UREC SBH-170 User manual

Ver. 01

User Manual
www.unavi-usa.com
Support : (855)558-6284

Thank you for choosing UREC as your vehicle’s digital driving recorder.
This user guide contains safety information, operating instructions, and warranty service information. Please be sure to read the
user guide thoroughly before operating this UREC, and keep for future reference.
UREC is a high-definition in-dash camcorder system that can assist you in keeping records of incidents that occur around your
vehicle. Please note this device is not guaranteed to record all incidents, as certain environmental factors may prevent normal
operation.
● For support and technical assistance, call toll-free
(855) 558-6284.
● The latest firmware and use instructions can be downloaded
via www.unavi-usa.com.
● Product Category : Vehicle in-dash image recording
apparatus
● Model No. : SBH-170
● Certification No. FCC ID : EMY007925
KCC ID : KCC-REM-2SP-SBH-170
● Authorized Distributor : E-sense Technology
/ Unavi USA, Inc.
● Manufacturer : Spire Technology
● Country of Manufacture : Republic of Korea
All rights to this program shall remain with Unavi USA, Inc. and shall be protected by the Copyright Act. If they are reproduced,
amended, or distributed without prior written consent of Unavi USA, Inc., violators shall be subject to criminal punishment of
imprisonment up to five years and monetary fine pursuant to the Software Copyright Act.
Support & Upgrade Certification
Copyright & Trademark

1
1.1 Important Safeguards and Disclaimers
1.2 Features
1.3 Components & Accessories
1.4 Components
1.5 How to Install
2.1 Connecting Power & Starting Up
2.2 Disconnecting Power & Shutting Down
2.3 Safe Mode
2.4 Constant Mode (Normal Recording)
2.5 Event Mode (Impact Recording)
2.6 Parking Mode (Auto-park Recording)
2.7 Manual Mode (User-defined Recording)
2.8 File Management & Capacity
2.9 Situational Operation & Notification
2.10 Firmware Update
2p
5p
6p
7p
8p
3.1 Program Settings
3.2 Display Configuration
3.3 Operating Instructions
15p
17p
18p
9p
9p
9p
9p
10p
10p
11p
11p
12p
14p
19p
20p
Table of
Contents
Product Specifications
PC ViewerGeneral Information
Basic Operations Customer Support
Product Warranty
The information in this document, hardware and software versions are subject to change without
notice and should not be construed as a commitment by Unavi USA, Inc. Unavi assumes no
responsibility for any errors that may appear in this document.
NOTICE

2
General
Information
1.1 Important
Safeguards and
Disclaimers
● In no event shall Unavi be liable for incidental or consequential damages arising from use of this
document or the hardware and software described in this document. Photos are non-binding. The
manufacturer and importer do not take responsibility for any printing errors.
● For your safety, please do not operate this unit while driving. Be sure the vehicle is at a complete
stop and parked in a legal manner when operating this unit. As a driver you are solely responsible
for your road safety.
● This product is an in-dash mount video recording device. Recording may fail depending on the given
situation.
● This product must be used only with manufacturer’s approved parts and accessories. If not, any
warranty claims can be denied.
● If this product is damaged and/or disconnected from power due to a collision, the product may not
operate properly and fail to record videos.
● Unavi and any of its affiliates are not responsible for any accidents pertaining to the misuse of this
product during inappropriate times.
● All hardware and software belong to and are the property of Spire Technolgy. Duplication and/or
distribution or duplications of any copyrighted materials are illegal and may result in criminal penalties
and civil lawsuits. Any unauthorized attempts to access, upload or change any information to defeat or
circumvent security features may be subject to criminal penalties and civil lawsuits. Utilization of this
product for any other use than its intended purpose is prohibited. Contravention will be prosecuted.
● The trademark and the UREC™ logo are owned by Unavi USA, Inc. Any other trademarks and
commercial names belong to and are the property of their respective owners.

3
General
Information
1.1 Important
Safeguards and
Disclaimers
● Do NOT manually operate this product while driving!
● Any responsibility for product failure resulting from user’s lack of care, or injuries or damages
caused to the product while driving is disclaimed.
● For product’s optimal operation and memory use, format memory at least once every two weeks
-- Product may not operate normally if used without formatting the memory for an extended period
of time.
● Excessive window tinting may deteriorate video recording quality, or images may appear dark.
● It is highly recommended that the front and/or rear windshields be kept clean and free from dust to
guarantee the most optimal recording quality.
● As the product records moving images using a camera lens, images taken under certain light
conditions may be of interior quality (e.g. sudden changes in brightness, extreme backlight of sun
during midday, conditions in which there is no light, etc.).
Operation
● Make sure vehicle is turned off before installation.
● Place the product safely out of reach of children and pets at all times.
● Do not install in a location that interferes with driving and visibility.
● When mounting this product, remove dust, impurities, moisture and foreign substances to ensure
firm attachment.
● After the MicroSD Card is inserted, connect power cord to the DC-IN jack.
● Relocating the product may result in a change of the viewing angle. Adjust the angle after installing
the product and preview the recorded videos.
Installation

4
General
Information
1.1 Important
Safeguards and
Disclaimers
● Do not attempt to disassemble or tamper with the product at your discretion as it may cause
product malfunction, electric shock, loss of recorded data, and warranty to be voided. Do not apply
excessive force, shock, or vibration to the product.
● Storing this product in a humid or dusty location may result in product malfunction or failure.
● Do not wipe the product using liquid chemicals or detergents; use dry microfiber cloth to clean the exterior.
● Prevent liquid or objects of any kind from entering the product and cable. If liquid is spilled or
foreign matters are seeped into the product, disconnect power immediately.
● Do not cover up product with a towel or cloth-like material. Increased internal temperature may
cause product to malfunction or become a fire hazard.
● Normal operating temperature is between -4°F ~ 140°F. Long-term exposure and extended use of
this system outside of the operating temperature can cause the system to malfunction.
● If you notice any strange odors from the cigarette jack, stop using product and contact where it was
originally purchased. Also, do not use damaged cigarette lighter plug cables and do not handle it
with wet hands.
● If the vehicle is expected to be parked for an extended period of time, disconnect power from the
product to prevent battery drainage and/or electric discharge.
Care & Maintenance
● Never remove the MicroSD card while the product is in operation or firmware upgrade is in progress,
as doing so may damage the SD card and will be ineligible for warranty replacement.
● To remove MicroSD Card, unplug power cable at the top of device, wait 30 seconds and check to be
sure that LED is powered off before removing SD card.
● Make sure to create backup files as necessary.

General
Information
5
1.2 Features ● Supports 720p HD resolution (1280 x 720 pixels)
● Recording lens angle of up to 120° wide @ 30
frames per second
● 2-mega pixel camera equipped with image sensor
● Continuous, real-time recording of audio and video
● 4 recording modes (Normal, Event, Manual and Parking)
● Supports 2 channels to add an additional camera
for the rear windshield
● Built-in motion detection & 3-axis accelerometer
(G sensor)
● Automatic memory deletion and built-in MicroSD
card format functions
● Built-in microphone for high-quality audio that
records simultaneously with video
● Portability and expandable memory capacity using
MicroSD Card
● Easy viewing of recorded video files using the
exclusive PC Viewer program
● Ability to set accelerometer sensitivity through
PC Viewer
● Video output for viewing images through an external
monitor
● One-touch buttons, voice alerts and LED indicator
lights to enhance convenience of user operations
● Built-in backup battery & RTC (Real-Time Clock) module
● Built-in low voltage blocking system that prevents
car battery drainage (can be set or modified in PC Viewer)
● Adjustable mount for ease of use and positioning
● The recording features of this product are not affected by GPS signal reception.
● If this product is trying to acquire satellite signals for the first time, it may take longer than normal to
establish an initial position. If the unit is powered on and outdoors with a clear view of the sky, this
process should not take more than 5-10 minutes.
● If the vehicle is left non-operational for an extended period of time, the GPS memory data may have
been drained and will require at least 15 minutes of warming up to function properly.
● Atmospheric conditions such as rain and fog can cause the GPS signal to fail. Driving inside tunnels, in
between tall buildings, and highly populated areas can also interfere with and diminish GPS signal reception.
● If your vehicle has a protective UV coating on its windshield and has any electronic devices that
require sate-llite signals, it may prevent your GPS from operating properly.
● Depending on the location of the GPS receiver/antenna, temporary degradation in reception
performance is also possible. GPS reception rate may not be identical for all vehicles.
GPS The GPS feature for this product may not be supported certain countries.
1.1 Important
Safeguards and
Disclaimers

Windshield mount
& Double-sided tape
Rear Camera
(Optional)
External GPS &
Wi-Fi USB dongle
(Optional)
Front Camera (Main Unit)
Product
Documentation
MicroSD CardCigarette lighter
power supply cable
General
Information
1.3 Components &
Accessories
User
Manual
If you have problems with any of
the provided components, please
contact the original place of
purchase.
Components provided and those
sold separately are subject to
change at any time without prior
notice.
Optional components/features may
not be available for use in every
country.
6
OBD-II port
power supply cable
(Optional)

Adjustable mount
Front security LED indicator
Camera recording lens
SERIAL No.
One-touch buttons
(Record button & Mute On/Off)
Recording status LED indicator
GPS status LED indicator
Power supply port
Video output port
External GPS port
Wi-Fi USB dongle port
1.4 Component Identification
● FRONT ● REAR
● TOP
Wi-Fi USB dongle
(Optional)
General
Information
If you have problems with any of
the provided components, please
contact the original place of
purchase.
Components provided and those
sold separately are subject to
change at any time without prior
notice.
Optional components/features may
not be available for use in every
country.
7

General
Information
1.5 How to install
1. Insert MicroSD Card
(ensure it is properly inserted in the right direction)
2. Wipe dust, impurities and moisture from windshield surface and mount the front camera.
An ideal location to install the product is behind the rearview mirror, also using it as a reference
point to center align viewing angle of the camera lens.
3. Connect power cable to the DC-IN port and plug in the other end to the cigarette lighter jack.
4. Adjust position of the product mount as you see fit.
Then keep all cables neat and concealed as much as possible.
How to install
8

Basic
Operations
2.1 Connecting Power
& Starting Up
2.2 Disconnecting
Power &
Shutting Down
● When the unit is powered on or the vehicle is started up, you will hear a voice message, “Hi,
this is UREC” and “Constant recording on.” This indicates the product is starting to record.
● A few moments after the unit is powered off or the engine is turned off, you will hear “Video
recording off” followed by “System is shutting down,” after which the product will turn off.
2.3 Safe Mode ● If UREC has prolonged exposure to high temperatures, it will automatically enter ‘safe mode’
to prevent overheating. Once surrounding temperatures are decreased, UREC will return to
normal operating mode.
2.4 Constant Mode
(Normal Recording)
● Normal recording begins with the introduction, “Constant recording on.” Video captures from
the Constant Recording mode are available in the “NORMAL” folder of the MicroSD Card root
directory.
● Constant recording video capture files are saved in the following format:
Video files in this mode are recorded and playable in 1-minute interval (Recording time may be shortened
when the Event Recording mode overrides).
Channel_File Number_Save Date_Save Time (Hour, Minute, Second)_Save Time (Hundredths of a Second)_
File Size_Recording Mode
(e.g. ch1_0001_20130430_085126_874_31142_N)
9

Basic
Operations
2.5 Event Mode
(Impact Recording)
● When the accelerometer (G sensor) detects an unusual impact, video captures are saved in a
separate folder labeled “EVENT” in the MicroSD Card root directory.
● A chime will accompany files being saved under the Event Recording mode.
● When Event Recording mode begins, video captures in progress under Constant Recording
mode will end.
● Event recording video capture files are saved in the following format:
Each Event video capture file will be 12-13 seconds long (10 seconds before impact to 2-3 seconds after impact).
2.6 Parking Mode
(Auto-park Recording)
● If there are no changes to the G sensor for approximately 10 minutes, Constant Recording
mode switches to Parking Recording mode. Video captures in Parking Recording mode are saved
to a folder labeled “PARKING” in the MicroSD Card directory.
● Parking Recording mode video capture files are saved in the following format:
Video files in this mode are recorded and playable in 25-second interval (Recording time may be shortened
when the Event Recording mode overrides).
Channel_File Number_Save Date_Save Time (Hour, Minute, Second)_Save Time (Hundredths of a Second)_
File Size_Recording Mode
(e.g. ch1_0001_20130430_085126_874_31142_P)
Channel_File Number_Save Date_Save Time (Hour, Minute, Second)_Save Time (Hundredths of a Second)_
File Size_Recording Mode
(e.g. ch1_0001_20130430_085126_874_31142_E)
10

Basic
Operations
2.7 Manual Mode
(User-defined
Recording)
● Manual recording is for recording some situation arbitrarily.
● Manual recording begins when the Camera button is pressed once. Manual Recording will begin
with the introduction, “Manual recording ON.” Files saved while in Manual Recording mode can be
found in a folder labeled “Manual” in the SD card.
● Manual Recording mode video capture files are saved in the following format:
Video files in this mode are recorded and playable in 20-second interval on average.
2.8 File Management
& Capacity
● If the allotted mode-specific memory capacity is exceeded, old files are deleted and replaced
with newly recorded videos.
● As recorded video files in the MicroSD Card may be deleted in a short period of time depending
upon its memory capacity, it is highly recommended to save important files in an external
storage device.
● File capacity for each recording mode based on 2-channel recording (and 1-channel):
Channel_File Number_Save Date_Save Time (Hour, Minute, Second)_Save Time (Hundredths of a Second)_
File Size_Recording Mode
(e.g. ch1_0001_20130430_085126_874_31142_M)
Event Mode 40(80) Files 80(160) Files 160(320) Files
Manual Mode 10(20) Files 20(40) Files 40(80) Files
Parking Mode
Constant Mode
40(80) Files 80(160) Files 160(320) Files
8GB 16GB 32GB
Remaining storage (after saving Event, Manual & Parking recording modes)
Recording
Mode
Memory
11

Voice Alert
Voice Announcement and LED Notifications
Status
/ Function Operating Mode
“Hello, this is UREC.”
Boot-up
Firmware
update
Copy update files onto
the SD Card using a
PC and insert it back
into UREC
While UREC is
powering up
Constant
/ Normal recording
While vehicle is
in motion
Improper
SD Card
removal
Missing
SD Card
SD Card
detected
Event recording
Manual
Recording
Built-in
formatting mode
(SD Card format)
Mute settings
(Turn audio
recording on/off)
Video output
(Connect UREC to
external monitor)
“Update in progress.”
“Please do not power off until
update is complete.”
“Update complete.”
“Constant recording on.”
“SD Card has been
removed abnormally.”
(Recording ends and
device turns off)
“SD Card is missing or not
recognized.”
“Please insert SD Card.”
“System is shutting down.”
“Voice recording on.” or
“Voice recording off.”
(Chime)
(Chime)
“Manual recording on.”
“Preparing to format SD Card.”
“Please press the recording
button again within 5 seconds.”
When SD Card is
ejected
while in use
When SD Card is not
detected or inserted
properly
When SD Card is
inserted while
device powered on
When abnormal impact
is detected by UREC
To activate, press ‘record’
button once briefly during
constant recording mode
To activate, press ‘record’
button and hold for
at least 3 seconds
When the ‘microphone’
button is briefly pressed
once
To activate, press ‘record’
button and hold for
at least 3 seconds
On On On
Light flashes
rapidly
Light flashes
rapidly
Light flashes
rapidly
On
OnOff
Front LED REC LED GPS LED
Light flashes twice
per 1 second
Light flashes twice
per 1 second
Depends on
GPS status
On Light flickers
per 1 second
Depends on
GPS status
Light flickers
per 1 second
Depends on
GPS status
Depends on
GPS status
Light flickers per
2 seconds
Light flickers per
2 seconds
Light flickers per
2 seconds
Light flickers per
2 seconds
Depends on
GPS status
Flickers per
0.5 second
Flickers per
0.5 second
Depends on
GPS status
Flickers per
0.5 second
Flickers per
0.5 second
Depends on
GPS status
Depends on
GPS status
Light flickers per
2 seconds
Light flickers per
2 seconds
Depends on
GPS status
2.9 Situational
Operation &
Notification
Basic
Operations
12

Voice Alert
Voice Announcement and LED Notifications
Status
/ Function Operating Mode
“Switching to parking mode.”
Constant
recording mode
switches to →
Parking
recording mode
Auto-Parking
recording mode
(Motion detection)
Activates while vehicle
is parked when UREC
detects external
movement in a
general area around
the vehicle
Activates when vehicle
is in idle state for
5-10 minutes during
constant recording
mode
Preparing for
parking recording
mode
(Parking standby)
When in parking standby
mode, UREC does
not detect
external movements
around the vehicle
Parking
recording mode
switches to →
Constant
recording mode
GPS normal
operation
Device shutdown
after normal
operation
(Chime)
----
----
“Switching to recording mode.”
“Video recording off.”
“System is shutting down.”
When vehicle starts to
move; or when the
‘record’ button is
pressed once during
parking mode
When GPS 3D Fix
is applicable
When UREC is
powered off
Light on for
3 seconds Off
Depends on
GPS status
Flickers per
0.5 second
Flickers per
0.5 second
On
Off Off Off
Front LED REC LED GPS LED
Light on for
3 seconds Off Depends on
GPS status
Depends on
GPS status
Flickers per
0.5 second
Flickers per
0.5 second
Depends on
GPS status
Depends on
GPS status
Depends on
GPS status
2.9 Situational
Operation &
Notification
Basic
Operations
13

2.10 Firmware Update ● When required, firmware updates can be done when the upgrade files are saved to the MicroSD
Card. Upgrade files are available for download at www.unavi-usa.com.
● The update procedure will begin with the following voice message: “Update in progress. Please
do not power off until update is complete.”
● Upon completion you will be notified with a voice message, “Update complete” after which you
can resume using UREC normally.
Basic
Operations
14

3.1 Program Settings
PC Viewer
● UREC-recorded video captures can be viewed on a PC via PC Viewer. The PC Viewer installation
file is available for download at www.unavi-usa.com.
● Minimum System Requirements for PC Viewer:
Download
Operating Conditions
Video : If using 2-channel 720p HD (Front/Rear 1280x720)
Audio : 1-channel (PCM, 16bit, 16KHz)
Rate : 1x speed play
Hardware Specification
CPU : Intel Dual-Core 2.8 GHz
RAM : 2 GB
Video Card : 256 MB
Monitor : 1280 x 720 resolution
Software Specification
Operating System : Windows XP SP2 (32 bit) / Windows Vista (32 bit) / Windows 7
DirectX 9.0
Other Information
For fast forward play, frame rate options can be configured in the program settings.
When PC performance does not meet the required speed, the maximum possible frame rate will be used.
Playback speed may be slow in case of low CPU performance.
During display, D3D9 (Direct 3D v9) is used by default. However, if the video card does not support
DirectX 9.0, DDraw (Direct Draw) will be used instead. Please be advised that when DDraw is used, the
zoom function is unavailable.
15

3.1 Program Settings
PC Viewer
● Please download the PC Viewer installation file from www.unavi-usa.com. After installation, run
the BBViewer.exe file and PC Viewer will be available for use.
● Press the F1 key on your computer for further instructions on how to use the program.
● If an error occurs during installation or while the program is running, please update the PC’s
Windows O/S to the latest version. Then, reinstall or re-run the program.
The UREC PC Viewer icon will
appear on your desktop.
16

3.2 Display
Configuration
PC Viewer
Remove MicroSD Card from UREC
and connect to your PC using a
plug-in adapter.
⑧
①Playback screen
② File List : Displays file(s) retrieved from the SD card; Select desired file and double-click on
the item or press Play to view recorded video captures.
③ Map : Indicates location of video capture
④ Screen : Play Previous file, Play Backward, Pause, Stop, Play, Play Next file
⑤Impact Sensor : Sensitivity of impact occurred during regular driving and parking
⑥GPS Speed : Recorded speed while driving
⑧Settings / Additional Support
⑦File Open : Retrieve files stored in computer
SD Selection : Lists recorded video capture folders and files stored in the directory
Driving Record : Details of driving records by date are available
*Warning: PC Viewer will not be able to detect the SD Card drive if MicroSD Card is blank and/or has never
been used before. Insert MicroSD Card into UREC and allow for saved video captures prior to using
PC Viewer.
17
Table of contents