UNV OEI-371S-H-W Quick reference guide

Video Intercom Deployment Guide
V1.2
Zhejiang Uniview Technologies Co., Ltd.

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
i
Contents
1Introduction ··············································································································1
1.1Product Overview···········································································································1
1.2Installation···················································································································1
1.3Networking ··················································································································1
1.3.1Device······················································································································1
1.3.2Network Environment Setup····························································································1
1.3.3Indoor Station Home Screen ···························································································2
2Video Intercom Configuration ·························································································3
2.1Indoor Station Wizard Configuration·····················································································3
2.2Indoor Station Manual Configuration ····················································································7
2.3Outdoor Station Configuration ·························································································13
2.3.1Door Station ············································································································13
2.3.2Face Recognition Access Control Terminal ·········································································17
2.4Network Camera Configuration·························································································19
3Video Intercom Operations··························································································· 20
3.1Video Intercom with Door Station ······················································································20
3.2Video Intercom with Face Recognition Access Control Terminal ···················································21
3.3Call Extension ·············································································································24
3.4Call App ····················································································································25
4Common Functions ··································································································· 28
4.1Live View ···················································································································28
4.2Configuring Multiple Doors for Door Stations ·········································································30

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
1
1 Introduction
1.1 Product Overview
OEI-371S-H-W/OEI-372S-H-W indoor station is a terminal in the digital building intercom system, with
functions of video intercom, security alarm, network camera monitoring, etc., providing a safe and
comfortable living environment for residents. It can be widely used in building systems such as smart
communities, public security, and parks.
OEU-201S-HMK-W is a terminal in the digital building intercom system, with functions of video intercom,
security alarm, and video surveillance, providing a safe and comfortable living environment for residents. It
can be widely used in villa residential building system.
1.2 Installation
For product installation, please see the corresponding quick guide as below.
Indoor Station
3101C1HS-UNV-
OEI-371S-H-W-人脸门禁一体机快速入门-V1.00-EN.pdf
Door Station
3101C1LF-UNV-O
EU-201B-HMK-W-Villa Door Station Quick Guide-V1.01-EN.docx
1.3 Networking
1.3.1 Device
The video intercom functioninvolves such devices as OEI-371S-H-W/OEI-372S-H-W indoor station, PoE switch,
face recognition access control terminal (hereinafter as “face recognition terminal”), door station, network
camera, router, and NVR.
1.3.2 Network Environment Setup
After the devices are ready, connect them as shown in the diagram below.

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
2
Figure 1-1 Video Intercom Product Network Environment
NOTE!
A 12V power can be used in indoor station, outdoor station (face recognition access control terminal/door
station), and network camera.
The indoor station can connect to power via the PoE interface.
1.3.3 Indoor Station Home Screen
The indoor station starts automatically after power-on, and the home screen appears. The home screen
shows the current time (settable on the Web interface) and buttons including Lock Screen, Do Not Disturb,
Live View, Call, Message, and Settings.
Figure 1-2 Indoor Station Home Screen
1. Lock Screen: Tap the Lock Screen button to lock the screen; Tap anywhere else on the screen to unlock.
By default, the screen needs to be locked manually. It can be also locked automatically.

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
3
2. Do Not Disturb: When Do Not Disturb is on, the indoor station does not sound when a call comes in, but
the call remains on the screen until it is answered or ended by the caller. By default, this function is disabled.
3. Live View: When the indoor station is connected to the outdoor station or network camera, you can view
live video on its screen.
4. Call: Used tocall other extensions in the same roomby inputting the corresponding number on the indoor
station. You can also view the calling records.
5. Message: It is used to view the snapshot records from the live view.
6. Setting: The indoor station’s screen supports sounds, display, time, password, Wi-Fi, and activation
configurations.
2 Video Intercom Configuration
The indoor station can realize video intercom, remote door opening, live view, and other functions with the
connected outdoor station and network camera. It can also communicate with other extensions in the same
room. The following describes how to configure on both the indoor station and outdoor station.
After configurations are complete, the indoor station and outdoor station can realize functions including
calling, live view, and remote door opening.
2.1 Indoor Station Wizard Configuration
The wizard page appears after your first login. You can follow the wizard to complete the first deployment
configuration.
Figure 2-1 Password and Email Settings
Log in to the device screen with the default username and password (admin/123456), and then the Welcome
screen appears. Set the new password, and enter your email address so as to retrieve the activation password
if you forgot the password.

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
4
Figure 2-2 Network Settings
1. Network settings: Obtain Automatically (DHCP) is enabled by default, which will assign the indoor
station an IP address automatically. You can skip the step if you want to keep the default configuration.
2. If you want to set a fixed IP address manually for long term use, enable Static IP, and then set the IP
address, subnet mask, and default gateway.
3. The indoor station’s IP address is 192.168.1.13 by default. When configuring a static IP for the first time,
the IP address shows 192.168.1.14 by default to prevent IP conflicts during installation, which can be
changed as needed.
NOTE!
The IP of outdoor station and network camera must be on the same IP segment as that of the indoor station,
and then the video intercom function can be available. You can search for IP addresses in different network
segments.
Figure 2-3 Wi-Fi Search
You can connect the network on the Wi-Fi screen. The Wi-Fi function is disabled by default. If you want to
connect to Wi-Fi, enable Wi-Fi; otherwise, tap Skip to proceed.

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
5
Figure 2-4 Wi-Fi Connection
Figure 2-5 Time Settings (Time Zone/DST/Time Sync)
Set time parameters, including time zone, time, and DST. If you do not need to set time, tap Skip to proceed.

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
6
Figure 2-6 Device Type and Location
The indoor station type includes main indoor station and extension (the extension can realize most of
functions after binding to the main indoor station). The default location information of the main indoor
station is District 1, Building 1, Unit 1, Room 1, extension 0 (cannot be modified); the extension location is
consistent with the associated main indoor station except the extension number.
NOTE!
The outdoor station (face recognition terminal and door station) is located at District 1, Building 1, Unit
1 by default.
The face recognition access control terminal can call the indoor station by entering the corresponding
room number on the screen. Press the physical button on the door station, and then the device that is
located at Building 1, Unit 1, Room 1 will be called by default.
Figure 2-7 Device Management
1. Refresh the device management list (it will be refreshed automatically when you enter the screen).
2. Select the video intercom devices (door station/indoor station extension) you want to relate.

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
7
3. Change the device’s IP address.
4. Change the device location.
5. Confirm to relate the device to the indoor station.
NOTE!
On the Device Management screen, the outdoor station and indoor station can be searched and their
IP addresses can be changed in different network segments
The devices must be on the same network segment and have the same room in order to communicate
with each other.
It takes 1 minute to save the related devices. If the indoor station restarts during the one minute, the
bound devices cannot be saved.
2.2 Indoor Station Manual Configuration
1. After the wizard is complete or skipped, the indoor station’s home screen appears after power-on.
2. Go to Setting > Activation Config, tap Enter project password,and enter the activation password (initial
password is 123456).
3. Enter the Indoor Station screen, and then set network and location parameters.
Figure 2-8 Activation Config
4. Configure network parameters.
(1) You can use DHCP to assign a dynamic IP address or set a static IP address.

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
8
Figure 2-9 Indoor Station Config
Figure 2-10 Network Settings
Figure 2-11 Wi-Fi Search

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
9
(2) Connect to Wi-Fi. 1. Enter the Wi-Fi screen and enable Wi-Fi. 2. The list will be refreshed
automatically after 3 to 6 seconds. You can also tap to refresh. 3. Select a Wi-Fi to connect.
Figure 2-12 Wi-Fi Connection
5. Device location: Set the indoor station’s location information including residential compound name,
district number, building number, unit number, and room number, which should be consistent with outdoor
station’s location.
Figure 2-13 Indoor Station Device Location

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
10
Figure 2-14 Main Indoor Station’s Device Location
6. Tap Apply to save the settings.
Figure 2-15 Extension Device Location

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
11
NOTE!
On the Device Location screen of the extension, only the extension number can be changed. Other location
information will be changed automatically with the main indoor station.
7. Connect devices: After configuring indoor station information, you need to connect the indoor station to
the outdoor station, and connect the extension to the main indoor station as below.
NOTE!
The binding function is only available to the main indoor station mode. Calling records between extensions
and other devices can be searched from the main indoor station.
Method 1: Go to Device List > Device Management, and bind devices to the indoor station.
(1) Refresh the device list.
(2) Select the device you want to relate (outdoor station/indoor station).
(3) Relate the device.
Figure 2-16 Device List
Figure 2-17 Device Management

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
12
Method 2: Enter the Door Station List screen, tap Add, and set the device information as below.
Figure 2-18 Door Station List
Figure 2-19 Door Station List
Figure 2-20 Device Info
(1) Enter the device name (optional).
(2) Enter the IP address (required).

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
13
(3) Select the device type (VIC-OutDoorStation,IPC).
(4) Enable Live View.
To bind an IPC, see 2.4 Network Camera Configuration for details.
Figure 2-21 Bound Devices
The bound devices (outdoor stations and network cameras) will be displayed in the red box above. Tap Edit
to view the device’s IP address.
Figure 2-22 Bind to Main Indoor Station on Extension
To bind the main indoor station on the extension’s screen, enter the Main Station screen of the extension, set
the name of the main station you want to show on the extension, enter the IP address of the main station,
and then tap Apply.
2.3 Outdoor Station Configuration
2.3.1 Door Station
Configure the network: Log in to the Web interface.
1. Before login, make sure the client computer and the door station is connected via network, and the Web
browser is IE 9.0 or higher.

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
14
2. Add the door station’s IP to trusted sites.
3. Enter the door station’s IP address (192.168.1.13 by default) in the address bar, and then press Enter.
4. Enter the username and password, and then click Login.
5. The default username/password is admin/123456 (If the activation password has been changed, you
need to use the new password to log in). A prompt will be displayed to change the default password at your
first login.
1
2
3
4
5
不勾选
6
7

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
15
(1) At your first login, you need to follow the on-screen instructions to install the latest plug-in;
otherwise, you cannot view the live video.
Figure 2-23 Plug-in Installation Prompt
(2) Enter the username and password (admin/123456 by default).
(3) (Optional) Select Live View, and then the live view will start automatically.
(4) Click Login, and the door station displays the Live View interface.
(5) After the first login, the Change Password dialog box appears, in which you must set a strong
password and enter your email address so as to receive the security code if you forgot the
password (or change the password on the interface). Then, use the new password to log in again.
Door station password: 9 to 32 characters, including digits, letters, and special characters.
Figure 2-24 Change Password and Bind Email

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
16
Figure 2-25 Live View
To use a wired network, set Obtain IP Address to Static and then set a static IP address as shown below.
To use a wireless network, connect to Wi-Fi as shown below.
Figure 2-26 Wired Network

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
17
Figure 2-27 Wi-Fi
1. Set Wi-Fi Mode to Wi-Fi.
2. Select the Wi-Fi to connect from the list.
3. Enter the Wi-Fi password and confirm the password.
4. Click Save, and then the Wi-Fi can be connected.
NOTE!
The IP of outdoor station and network camera must be on the same IP segment as that of the indoor
station. To use a wireless network, the indoor station should connect to a same Wi-Fi as the door station.
2.3.2 Face Recognition Access Control Terminal
Network settings
Press and hold for 3s on the screen, and input the activation password. On the Activation Config screen, tap
Communication Settings, change the device’s IP address, and then tap Save.

Zhejiang Uniview Technologies Co., Ltd.
Video Intercom Deployment Guide
Internal Use Only
18
Figure 2-28 Activation Config Screen
Set a wired Network. To set a fixed IP address for long term use, enable Static IP.
Figure 2-29 Wired Network
Location and call protocol settings:
On the device’s Activation Config screen, go to Basic Settings > Intercom Config.
Choose EI-3 Series Indoor Station for the indoor station protocol.
Device location: The building and unit information (default: 1) of the face recognition terminal should be
consistent with those of the indoor station.