Uplift Desk MON001 User manual

Zilker Single Monitor Arm
MON001
For assembly assistance,
visit upliftdesk.com/contact,
call 800-349-3839,
or email [email protected]
©2023 UPLIFT Desk®. All Rights Reserved
Scan QR code for
product webpage

2
Under no circumstances does the manufacturer accept warranty or liability claims for damages caused from
improper use of this product. Please provide these instructions to any new user or owner of the product.
CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may result
in damage or personal injury. Retain manual for future reference.
Warning: This product contains a spring mechanism that can cause injury. Be careful when
removing monitors as the arm can spring up when the weight of the monitor is removed.
Safety and Warnings
Base Base Cushion Bottom Plate Extension Arm
Spring Arm VESA Mount Monitor Screw
qty 4 Allen Wrenches
(set of ve:
1.5 mm, 2.5 mm,
4 mm, 5 mm, 6 mm)
Long Bolts
(two sizes included:
50 mm & 70 mm)
Base Plate
Package Contents
Parts for bolt-through assembly

3
© UPLIFT Desk • 800-349-3839 • [e-mail] • upliftdesk.com
Step 2.1 - Clamp Method
1. Peel the adhesive off the Base Cushion and attach it
to the underside of the Base.
2. Rest the Bottom Plate onto the Base’s bolt.
3. Fit the Base around the back of the desk and tighten
the Bolt & Bottom Plate into place using the 6 mm
Allen Wrench.
A. When placing the Bottom Plate on the Base’s bolt, make
sure the edge farthest from the hole is facing the back
of the Base and the edge closest to the hole aligns with
the front edge of the Bottom clamp. If you’re attaching
this to a UPLIFT V2 4-Leg Desk, this is the only way it will
t properly.
Note: If the clamp does not t on your desk edge, you
can increase or decrease the space between the clamp
by removing the bottom of the clamp and the Bolt,
and repositioning them. Using the 4 mm Allen Wrench,
unscrew the two screws holding the bottom of the
clamp (see g. 1).
B. For thinner desks (0.75’’ minimum), reassemble the
clamp as shown in g. 2. For thicker desks (3.75’’
maximum), reassemble the clamp, as shown in g. 3.
Note: If you’re mounting this to an UPLIFT V2 4-Leg Desk,
2.5’’ will be the maximum thickness that will work with
the clamp.
B.
C.
A.
Assembly Instructions
min
thickness
0.75’’
bottom
clamp
bolt
max
thickness
3.75’’
g. 1 g. 2 g. 3
WARNING: This product contains a spring mechanism that can cause injury. Be careful when removing monitors as the arm can
spring up when the weight of the monitor is removed.
Step 1
Determine your mounting method. There are two ways to
attach the Zilker Single Monitor Arm to your desktop:
Clamp Method: If you would like to attach the monitor
arm along the back edge of your desktop, follow the
Clamp Method instructions (Steps 2.1) and ensure your
desk is between 0.4” and 3.3” thick.
Bolt-Through Method: If you prefer to attach the monitor
arm through your desktop, follow the Bolt-Through
Method instructions (Steps 2.2) and ensure your desk is
between 0.4” and 1.8” thick.
Clamp Method Bolt-Through Method

4
Step 3
A. With the Base attached to the desk, it’s time to
assemble the remainder of the arm by next inserting
the Extension Arm into the Base.
Note: The Base comes with a pre-installed stopping-
pin on the post, (see g. 4) which limits the rotation
of the arm to 180 degrees. If you want a full 360 degree
rotation, remove the pin with the 1.5mm Allen Wrench.
B. Once the Extension Arm is inserted, insert the Spring
Arm into the Extension Arm.
g. 4
Step 2.2 - Bolt-through Method
To mount your monitor arm through a hole in your
desktop, rst measure the hole. It must be between a
minimum of 0.4’’ and a maximum of 3.15’’ in diameter.
Prepare the Base for the Bolt-through mount by rst
loosening the screw under the clamp with the 6 mm
Allen Wrench.
Note: screw may be tight. Once removed, separate the
clamp assembly from the Base.
1. With the Base upside down, place the Base Plate in
the pocket where the clamp assembly was.
2. Peel the adhesive backing off of the Base Cushion
and attach it over the Base and Base Plate as
shown.
Place assembly completely over the hole, and facing
the front of desk.
Select a Long Bolt: the 50 mm Bolt ts desks 0.6’’ to
1.38’’ thick, and the 70 mm Bolt ts desks 1.38’’ to 2.13’’
thick. Insert the Long Bolt through the Bottom Plate.
Note: The Bottom Plate must straddle the hole’s
diameter. As long as the hole isn’t larger than 3.15’’
then the Bottom Plate will work.
Thread the bolt into the Base assembly by hand and
tighten using the 6 mm Allen Wrench.
C.
A.
B.
D.
E.
F.

5
© UPLIFT Desk • 800-349-3839 • [e-mail] • upliftdesk.com
Step 4
A. After all components from Step 2 are in place, you
may choose to tighten the set screws which will lock
all the components together, and prevent them from
separating or drifting.
B. The set screws are located at each insertion point, and
marked in this instruction book with a “ ”.
• At the back of the Base, on the post where the
Extension Arm is inserted.
• At the top of the Extension Arm where the Spring
Arm is inserted.
C. Use the 2.5 mm Allen Wrench provided. Make sure not
to overtighten the set screws.
Step 5
Place your monitor face down on a at surface, making
sure not to scratch the screen. Next, attach the VESA
Mount to the back of your monitor using a Phillips-head
screwdriver and four Monitor Screws. The mount is
designed to t the industry standard VESA 75 mm & 100
mm hole patterns. Make sure the VESA Mount is securely
fastened to your monitor before moving on to the next
step.
Note: make sure the tab on the VESA Mount is facing the
top of your monitor.
*
**

6
Step 6
A. Insert your monitor and VESA Mount assembly into
the monitor joint at the end of the Spring Arm. Hold it
rmly as you insert it until you feel it click into place.
B. The Zilker Spring Arm tension is factory set for the
lightest monitor weight. To adjust the tension if the
monitor is too heavy for the minimum setting, hold the
Spring Arm horizontally and, using 5 mm Allen Wrench,
turn the set screw located at the top-center of the
Spring Arm toward the “+”.
C. Keep adjusting the tension until the monitor arm
holds its position when you let it go.
Step 7
A. Under the Spring Arm, there is a clip through which
your monitor’s wires can run. (see g. 5).
B. Inside the Extension Arm is a channel accessible by a
removable cover. Slide the cover up & out to place your
wires, then replace the cover in the reverse motion, in
& down. (see gs 6-7)
Monitor Ergonomics
Screen Distance: Set screen about an arm’s length
(approximately 18’’ - 28’’) from your eyes. If print is too hard to
read, it is better to make the print larger on your screen than
to move the screen closer to your eyes.
Monitor Height: The top of the monitor should be at or just
below eye level.
Monitor Tilt: The monitor
should be tilted slightly up so
it’s easier to see the screen
when the top of the monitor is
level with your eyes. If the ball-
joint holding the monitor does
not move, loosen each screw
using the 4mm Allen Wrench.
This should only take a couple
of turns, each. If you loosen too
much, and the monitor does not
stay in place, tighten slightly.
g. 5 g. 6 g. 7

7
© UPLIFT Desk • 800-349-3839 • [e-mail] • upliftdesk.com
Notes

SAVE THIS MANUAL
Study this manual carefully. If this product is sold, please provide this
manual to the buyer, installers, or support personnel operating the product.
Work Better. Live Healthier
AI-MON001-2.2
Copyright Notice: This manual is a component of this UPLIFT Desk product. This manual is a
part of the scope of delivery, even if the item is resold. This manual is also available on the
UPLIFT Desk website: upliftdesk.com. This manual is subject to United States copyright law.
©
upliftdesk.com
[email protected]
800-349-3839
512-614-3152