Universal Remote Control Easy Clicker UR3L-SR4 User manual

Universal Remote Control, Inc.
www.universalremote.com
UR3L-SR4
Operating Manual
For Easy Clicker

1
This remote control is designed to operate most Digital
and Analog Cable Boxes, as well as TVs, and a VCR or
DVD player.
Introduction
1
Before you program or operate the remote control, you must
install two new AAA alkaline batteries.
STEP1 Remove the battery compartment cover from the
back of your remote control.
STEP2 Check battery polarity carefully, and install the batter-
ies as shown in the illustration below.
STEP3 Replace the battery compartment cover.
Replacing Batteries
2

2
Button Functions
3
Programming the Remote Control.
4
*Note : In this section, when you are instructed to press a
[DEVICE] button, that means you should press either
the CBL, TV, or DVD button, depending on which
device you are programming the remote to operate.
A.
A.
Manual Pr
Manual Programming ogramming
The remote control can be programmed by entering a three-
digit code number that corresponds to particular brands and
models of equipment. The three-digit code numbers are listed
in the code tables sections of this instruction manual.

3
STEP1 Turn on the equipment that you want the remote con-
trol to operate Cable Box, TV and DVD.
STEP2 Press the [DEVICE] button and the [OK/SEL] button
simultaneously for three seconds. The corresponding
device LED will turn on indicating that it is ready to be
programmed. The LED will remain on for 30 seconds.
The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and
enter the three-digit code number assigned to your
brand from the code tables. If there are more than
one three-digit number listed for your brand, try one
code number at a time until your equipment turns off.
*Note : You can verify that you have selected the correct code
by pressing the [POWER] button. The equipment
should turn on or off.
STEP4 Store the three-digit code by pressing the same
[DEVICE] button once again. The device LED will blink
twice to confirm that the code has been stored.
*Note : Try all the functions on the remote control. If any of the
functions do not operate as they should, repeat the
instructions from Step 2 using the next three-digit code
number from the same brand list.
B.
B.
Auto Sear
Auto Search Method ch Method
If none of the three digit code numbers assigned to your brand
of equipment works, or the code table does not list your brand,
you can use the Auto Search Method to find the correct
three-digit code number for your equipment by following
steps:
STEP1 Turn on the equipment that you want the remote con-
trol to operate (Cable Box, TV or DVD).
STEP2 Press the [DEVICE] button and the [OK/SEL] button
simultaneously for three seconds. The device LED
will turn on indicating that it is ready to be pro-
grammed. The LED will remain on for 30 seconds.
The next step must be entered while the LED is on.

4
STEP3 Press the [CH+] or [CH-] button one at a time or keep
it pressed. The remote will emit a series of Power
ON/OFF code signals. Release the [CH+] or [CH-] but-
ton as soon as the equipment turns off.
*Note : You can verify that you selected the correct code by pressing
the [POWER] button. The equipment should turn On or Off.
STEP4 Press the same [DEVICE] button to store the code.
The Device LED will blink twice to confirm that the
code has been stored.
C.
C.
T
To find the Thr o find the Three-Digit Code that W ee-Digit Code that Was as
Pr
Programmed using the Auto Sear ogrammed using the Auto Search Method ch Method
STEP1 Press the appropriate [DEVICE] button and the
[OK/SEL] button simultaneously for three seconds.
The device LED will turn on for 30 seconds. The next
step must be performed while the LED is on.
STEP2 Press the [INFO] button. The device LED will blink a
number of times indicating the number of each digit
for the code. Each digit is separated by a one second
interval of the LED being off.
Example : One blink, then three blinks, then eight blinks indi-
cates the code number 138.
*Note : Ten blinks indicates the number 0.
D.
D. Pr Programming a Second TV to the DVD Button ogramming a Second TV to the DVD Button
STEP1 Press the [DVD] button and the [OK/SEL] button
simultaneously for 3 seconds. The DVD LED will turn
on for 30 seconds. The next step must be performed
while the LED is on.
STEP2 Press the [TV] button.
STEP3 Point the remote control toward the TV and enter the
three-digit code for your TV from the TV codes table.
STEP4 Store the three-digit code by pressing the [DVD] but-
ton. The device LED will blink twice to confirm that
the code has been stored.

5
E.
E.
The Lear
The Learning Method ning Method
STEP1 Press the [COMPONENT] button (CBL, TV or DVD) to
be programmed and the [INPUT] buttons simultane-
ously for 3 seconds until the Component LED light
turns on.
STEP2 Line up the UR3L-SR4 to the other remote, head-to-
head, 1 or 2 inches apart.
STEP3 Press any button on the UR3L-SR4 that you want to
teach a command to. For example, if you want to
teach the [MUTE] button, press the [MUTE] button.
STEP4 Press and hold the [MUTE] button on the other remote
until the UR3L-SR4 Component LED light blinks twice.
*Note : The LED will blink 5 times if there was an error in the
learning process. In so, repeat STEPS 3 and 4. Continue
learning other buttons by repeating STEPS 3 and 4.
STEP5 Once you have completed teaching UR3L-SR4 all
desired commands for that Component, save the
learned commands by pressing the [COMPONENT]
and [INPUT] buttons simultaneously until the
Component LED blinks 3 times. Now test all the but-
tons to make sure they learned correctly.
F
F. . Erasing a Single Lear Erasing a Single Learned Command ned Command
STEP1 Press the [COMPONENT] and [INPUT] buttons simul-
taneously for 3 seconds until the Component LED
light turns on.
STEP2 Press and hold the button you want to erase for 3
seconds. The Component LED will blink twice to con-
firm the erasure.
STEP3 To exit, press and hold both the [COMPONENT] and
[INPUT] buttons simultaneously until the Component
LED blinks 3 times.

6
G.
G. Erasing All Lear Erasing All Learned Commands fr ned Commands from om
One Component
One Component
STEP1 Press the [COMPONENT] and [INPUT] buttons simul-
taneously for 3 seconds until the Component LED
light turns on.
STEP2 Press and hold both the [COMPONENT] button you
want to erase and the [PAUSE] button for 5 seconds.
The Component LED will blink twice to confirm the
erasure.
STEP3 To exit, press and hold both the [COMPONENT] and
[INPUT] buttons simultaneously until the Component
LED blinks 3 times.
H. Pr
H. Programming the All Of ogramming the All Off Button f Button
This allows you to program the All Off button so it can send up
to three power On/Off commands with one button press.
STEP1 Press the [CBL] button.
STEP2 Press the [All OFF] button and the [OK/SEL] button
simultaneously for 3 seconds. The [CBL] button will
turn on for 30 seconds.
STEP3 Press the first [COMPONENT] button you want to
store in the [ALL OFF] button and then the [POWER]
button. Repeat this for other Components until you
have stored all the desired power commands into the
[ALL OFF] button.
STEP4 Press the [CH+] button to save the power commands
you stored. The [CBL] button will blink twice to con-
firm the commands have been saved.
I. Pr
I. Programming for Advanced Functions. ogramming for Advanced Functions.
If your remote model has custom-programmable Macro but-
tons available, they can be programmed to act as a ‘Macro’ or
Favorite Channel button in CABLE mode. This allows you to pro-
gram up to five 2-digit channels, four 3-digit channels or three 4-
digit channels that can be accessed With one button press.

7
**Note : The FAV button is not programmable if you have a
Digital Cable Box made by Pace, Pioneer or
CISCO/SA.
STEP1 Press the [CBL] button to select the CBL mode.
STEP2 Press the [MACRO] button and [OK/SEL] button
simultaneously for 3 seconds. The [CBL] button will
turn on for 30 seconds.
STEP3 Enter the the 2, 3 or 4-digit code for the channel you
want programmed first (for example, 007) using the
Number Pad, then press the [STOP] button. Then
enter the code for the next channel (for example,
050), then press the [STOP] button. Repeat this
process for the third channel. The [CBL] button will
blink once for each channel entered.
STEP4 Press the [CH+] button to store the channels that
were selected. The [CBL] button will blink twice to
confirm the storage of commands.
To access the programmed channels, press the [MACRO]
button once. This will bring up the first channel. Press once
again and it will bring up the second channel. Press again
and it will bring up the third channel.
To erase the Macro programming and return to the original
function:
STEP1 Press the [CBL] button to select the CABLE mode.
STEP2 Press a [MACRO] button and the [OK/SEL] button
simultaneously for 3 seconds. The CBL device LED
will turn on for 30 seconds. The next step must be
performed while the LED is on.
STEP3 Press the [CH+] button to erase the functions stored
in the button. The CBL device LED will blink twice to
confirm that the memory button has been erased.

8
J.
J. Assigning the V Assigning the Volume and Mute keys to a olume and Mute keys to a
Dif
Differ ferent Device ent Device
CBL : TV TV : TV DVD : TV
STEP1 Press the [OK/SEL] button and [CBL] button simulta-
neously for three seconds. The device LED Will turn
on for 30 seconds. The next step must be performed
while the LED in on.
STEP2 Press the [VOL+] button. The device LED will blink.
STEP3 Press the [CBL] button corresponding to the device
that you would like the volume and mute buttons to
control. The device LED will blink twice to confirm
the programming.
Example : If you wish to have the volume and mute keys oper-
ate your TV, press the [TV] button in Step3.
K.
K. Assigning the Channel keys to a Dif Assigning the Channel keys to a Differ ferent ent
Device
Device
CBL : CBL TV : CBL DVD : DVD
STEP1 Press the [OK/SEL] button and [TV] button simultane-
ously for three seconds. The device LED Will turn on
for 30 seconds. The next step must be performed
while the LED in on.
STEP2 Press the [VOL-] button. The device LED will blink.
STEP3 Press the [TV] button corresponding to the device
that you would like the volume and mute buttons to
control. The device LED will blink twice to confirm
the programming.
*Note : If you wish to have the channel keys operate your Cable Box,
press the [CBL] button instead of the [TV] button in Step3.

9
L.
L. Low Batter Low Battery W y War arning ning
When the battery is low (2.3V-2.0V) and needs to be replaced
with fresh batteries, device LED will blink 2 times in sequence
whenever a [DEVICE] button is pressed to turn on equipment.
M.
M. Memor Memory Lock System. y Lock System.
This remote control is designed to retain programmed memo-
ry for 10 years — even after batteries are removed from the
remote control.
For additional information about your remote control, go to
www.universalremote.com

Set-up Code Tables
5
MAKER(BRAND) NAME
CODE No
CONVERTER
CABLE TV
CISCO/SA EXPLORER Series 001 007
8600X 011
8600 021
8540,8570,8590 022
8500 023
MOTOROLA DCT Series (DVR Model) 002
GENERAL INSTRUMENT DCT Series,DCH Series, CFT2200 008
DL4,DQNV/DRX,DPBB,DPV/DP/DQN,DRZ 027
JERROLD BMC9012/BMC9022 006
DSR470 005
CFT2000 012
DL4,DQNV/DRX,DPBB,DPV/DP/DQN,DRZ 027
DIGEO 2056-MSX 153
DIRECTV HR20,HR21 229
MOXI MOXI MEDIA CENTER 006
MOXI HD DVR 052
2056-MSX 153
NFUSION NUVENIO SD PHOENIX, NUVENIO HD,
SOLARIS, NOVA 192
NSC IM781R 046
IM781 047
PACE 500 Series 001 007
TDC Series 002
510 004
PIONEER VOYAGER Series 001 007
BA9000 013
SAMSUNG OCAP MODELS 001 007
130
SKY SKY+HD 230
SKY HD 204
TELNET RC-RW100 154
10

11
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
TV
ADMIRAL 072 081 160 161 096
ADVENT 147
AIWA 141 145
AKAI 070 146 004 148 124 226 104 108
AKIO 103
ALARON 028
AMARK 112 127
AMERICA ACTION 043
AMPRO 073 167
ANAM 043 054 056 080 112 131
AOC 058 070 004 112
APEX 092
APEX DIGITAL 015 150 037
AQUAVISION 097 100
AUDIOVOX 076 103 043 035 078 224
AVION 223
BAYSONIC 043
BELL&HOWELL 072
BRADFORD 043
BROKSONIC 096 170
CAIRN 162
CANDLE 070 002 003 004
CAPEHART 058
CARVER 164
CELEBRITY 001
CETRONIC 043
CINERAL 103 120
CITIZEN 070 002 003 004 101 103 127
CLASSIC 043
CONCERTO 004
CONTEC 043 051
CORONADO 127
CRAIG 043 054 028
CROSLEY 164
CROWN 043 127
CURTIS MATHES 070 004 101 011 072 081 120 164 127
CXC 043
DAEWOO 076 103 112 004 127 016 043 044 125 120
DAYTRON 004 127
DELL 041
DENON 011
DIGITAL PROJECTION 090
DUMONT 004 073
DWIN 131 132 161
DYNASTY 043
DYNATECH 062

12
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
TV
FISHER 007 057
ELECTROBAND 001
ELECTROHOME 024 076 127
ELEMENT 004 110
EMERSON 005 028 043 048 076 096 155 004 051 151 153 154
127 121
ENVISION 070
EPSON 087 228
ESA 031
FUJITSU 164 197 028 157 149 066 217
FUNAI 028 043 052 168
FUTURETECH 043
GATEWAY 165 031
GE 070 073 130 144 160 161 004 008 009 034 056 074
091 155 081 120
GEM 031
GIBRALTER 004 073
GOLDSTAR 004 106 112 127
GRUNPY 028 043
HAIER 004 116
HALL MARK 004
HANNSPREE 099
HARLEY DAVIDSON 028
HARMAN KARDON 164
HARVARD 043
HISENSE 198 021
HITACHI 004 007 009 011 072 010 012 023 075 158 127 174
HP 027 039 098
HUMAX 122
HYUNDAI 049 067
ILO 055 096
INFINITY 164
INFOCUS 046 215 225
INKEL 129
INSIGNIA 068 069 078 096 164 168
INTEQ 073
JBL 164
JCB 001
JCPENNEY 004 008 024 030 065 070 101 160 156 127
JENSEN 013
JVC 038 001 034 083 195 159 227
KENWOOD 070 001
KLEGG 220
KLOSS 002 059
KREISEN 202
KTV 070 043 154 127

13
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
TV
LG 004 106 112 127 086
LODGENET 072
LOEWE 196 164
LOGIK 072
LUXMAN 004
LXI 007 015 052 081 160 164
MAGNAVOX 070 003 004 022 059 060 061 063 064 127 164 094
160 056 028 035 211 205 218 050 138
MAJESTIC 072
MARANTZ 164 070 143 169
MATSUI 164
MATSUSHITA 080
MAXENT 165
MEGATRON 004
MEMOREX 004 007 072 028 096
METZ 088
MGA 024 070 004 042
MIDLAND 073
MINERVA 088
MINTEK 077
MINUTZ 008
MITSUBISHI 109 024 042 004 040 146 028 124 081 200
MOTOROLA 081
MTC 070 004 062 101
MULTITECH 043
NAD 015 025
NEC 070 130 134 040 056 007 019 024 004 182 140
NIKEI 043
NIKKO 103
NIKO 175
NORCENT 211
NTC 103
NUVISION 084
OLEVIA 219 004 161 144 160
ONKING 043
ONWA 043
OPTIMUS 080
OPTOMA 029 032
OPTONICA 019 081
ORION 096 201 203 204 205 028
PANASONIC 034 056 080 164 190 230 248
PHILCO 070 003 004 024 056 059 060 063 064 127 164
PHILIPS 164 005 038 093 127 070 003 004 059 199 218 161
232
PIONEER 023 025 135 176 004 018 070 183 191 208 214 182
POLAROID 026 118 119 006

14
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
TV
PORTLAND 004 103 127
PRISM 034
PROSCAN 144 160 161 167
PROTON 004 058 171 173 193 127 163
PROTRON 102 213 004 115
PROVIEW 110
PROX 092
QUASAR 034 056
RADIO SHACK 004 019 127 043
RCA 160 161 144 156 065 070 004 023 024 056 074 152
081 209
REALISTIC 007 019
REVOLUTION HD 220
RUNCO 072 073 130 179 180 181 182 216 194
SAMPO 070 004 058 165
SAMSUNG 004 101 127 133 160 089 105 070 184 185 192
SANSEI 120
SANSUI 096
SANYO 007 053 057 082 020
SCEPTRE 036
SCOTCH 004
SCOTT 004 005 028 043 048 127 113
SEARS 004 007 015 028 030 057 082 094 160 052 164 127
SELECO 189
SEMIVOX 043
SEMP 015
SHARP 081 014 019 028 004 022 127
SHERWOOD 128
SIGNATURE 072
SOLE 177 178
SONY 001 085 126 139
SOUNDESIGN 003 004 028 043
SOYO 163
SPECTRICON 112
SPECTRONIQ 004
SQUAREVIEW 052
SSS 004 043
STARLITE 043
SUPRE MACY 002
SUPREME 001
SVA 046
SYLVANIA 070 003 059 060 063 064 127 160 164 044 056 168
121 231
SYMPHONIC 052 168
SYNTAX OLEVIA 219 004 161 144 160
TANDY 081

15
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
TV
TATUNG 056 062
TECHNICS 034 080
TECHNOL ACE 028
TECHVIEW 246
TECHWOOD 004
TEKNIKA 002 003 004 024 028 043 072 101 103 164 127
TELERENT 072
TERA 172
THOMPSON 166
TNCI 073
TMK 004
TOSHIBA 015 030 007 040 062 101 142 045 137
TOTEVISION 127
TRUTECH 212
UNIVERSAL 008 009
VIDEO CONCEPTS 146
VIDIKRON 188 164 182
VIDTECH 004
VIEWSONIC 210 211
VIORE 055 229
VISCO 110
VIZIO 004 031
WARDS 004 064 164 008 009 019 028 060 061 063 072 074
070 127
WESTINGHOUSE 076 036 221 222 001
WINBOOK 079
YAMAHA 004 070 206 207
YORK 004
YUPITERU 043
ZENITH 011 072 073 095 103 096
ZONDA 112

MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
DVD
ADCOM 203
AIWA 210 214
AKAI 239
ALPINE 179
APEX DIGITAL 240 197 247 248 196
ARCAM 165 148
AUDIOVOX 075
BOSE 244 245
CAMBRIDGE AUDIO 224 145
CARY AUDIO DESIGN 249 149
CLASSE 242
COBY 206
CYBERHOME 170 212
DAEWOO 170
DENON 184 226 225
DURABRAND 235
EMERSON 235
ESA 235
FUNAI 235
GE 188 189
GOLDSTAR 182 194
GO VIDEO 228 182 252 253 254
GRADIENTE 243
HARMAN KARDON 217
HITACHI 181
HITEKER 197
INSIGNIA 078 235 085 182 178
INTEGRA 208 236 238 128
JVC 185
KENWOOD 166
KISS 237
KLH 230
KOSS 243
KRELL 218
LEXICON 216
LG 182 194
LITEON 150
MAGNAVOX 178 191 195 235
MARANTZ 176 177 135
MCINTOSH 167
MEMOREX 222
MERIDIAN 200
MINTEK 240 196
MITSUBISHI 186
MYRYAD 211
NAD 198 182
16

17
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
DVD
ONKYO 207 236 128
OPPO 125
OPTIMUS 187
ORITRON 243
PANASONIC 076 173 184 219 192
PARASOUND 083
PHILIPS 074 164 176 177 191 195 209 127
PIONEER 175 180 187 221 223
POLAROID 075 084 085
PRIMARE 250 251
PROCEED 172
PROSCAN 188 189
RCA 188 189 086
SANSUI 201
SANYO 215
SAMSUNG 183 193 228 205 073 152 241
SENSORY SCIENCE 254 255
SHARP 174
SHERWOOD 083
SONY 077 168 190 213 118 119 120 121 126
SPECTRONIQ 088
SUPERSCAN 235
SV2000 235
SYLVANIA 235
SYMPHONIC 235
TAG McLaren 202
TECHNICS 173
THETA DIGITAL 187
TOSHIBA 169 171 191 206 227 201 236
TRUTECH 151
VENTURER 229
VINC 220 087
YAMAHA 199 204 246 184 192
ZENITH 182 194
DVR(TIVO)
DIRECTV 819
HUGHES 817
HUMAX 817
PHILIPS 790 817
RCA 809
REPLAY NETWORKS 775
SONY 804 805
TIVO 790 817
TOSHIBA 817

18
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
VCR(DVD)
ADVENTURA 534
AIWA 534
AKAI 543
ANAM 645
AUDIO DYNAMICS 512 543
AUDIOVOX 601
BROOKSONIC 629
CALIX 601
CANON 645
CITIZEN 601
CRAIG 503 602
CURTIS MATHES 645
DAEWOO 612
DBX 512 543
DYNATECH 534
ELECTROHOME 559
ELECTROPHONIC 601
EMERSON 506 645 534 601 629 631 653
FISHER 503 508
FUNAI 534
GARRARD 534
GE 645 647 644
GO VIDEO 602
GOLDSTAR 601 513 512 623
GRADIENTE 534
HARLEY DAVIDSON 534
HARMAN KARDON 512
HITACHI 534 543 513
HQ 534
INSTANTREPLAY 645
JCL 645
JCPENNEY 512 513 602 601
JENSEN 543
JVC 548 543 512 645
KEC 601
KENWOOD 548 534
KODAK 645 601
LG 601 513 512 623
LLOYD 534
LXI 534 503
MAGIN 602
MAGNAVOX 567 645 534
MARANTZ 567 512 645
MARTA 601
MATSUSHITA 645
MEI 645