Uplift Technologies UL1-02 User manual

Single Motor Standing Desk Installation Manual
UL1-02
①Foot Parts Included Qty
②Right lifting leg A Screw M6x10 12
③Left lifting leg B Screw M6x16 8
④Side bracket C Screw M5x30 2
⑤Motor D Wood screw ST4.8x16 10
⑥Crossbeam E Wood screw ST4.2x16 2
⑦Hexagonal rod F Allen wrench 4mm 1
Step 1 G Cable clip 5
H Motor Gasket 1
I Handset 1
As picture show: Pass the Hexagonal rod (part 7) through
hexagonal hole of the Motor (part 5).
J Power cable 1
K Dowel 6
Step 2 Step 5
Connect the two desktop using Dowel (part K).
Insert the Hexagonal rod assembled in Step 1 into the hexagonal
hole of the Right lifting leg (part 2) through the Motor Gasket
(part H), and tighten it with (part C) Screw M5x30.
Step 6
Step 3
Attach Foot (part 1) to the Lifting leg (part 2 and 3) using (part B)
Screw M6x16.
Step 7
Insert the other side of the Hexagonal rod into the hexagonal
hole of the Left lifting leg (part 3), and attach the Crossbeam
(part 6) to the Lifting leg (part 2 and 3) using (part A) Screw
M6x10.
Step 4
Adjust Crossbeams to proper position to fit the desktop. Tighten the
(part D) Wood screw ST4.8x16 to lock. Attach the Handset (part I) to
the underside of the desktop using (part E) Wood screw ST4.2x16.
Step 8
Attach Side bracket (part 4) to the Crossbeam (part 6) using (part
A) Screw M6x10.
Connect the Motor cable (part 5) and Power cable (part J) to the
Handset (part I).
1
2
3
4
5
6
7
C
H
F
A
F
A
F
B
F
K
E
I
D
I
J

Instructions For Use
IMPORTANT: You must reset the desk prior to use.
Reset Procedure:
1. Press and hold the DOWN button on the handset until the
desk reaches its lowest height.
2. Release the DOWN button.
3. Press and hold the DOWN button about 5 seconds until the
handset display reads “RST”, the desk slightly rises 5mm and
stops.
4. Release the DOWN button. The desk is now ready for use.
Note: When the LED display shows an error code, the desk must
be RESET prior to use.
Upper and Lower Height Limits:
Set the UPPER Limit:
1. The handset display height > 92.5mm.
2. Press and hold the UP and DOWN buttons for about 5 seconds until
the handset sounds "di."
3. The desk upper limit height setting is successful.
Set the LOWER Limit:
1. The handset display height < 92.5mm.
2. Press and hold the UP and DOWN buttons for about 5 seconds until
the handset sounds "di."
3. The desk lower limit height setting is successful.
Removing the Upper or Lower Position:
1. Press the “UP” and “DOWN” button together for about 5 seconds
until the sounds “di”.
2. The upper or lower limits are now removed.
Adjust desk height
Press the UP or DOWN button to adjust the height of the desk.
Memory setting
1. Press the UP or DOWN button to move the desk to the desired
height.
2. Press and hold the "1, 2, 3, or 4” button about 2 seconds until
the LED display "S-".
Changing the anti-collision sensitivity:
1. Press and hold buttons "3" and "4" until the sounds "di", handset
display show number 0, 1, 2, 3, 4, 5, 6, 7, or 8.
0 = Close the anti-collision function
1, 2, 3 = Least sensitive
4, 5, 6 = Middle sensitive
7, 8 = Most sensitive
2. Press the "UP" or "DOWN" button to switch the number Middle
(#4, 5, 6) or Least sensitive (#1, 2, 3).
3. Press and hold the "UP" and "4" buttons until sounds "di", the desk
is now ready to use.
Lock the handset:
1. Press and hold the “4” and “2” buttons for about 5 seconds
until the sound “di”.
2. LED will show LOC.
3. Handset is now locked.
Unlock the handset:
1. Press and hold the “4” and “2” buttons for about 5 seconds
until the sound “di”.
2. LED will show the height display.
3. Handset is now unlocked.
Changing from inches to centimeters: (CN is centimeters. IH is
inches).
Press and hold the "4" and "1" buttons (about 5 seconds), until the
LED switches to "CN", and "IH".
TROUBLESHOOTING:
Error code Error cause Measure
E05 Anti-collision issue Please change the anti-collision sensitivity, least or middle sensitive the desk will be ready to
u
ERR
1. Handset disconnected
2. Lifting legs disconnected
3. Leg or handset faulty
Ensure that the lifting leg connection to the hexagonal rod, and that all cables are connected
to the handset.
Execute RESET.
(Abnormal sound of the lifting leg, please replace the leg)
If the error cannot be corrected through the described measure:
Unplug the power plug.
Wait approx. 5 minutes
Execute RESET.
If an error still occurs after these steps have been executed. Please contact your sales rep.
USB