UVI Chair STYLER User manual

1
Assembly guide for UVI chair STYLER | DEVIL | BACK IN BLACK
Congratulations on purchasing your very own UVI chair, which will make sure you are sitting correctly
and comfortably. Below you will find the guide for correct assembly and proper usage. For proper
assembly of the chair, please follow the instructions carefully.
The following assembly guides apply to the following models:
UVI Chair STYLER
UVI Chair DEVIL
UVI Chair Back in Black
Contents of the package
1. support pillow for your back
2. support pillow for your head
3. side caps
4. wheels
5. chair legs
6. back rest
7. gas spring
8. gas spring cover
9. gas spring control mechanism
10. bottom rest
11. arm rests
12. not pictured: screws, tool, hole covers…

2
Assembly guide for UVI chair STYLER | DEVIL | BACK IN BLACK
Screws –specification
A. screw key
B. bolt M8 x25 (longer)
C. bolt M8 x20 (shorter)
D. plain washer
E. spring washer
F. plastic cover for holes (3)
Assemble all screws in this order: First E (spring washer) then D (plain washer). This will ensure that
the screws don’t get loose. Please, apply reasonable strength.
Chair assembly guide
Estimated time to assemble this chair is about 30 minutes. You can do it on your own, but we advise
you to get some help to make things easier.
To avoid unnecessary problems, please read the whole guide before assembling.
All the tools and screws are supplied. Only use the screws that are in the package!
To avoid damage and tearing after prolonged use, all the holes are thermally treated. Please clean the
holes before tightening the screws (pictured in step 3)
After completing the assembly, we recommend you to wipe the chair with a damp cloth. If you notice
stains left from the manufacturing process, you may want to use a leather cleaning product, which
must be applied to a cleaning cloth and not directly to the chair

3
Assembly guide for UVI chair STYLER | DEVIL | BACK IN BLACK
Step by step assembly
STEP 1
Insert wheels (4) into the chair legs (5). For easier insertion wiggle the wheels left and right until they
slide in the hole. Do NOT hit the wheels!
STEP 2
Insert the gas spring (7) into the chair legs (5) and cover the gas spring with the cover (8).

4
Assembly guide for UVI chair STYLER | DEVIL | BACK IN BLACK
STEP 3
Clean all the screw holes. The holes are thermally treated to prevent damage and tearing after
prolonged use. Before inserting the screw, please clean all the holes by inserting the tool, bending it at
an angle and spinning it around the hole.
STEP 4
Attach the gas control mechanism (9) to the bottom plate (10). On the control mechanism, you will
find the word FRONT and an arrow pointing forward. Turn the mechanism, so that the FRONT sign is
facing the front part of the chair. Use the shorter screws M8x20mm (Shorter, C). Please, apply
reasonable strength.

5
Assembly guide for UVI chair STYLER | DEVIL | BACK IN BLACK
STEP 5
Attach the arm rests (11) to the bottom plate (10). Use the longer screws M8x25mm (B).
STEP 6
Place the bottom plate (10) on the gas spring (7). Please make sure that it fits together nicely.

6
Assembly guide for UVI chair STYLER | DEVIL | BACK IN BLACK
STEP 7
Place the back plate (6) on the bottom plate and secure it with the side screws M8x25mm (longer, B).
First, screw all of them half way, then till the end. Please, apply reasonable strength.
STEP 8
Attach the side covers (3) to the side mechanism. Start by pushing the lower part into the hole so it
locks, then screw the upper side with the screw for the cover plastic (F). On the inner side of the cover,
L (left side) and R (right side) are indicated and they mark the side where each of the two covers should
be applied. At last, apply the hole covers.

7
Assembly guide for UVI chair STYLER | DEVIL | BACK IN BLACK
STEP 9
If you wish, you can install the support pillows (2 and 1). The smaller support pillow for the head (1)
has a band that you simply place at the head area of the chair. The bigger lower pillow can be fitted by
placing the bands between the bottom and back plates and clipping them at the back. For easier
installation, push the sitting foam downward and push the band through with the other hand.
Congratulations, you have successfully assembled your own UVI chair. In case you need any
additional information, please can contact us via email inf[email protected]om or this mobile number 00
386 70 388 288. We will be happy to help you.

8
Assembly guide for UVI chair STYLER | DEVIL | BACK IN BLACK
Usage instructions
All UVI chairs have the original memory foam which will adapt to your body after the first few hours of
usage. Because of this, sitting can be uncomfortable at the beginning.
All the chairs that have the 180 degrees inclination are perfectly safe to use. Our bodies are not used to
this position, so they can have a reflexive response to it. We recommend you to lower the chair to this
position gradually, so your body can adapt.
All our chairs are made to carry the maximum allowed weight. If you use the chair improperly, damage
to it or to you may occur. Jumping, hanging and similar activities are, of course, not advised.
You can adjust the height, back rest and tilt of your UVI chair.
-Adjust the height by using the handle under the seat (on the right side).If you want your chair
to go higher, please get off of the chair, and if you want to lower the position, simply sit on it.
-On the right, you will find the handle that adjusts the angle of the back rest. You can adjust the
angle by lifting the handle. When rising it, please hold the back rest to prevent it from striking
you.
-Under the seat is the round button which controls the tilt of the chair. You can turn it left or
right to get the desired tilt. If you do not want your chair to tilt, please push the handle (for
height control) to the left or right. This will disable the tilt function of the chair.
Important!
Never seat at the end of the chair! Try to sit as straight at the middle of the chair as possible with
your shoulder blades touching the back of the chair. We highly advise the use of the head pillow. The
lower pillow might not feel right to all users. In case you cannot get used to it, we advise you to
remove it as it may cause you to lose focus while gaming/working.
Warning!
Don’t seat at the end of the chair as it may tip over if you do so. Sit in the natural posture. We also
highly recommend you NOT TO cross your legs when sitting.