Unitron Johansson 7472L1 User manual

User Manual
Smart Amp
Ref. 7472L1 –7472L2
PATENTED TECHNOLOGY
SW Version 1.0

SMART AMP (REF. 7472L1 –7472L2)
2
CONTENTS
1. INTRODUCTION ...............................................................................3
1.1. Product description ...................................................................................3
1.2. Package contents .....................................................................................3
2. TECHNICAL SPECIFICATIONS ..............................................................3
3. HARDWARE INSTALLATION.................................................................5
Installing the Smart Amp ....................................................................................5
Duplicate channel switch OFF: .............................................................................5
Duplicate channel switch ON:...............................................................................7
LTE Filtering ......................................................................................................6
How Autoscan works: .........................................................................................5
How to force channel scan:..................................................................................6
4. SAFETY INSTRUCTIONS .....................................................................8
5. CONDITIONS OF WARRANTY ...............................................................9
No part of this manual may be copied, reproduced, transmitted, transcribed or translated into any language without
permission.
Unitron reserves the right to change the specifications of the hardware and software described in these manuals at any
time.
Unitron cannot be held liable for any damages resulting from the use of this product. Specifications are
subject to change without notice. 01/22
©Unitron - Frankrijklaan 27 - B-8970 Poperinge - Belgium
T+32 57 33 33 63 F+32 57 33 45 24
[e-mail]
www.unitrongroup.com

SMART AMP (REF. 7472L1 –7472L2)
3
1. INTRODUCTION
1.1. Product description
•Scans all channels, amplifies the weak signals while keeping the strong channels
•All output channels have an equal and stable output power
•Treats even the most difficult situations with adjacent channels
•Channels with the same frequency can be amplified in and re-located to the LTE
band (switchable)
•Fully automatic channel scan and process function upon double power start-up.
•Fully automatic recognition of the applied country channel plan
•SAW filters for LTE (4G or 5G) protection on all inputs
•Outdoor weatherproof mast-head housing
•DC Power over coax
•All ports ESD protected
1.2. Package contents
•1 Smart Amp (ref. 7472L1 –7472L2)
•Optional: Power Supply 12V (ref. 2437)
2. TECHNICAL SPECIFICATIONS
7472L1
7472L2
Inputs
-
2
2
Outputs
-
4G (> CH60)
5G (> CH48)
Frequency range
-
VHF BIII + UHF
Automatic channel plan selection
LTE band rejection
dB
>40
Output
-
1
Output Power
dBµV
90
Frequency Range
MHz
174 - 862
LTE band Re-use
-
L1 = CH61-69 (790MHz-
862MHz)
Switch ON-OFF
L2 = CH49-69 (694MHz-862MHz)
Switch ON-OFF
Adjacent channel isolation
dB
>35
Input sensitivity
dBµV
40
Operating temperature
°C
-20 to +50
Power Supply
-
External power supply (ref. 2437 - 2 out)
Power
-
12V/300mA (DC over coax) (275mA - 2 in)
Dimensions
mm
120 x 115 x 50

SMART AMP (REF. 7472L1 –7472L2)
4
Power Supply
ref. 2437
Outputs
-
2
Loss
dB
4 - 5
Frequency range
MHz
174 - 862
Isolation between outputs
dB
10
DC output voltage
VDC
12
Alimentation
V
12 stabilized
AC input voltage/
frequency/ power
-
110-240 VAC / 50-60 Hz / 6,5 W
Standard
-
EN50083-2
Output current
mA
400 max.
Insulation class
-
II
Connectors
-
F-type Female
Operating temperature
°C
0 to +50
Mounting
-
Mast or DIN rail (IP20)
Dimensions
mm
95 x 76 x 35
Power supply supplied only in the KIT version

SMART AMP (REF. 7472L1 –7472L2)
5
3. HARDWARE INSTALLATION
Installing the Smart Amp
•Connect your Terrestrial antennas to the Smart Amp*
•Connect the Smart Amp output to the Power Supply
•Connect your TVs to the Power Supply
Important: Mount the module vertically to a wall in a well-ventilated room and leave a
minimum space of 15 cm around the product to guarantee a maximum ventilation of
the product
* The Smart Amp does not allow pass-through DC-power for pre-amplifiers or active
antennas
How Autoscan works:
•Plug in Power Supply
•Status LED will blink green when scanning
•Status LED solid green when autoscan ready (This can take up to 20 seconds)
•Status LED red when error during scan. Unpower and repower within 6 seconds
to restart autoscan
•WARNING: do not turn off the power during SCAN

SMART AMP (REF. 7472L1 –7472L2)
6
•When a power outage causes missing channels on your TV, a reset is needed
•Reset: pull out the power supply and put it back in within 6 seconds
•The status LED will blink when re-scanning
•If a power interruption lasts longer than 6 seconds, there is no channel scan and
the initial settings are kept
•Important note for installers! Do not cut the power plug and insert
power supply directly to a power cabinet/power strip. Make sure the
end-user or installer can easily and safely unpower and repower device
LTE Filtering
LTE1 = LTE800 = 4G (REF. 7472L1)
Everything above 790MHz is filtered out:
LTE2 = LTE700 = 5G (REF. 7472L2)
Everything above 694MHz is filtered out:

SMART AMP (REF. 7472L1 –7472L2)
7
Duplicate channel switch OFF:
Weakest channel is rejected. See example below:
CH30 > CH30 ➔CH30 is transmitted
➔CH30 is rejected
CH40 <CH40 ➔CH40 is rejected
➔CH40 is transmitted
Duplicate channel switch ON:
Weakest channel is converted to LTE band. See example below:;
CH30 > CH30 ➔CH30 is transmitted
➔CH30 is converted to LTE band
CH40 <CH40 ➔CH40 is converted to LTE band
➔CH40 is transmitted

SMART AMP (REF. 7472L1 –7472L2)
8
4. SAFETY INSTRUCTIONS
Read these instructions carefully before connecting the unit
To prevent fire, short circuit or shock hazard:
• Do not expose the unit to rain or moisture.
• Install the unit in a dry location without infiltration or condensation of water.
• Do not expose it to dripping or splashing.
• Do not place objects filled with liquids, such as vases, on the apparatus.
• If any liquid should accidentally fall into the cabinet, disconnect the power plug.
To avoid any risk of overheating:
• Install the unit in a well aired location and keep a minimum distance of 15 cm around the
apparatus for sufficient ventilation
• Do not place any items such as newspapers, tablecloths, curtains,
on the unit that might cover the ventilation holes.
• Do not place any naked flame sources, such as lighted candles, on the apparatus
• Do not install the product in a dusty place
• Use the apparatus only in moderate climates (not in tropical climates)
• Respect the minimum and maximum temperature specifications
To avoid any risk of electrical shocks:
• Connect apparatus only to socket with protective earth connection.
• The mains plug shall remain readily operable
• Pull out power plug to make the different connections of cables
• To avoid electrical shock, do not open the housing of adapter.
Maintenance
Only use a dry soft cloth to clean the cabinet.
Do not use solvent
For repairing and servicing refer to qualified personnel.
Dispose according your local authority’s recycling processes

SMART AMP (REF. 7472L1 –7472L2)
9
5. CONDITIONS OF WARRANTY
Unitron N.V. warrants the product as being free from defects in material and
workmanship for a period of 24 months starting from the date of production indicated on
it. See note below.
If during this period of warranty the product proves defective, under normal use, due to
defective materials or workmanship, Unitron N.V, at its sole option, will repair or replace
the product. Return the product to your local dealer for reparation.
THE WARRANTY IS APPLIED ONLY FOR DEFECTS IN MATERIAL AND
WORKMANSHIP AND DOES NOT COVER DAMAGE RESULTING FROM:
•Misuse or use of the product out of its specifications,
•Installation or use in a manner inconsistent with the technical or safety standards in
force in the country where the product is used,
•Use of non-suitable accessories (power supply, adapters...),
•Installation in a defect system,
•External cause beyond the control of Unitron N.V. such as drop, accidents,
lightning, water, fire, improper ventilation…
THE WARRANTY IS NOT APPLIED IF
•Production date or serial number on the product is illegible, altered, deleted or removed.
•The product has been opened or repaired by a non-authorized person.
NOTE
Date of production can be found in the product’s serial number code. The format will either
be “YEAR W WEEK” (e.g., 2017W32 = year 2017 week 32) or “YYWW” (e.g., 1732 = year
2017 week 32).
UNITRON NV
Frankrijklaan 27
B-8970 Poperinge
Belgium
T [phone]
F [phone]
[e-mail]
www.unitrongroup.com