Ursalink UC1 14 Series User manual

1
UC1X14 Series
SMS Remote I/O
Quick Start Guide

www.ursalink.com
1
Welcome
Thank you for choosing Ursalink UC1x14 series SMS remote I/O.
This guide describes how to install the UC1x14 series SMS remote I/O.
Once you complete the installation, refer to the Ursalink UC1x14 User Manual for instructions on how to
perform configurations on the device.
Related Documents
This Start Guide only explains the installation of Ursalink UC1x14 series SMS remote I/O. For more
functionality and advanced settings, please refer to the relevant documents as below.
Document
Description
Ursalink UC1x14 Datasheet
Datasheet for the Ursalink UC1x14 series SMS remote I/O.
Ursalink UC1x14 User Guide
Users could refer to the guide for instruction on how to configure
all the settings.
The related documents are available on Ursalink website: http://www.ursalink.com.
Declaration of Conformity
Ursalink UC1x14 series SMS remote I/O is in conformity with the essential requirements and other relevant
provisions of the CE, FCC, and RoHS.
For assistance, please contact
Ursalink technical support:
Email: [e-mail]
Tel: [phone]
Fax: [phone]

Ursalink UC1x14 Quick Start Guide
www.ursalink.com
2
Before you begin to install the UC1x14 series SMS remote I/O, please check the package contents to verify
that you have received the items below.
1.1 Package Contents
1 × UC1x14 Series
Device
1 × Stubby
Cellular Antenna
1 × 12-Pin Pluggable
Terminal
1 × Warranty Card
Setscrews
Optional Accessories
If any of the above items is missing or damaged, please contact your Ursalink sales
Representative.
2.1 Overview
A. Front Panel
1 × Power Adapter
(Optional)
1 × Magnetic Mount
Cellular Antennas
(Optional)
1. Packing List
2. Hardware Introduction
1LED Indicator Area
System: System Indicator
ACT: Network Indicator
2Cellular Antenna Connector
3Micro USB Interface

Ursalink UC1x14 Quick Start Guide
www.ursalink.com
3
B. Rear Panel
2.2 Dimensions (mm)
2.3 Pinouts
PIN
Power
Digital Input
Relay Output
Description
1
GND
---
---
DC power supply (-)
2
VIN
---
---
DC power supply (+)
3
---
IN1
---
Input1
4
---
IN1_COM
---
Common Ground
5
---
IN2
---
Input2
6
---
IN2_COM
---
Common Ground2
7
---
---
OUT1_COM
Common Ground
8
---
---
OUT1_NC
Normally Closed1
9
---
---
OUT1_NO
Normally Open1
10
---
---
OUT2_COM
Common Ground
11
---
---
OUT2_NC
Normally Closed2
12
---
---
OUT2_NO
Normally Open2
112-Pin Pluggable Terminal

Ursalink UC1x14 Quick Start Guide
www.ursalink.com
4
2.4 LED Indicators
LED
Indication
Status
Description
System
System Status
Solid On
Equipment starts
On for 500ms, off for 500ms
All OK
On for 100ms, off for 100ms
Device can not send SMS
ACT
Network Status
Off
Network registration fails
On for 75ms, off for 3000ms
Successfully registered on network
Sending/Receiving SMS
Environmental Requirements
- Power Input: 5-24 VDC
- Operating Temperature: -40°C to 70°C (-40°F -158°F)
- Relative Humidity: 0% to 95% (non-condensing) at 25°C/77°F
3.1 SIM Card Installation
3. Hardware Installation
A. Unscrew the four screws in front panel of
the device
B. Takeout mother board from the case.
C. Push-down the SIM card cover and lift the
cover
D. Install SIM card and close the sim card cover

Ursalink UC1x14 Quick Start Guide
www.ursalink.com
5
3.2 Antenna Installation
Rotate the antenna into the antenna connector accordingly.
The external cellular antenna should be installed vertically always on a site with a good cellular signal.
3.3 Connect the UC1x14 to a Computer
E. Re-install the mother board into the case

Ursalink UC1x14 Quick Start Guide
www.ursalink.com
6
3.4 Mount the UC1x14
Use 2 pcs of flat head Phillips screws to fix the UC1x14 onto the wall mounting.
4.1 Configure UC1x14 via Toolbox
Please connect PC USB port to micro USB port of UC1x14 series SMS remote I/O directly, PC Setup the
Toolbox.
4. Confiure UC1x14
①Select Serial port and fill in the login password, default “123456”, then click “Save”

Ursalink UC1x14 Quick Start Guide
www.ursalink.com
7
②Click “ ” to check status of the Remote I/O
③Click “ ”, network type use Auto and configure the SMS center number of the SIM card

Ursalink UC1x14 Quick Start Guide
www.ursalink.com
8
④Click “ ” configure the IF&THEN commands.
⑤Click “ ” to configure the IF&THEN commands and click “ ”, check details of the
commands in user manual

Ursalink UC1x14 Quick Start Guide
www.ursalink.com
9
⑥Click “ ” to save the command into UC1x14
⑦Click “ ” to read the commands configured in the UC1x14

Ursalink UC1x14 Quick Start Guide
www.ursalink.com
10
[END]
⑧Click “ ” to configure the SMS control phone center number and SMS report phone
number, then click “Save”