UTAH SCIENTIFIC UTAH-100 UDS-288 User manual

UTAH-100/UDS 288
System Setup and Operation Guide

ii
UTAH 100/UDS 288x288 Operations Guide
• Document Number: 82102-0079
• Document Version: 1.3
• Date: March 21, 2016
• Printed in U.S.A.
Copyrights and Trademarks
© 2016 Utah Scientific, Inc., All rights reserved. Any use or reproduction of this
guide’s contents without the prior written consent of Utah Scientific, Inc. is
strictly prohibited.
•UTAH 100 is a trademarks of Utah Scientific, Inc.
•Windows, Windows 2000 and Windows NT and XP are registered trademarks
of Microsoft Corporation.
•All other product names and any registered or unregistered trademarks men-
tioned in this guide are used for identification purposes only and remain the
exclusive property of their respective owners.
Notice
Information contained in this guide is subject to change without notice or
obligation. While every effort has been made to ensure that the information is
accurate as of the publication date, Utah Scientific, Inc. assumes no liability for
errors or omissions. In addition, Utah Scientific, Inc. assumes no responsibility
for damages resulting from the use of this guide.
FCC Compliance (USA) and Digital Equipment Com-
pliance (Canada)
This equipment has been tested and found to comply with the limits for a Class
A, digital device, pursuant to Part 15, Subpart B of the FCC Rules and the
Canadian EMC Requirement (ICES-003). These limits are designed to provide
reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.

iii
Section 1
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case, the user will be required to correct the interference at their
own expense. Shielded cables must be used to ensure compliance with the FCC Class
A limits.

iv
Declaration of Conformity
Utah Scientific, Inc.
4750 Wiley Post Way, Suite 150
Salt Lake City, Utah 84116-2878 U.S.A.
We declare our sole responsibility that the UTAH-100/UDS Digital Routing
Switcher is in conformance with the following standards:
Emission
•EN55022:1994+A1&A2
Immunity
•EN55024:1998
•EN61000-3-2
•EN61000-3-3
Safety
•IEC 60950-1:2001 /EN 60950-1:2001
Following the provisions of the Directive(s) of the Council of the European
Union:
•EMC Directive 89/336/EED
•Low Voltage Electrical Directive 72/23/EEC
Utah Scientific, Inc. hereby declares that the product specified above conforms to
the above Directive(s) and Standard(s).

v
Section 1
Important Safeguards and Notices
This section provides important safety guidelines for the Operator and Service
Personnel. Specific warnings and cautions are found throughout the guide where they
apply, but may not appear here. Please read and follow the important safety
information, specifically those instructions related to risk of fire, electric shock, or
injury to persons.
Safety Symbols
•Hazardous Voltage symbol
•Caution symbol. The product is marked with this symbol
when it is necessary to refer to the manual to prevent damage
to the product.
Warnings
Please observe the following important warnings:
•Any instructions in this guide that require opening the chas-
sis, changing a power supply, or removing a board, should be
performed by qualified personnel only. To reduce the risk of
electric shock, do not perform any service unless you are
qualified to do so.
•Heed all warnings on the unit and in the operating instruc-
tions.
•Do not use this product in or near water. Disconnect AC
power before installing any options or servicing the unit
unless instructed to do so by this manual.
•This product is grounded through the power cord ground con-
ductor. To avoid electric shock, plug the power cord into a
properly wired receptacle before connecting the product
inputs or outputs.
•Route power cords and other cables so they won’t be dam-
aged.
•The AC receptacle (socket) should be located near the equip-
ment and be easily accessible.
•Disconnect power before cleaning. Do not use any liquid or
aerosol cleaner - use only a damp cloth.