camera with Infrared and Optical Zoom
Model: UVC-G3-PRO
Table of Contents
Installation Requirements
Hardware Overview
Hardware Installation

Connecting Power
UniFi Protect App
Adjusting the Camera View
Specifications
Safety Notices
Electrical Safety Information
Installation Requirements
Pole-mounting: Two metal straps / hose clamps (not included)
Shielded Category 5 (or above) cabling with drain wire should be used for all
outdoor wired Ethernet connections and should be grounded through the AC
ground of the PoE.
We recommend that you protect your networks from harmful outdoor
environments and destructive ESD events with industrial-grade, shielded
Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable
Surge protection should be used for all outdoor installations. We recommend that
you use two Ethernet Surge Protectors, model ETH-SP, one near the camera
and the other at the entry point to the building. The ETH-SP will absorb power
surges and safely discharge them into the ground.
Hardware Overview

Ethernet Port
10/100 RJ45 port connects to an 802.3af/802.3at or 24V Passive PoE switch for PoE power
and data.
Reset Button
To reset to factory defaults, press and hold the Reset button for more than 10 seconds while
the camera is powered on.
Hardware Installation
Wall/Ceiling Mount

1.
2.
3.

4.
5.
Or

6.

7.
8.

9.
10. Proceed to the Connecting Power section.
Pole Mount
1.

2.
3.

4.
5.
Connecting Power
The UVC G3 Pro supports 802.3af, 802.3at, and 24V Passive PoE and can be
powered by any 802.3af/802.3at or 24V Passive PoE compliant switch, such as a
UniFi PoE Switch.
Connect the Ethernet cable from the camera directly to a PoE port on the switch.

Setting Up UniFi Protect via App
Download and install the UniFi Protect app to configure the UVC-G3-PRO.
Launch the UniFi Protect app and follow the on-screen instructions to complete
setup.
Adjusting the Camera View

1.
2.

3.
4.
5.
Specifications

UVC-G3-PRO
Dimensions
(Without Mounting Plate)
Ø 86 x 153 mm (Ø 3.39 x 6.02")
Weight
(Without Mounting Plate)
700 g (1.54 lb)
Enclosure
UV Stabilized Polycarbonate and Die-Cast Aluminum
Networking Interface
(1) 10/100 Ethernet Port
Sensor
Sony IMX290, 1/2.8"
Lens
3-9 mm, f/1.2-f/2.1 Powered Zoom Lens
Field of View
Wide
108° (H), 58° (V), 125° (D)
Tele
37° (H), 20° (V), 43° (D)
Night Mode
IR LEDs with Mechanical IR Cut Filter
Video Compression
H.264
Resolution
1080p Full HD (1920 x 1080)
Maximum Frame Rate
30 FPS
Image Settings
Flip, Brightness, Contrast, WDR, Hue, Infrared, Sharpness,
Saturation, Denoise, 50/60 Hz Flicker Reduction
Management Interface
Managed Mode
UniFi Protect
Standalone Mode
Camera Integrated Web UI
Microphone
Yes
Max. Power Consumption
12.5W
Power Method
IEEE 802.3af/at Type 2 PoE or 24V Passive PoE
Power Supply
802.3af/802.3at or 24V Passive
PoE Switch
Buttons
Factory Reset Button
Mounting
Wall/Ceiling (Kits Included)
Pole (Bracket Included)

UVC-G3-PRO
Operating Temperature
-20 to 50° C
-4 to 122° F
Operating Humidity
0 to 90% Noncondensing
Weatherproofing
IP67
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Hot surface. Do not touch.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements
indicated on the manufacturer’s label. Connection to a different power source than those
specified may result in improper operation, damage to the equipment or pose a fire hazard if
the limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided
only by a qualified service technician.