UTEPO UTP7201GE-PSE60 User manual

Board Diagram
Please follow installation steps as below
Please check the following accessory, if you find the item lost, please contact our local
dealer.
PoE Injector 1pc
AC Power Cable 1pc
Power Buckle 1pc
User Manual 1pc
(1) Turn off the system's power before the installation;
(;
(3) The Data Input of this injector is connected with switch of no PoE fuction;
(4) Please connect PoE Injector with AC cable;
(5) Please examine and power the system.
2) The PoE Output port of this injector is connected with PoE IP Camera
Installation
This is a single-port PoE injector with one Ethernet port, one PoE output port, and one AC
input power port. It supports end-span PoE and the output power consumption is up to 60W; It
features:10/100M/1000Mbps network,100m transmission distance,6KV lightning protection,
industrial-level chip, and patent alert. it's an excellent choice for power supply and network
transmission on PTZ cameras, all-in-one PC, digital display system.
Features
12
Front
Back
Notice
The transmission distance depends on the signal source and cable quality,standard
Cat5e/6 cable is strongly suggested for reaching the maximum transmission distance!
Bayonet
Application
Cat5/5e/6 Cable
Monitor
NVR
PoE IP camera
PoE IP camera
PoE IP camera
Ethernet Switch
PoE Injector
PoE IP camera
PoE Injector
●
● Ultra PoE、IEEE 802.3af/at、IEEE 802.3 10Base-T/100Base-TX/IEEE802.3ab 1000Base-T;
● Higher conversion efficiency(90%); Lower heat radiation;
● Working Temperature: -10℃～55℃;
● 6KV lightning protection; 8KV ESD;
● No fan, no noise, dustproof;
● LEDs indicate operation status.
PoE++ power supply standard; Output power consumption up to 60W;
PoE Injector(Gigabit/60W)
User Manual VerB 1.0
Connection Bayonet
Bayonet Bayonet
Input power indicator Output PoE indicator

连接 接口
Specification
Item
Description
Interface
Input Voltage
AC100V~AC240V
Data Input
1×RJ45
PoE output
1×RJ45
PoE
PoE Power Supply Type
End-span/Mid-span
PoE Power Output
DC 54V/60 watts
Output Ripple
＜5%
Power Pin Assignment
Pair1:1/2(+),3/6(-) Pair2:4/5(-),7/8(+)
Ethernet Port
Communication Port
1×RJ45 Input
TransmissionRate
10/100/1000Mbps
Transmission Medium
Cat5/5e/6 Cable
Distance
100m (Max.)
Status
Power LED
1 (Red)
PoE LED
1 (Orange)
Protection
Surge Protection
P Power：1KV(Differential Mode),2KV(Common
Mode)1.2/50us，8/20us
Ethernet：2KV(Differential Mode),6KV(Common
Mode)10/7000us
oE
ESD
1a Contact Discharge Level 3
1b Air Discharge Level 3
Per: IEC61000-4-2
Environment
Working Temperature
- ℃10 ~55℃
Storage Temperature
-40 ~85℃℃
Humidity(Non-condensing)
0~90%
Mechanics
Dimension(LxWxH)
160mm×64mm×60mm
Material
ABS Plastics
Color
Black
Weight
200g
Product specifications subject to change without prior notice
34
Instruments to be used: wire crimper, network tester. Wire sequence of RJ45 plug should
conform with EIA/TIA568A or 568B.
1) Please remove 2cm long the insulating layer, and bar the 4 pairs UTP cable;
2) Separate the 4 pairs UTP cable and straighten them;
3) Line up the 8 pieces of cables per EIA/TIA 568A or 568B;
4) Cut off the cables to leave 1.5cm bare wire;
5) Plug 8 cables into RJ45 plug, make sure each cable is in each pin;
6) Use the wire crimper to crimp it;
7) Repeat above 5 steps to make the another end;
8) Using network tester to test the cable whether is working.
RJ45 Making Method
pin color
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
1
2
3
4
5
6
7
8
pin color
1
2
3
4
5
6
7
8
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
EIA/TIA 568A EIA/TIA 568B
When choose RJ-45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
When choose RJ-45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
Notice
PoE Injector
Trouble Shooting
If any trouble in installation, please follow these steps
Please make sure you have followed the instruction to install the device;
Please confirm if the RJ45 cable order is in accordance with the EIA/TIA 568A or 568B
industry standard;
The power supply of PoE port is no more than 30W; please do not connect the network device
whose power consumption is over 30W;
Please replace a failure device with a proper one to check if the device is broken;
If the problem still exist, please contact the local dealer.
PoE Injector