V-tech t 2435 User manual

1
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury, including the
following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for example, near a bath tub, kitchen
sink or swimming pool).
5. Do not place this product on an unstable surface, such as a table, shelf, or
stand. The product may fall, causing serious damage.
6. Slots and openings in the back or bottom of the Base Unit and Handset are
provided for ventilation. To protect them from overheating, these openings
must not be blocked by placing the product on a soft surface such as a bed,
sofa or rug. This product should never be placed near or over a radiator or
heat register. This product should not be placed in any area where proper
ventilation is not provided.
7. This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply in your
home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not install this product
where the cord may have anyone walking on it.
9. Never push objects of any kind into this product through slots in the Base or
Handset as they may touch dangerous voltage points or short out parts that
could result in a risk of fire or electric shock. Never spill liquid of any kind on
the product.
10.To reduce the risk of electric shock, do not disassemble this product, but
take it to an authorized service facility. Opening or removing parts of the
Base or Handset other than specified access doors may expose you to
dangerous voltages or other risks. Incorrect reassembling can cause
electric shock when the product is subsequently used.
11.Do not overload wall outlets and extension cords as this can result in the
risk of fire or electric shock.
12.Unplug this product from the wall outlet and refer servicing to an authorized
service facility under the following conditions:
A. When the power supply cord or plug is damaged or frayed.
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM1

2
Important Safety Instructions
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions, as improper adjustment of other controls may result in
damage and often requires extensive work by an authorized technician
to restore the product to normal operation.
E. If the product has been dropped and the Base and/or Handset has been
damaged.
F. If the product exhibits a distinct change in performance.
13.Avoid using a telephone (other than cordless) during an electrical storm.
There is a remote risk of electric shock from lighting.
14.Do not use the telephone to report a gas leak in the vicinity of the leak.
15.Only put the Handset of your telephone next to your ear when it is in normal
talk mode.
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM2

3
Enhanced 2.4GHz Technology - Dual Band transmission combines the best of 2.4GHz
and 900MHz technologies, providing enhanced performance over standard cordless
telephones.
Before You Begin
6. Battery Packs
7. Belt Clips
8. User’s Manual
9. Charger AC Power Adaptor
10.Base Wall Mounting Bracket
To purchase replacement batteries, call VTech Communications, Inc. at
1-800-595-9511. In Canada, call VTech Telecommunications Canada Ltd. at
1-800-267-7377.
Parts Check List
1. Base Unit
2. Handsets
3. Handset Charger
4. Base AC Power Adaptor
5. Telephone Line Cord
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM3

4
Getting Started
Installation
Before You Install
1. Choose a location for the Base near an electrical outlet and a telephone
jack. This phone requires a modular telephone jack and a standard electri-
cal outlet (110V AC) not controlled by a wall switch.
2. Install the Handset battery. Use only VTech batteries.
3. Attach the Belt Clip to the Handset (optional).
NOTE: Install the Base Unit away from electronic equipment, such as personal
computers, television sets or microwave ovens. Avoid excessive heat, cold, dust
or moisture.
a) Remove battery
compartment cover
by pressing on the in-
dentation and sliding
downward.
b) Align the two holes in the plug with the
socketpins,thensnaptheplugintoplace.
c) Place the battery in the compartment
with the wires in the lower right corner.
Angle the top of the battery under the top
clawsfirst, then snap the bottom of the
pack in. Place the wires under the guide,
located below the battery.
d) Replace the battery compartment cover.
To Attatch To Remove
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM4

5
Getting Started
Table/Desk Installation
Installation
4. Charge the Handset Battery
PlacetheHandsetinitsBase.Chargethebatteryatleastfor12hoursbeforeusingyour
telephoneforthefirst time.
5. Check for Dial Tone
Afterthebattery is charged, pickupthe Handset andpress PHONE.Youshouldhear
adialtone.
6. Set the Dial Mode
Ifyou havetouch toneservice, the phone is ready to useas soonas thebatteries are
charged. Ifyou havepulse (rotary)service, you’ll need to change the dialmode.
• PressPROG ontheHandset.
• Press or untilthescreendisplaysDIALMODE:
andthecurrentselection.
• Press SEL.Thecurrentsetting blinks.
• Press toselectTONE orPULSE.
• PressSEL tosave thedisplayedmode.
7. Set Date and Time
IfyousubscribetoCallerIDservice,thedateand time willbesetautomaticallywiththe
firstincoming call.If you donot haveCaller ID service, you canset the date and time
manually:
• PressPROG ontheHandset.
• Press or untilDATE/TIME is displayed. PressSEL.
• Themonthis flashing.Press or untilthescreen displaysthecorrect month.
PressSEL.
• The day is flashing. Press or until the screen displays the correct day.
PressSEL.
• The hour is flashing. Press or until the screen displays the correct hour.
PressSEL.
• Theminuteisflashing. Press or untilthescreendisplaysthecorrect minute.
PressSEL.
•AM or PM is flashing. Press or to choose between AM or PM.
Press SEL.
VTECH TELECOMMUNICATIONS LTD.
DC 6V 300mA
CLASS 2 POWER SOURCE ONLY
CORDLESS TELEPHONE
VTech Cust mer Service 1-800-595-9511
www.vtechph nes.c m
6V DC
Connect the
Power Cord
Standard electrical
outlet
Connect the
Power Cord
Connect the
Telephone
Line Cord
Standard electrical outlet
Modular telephone jack
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM5

6
Getting Started
Wall Installation
1. Runthe power andtelephone linecords through theslots inthe bracket, connecting
themto thejacks located on the undersideof theBase.
2. Connectthe T-shapedbracket tothe slots on the undersideof theBase, as shown
below.
3. MounttheBase Unit ontothewallplate.
4. FollowSteps 4 through 7 in Table/Desk Installation.
a) Alignholeson bracket with
mountingstudsonwallplate.
b) Slidebracketdown onstuds
untilitlocks intoplace.
Installation
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM6

7
Basic Operation
Telephone Operation
End a Call
Press OFF.
OR
Place Handset
in its Base. Exit
programming
Cancel a Page
Channel
Switch to a clear channel
while on a call.
Delete
WhileHandsetis inidlemode,
press and hold to delete all
records in the Call Log.
When viewing the Call Log,
press to delete the current
record displayed.
Handset Volume
Adjust the volume while
on a call. A double beep
will sound when you
reach the maximum or
minimum setting.
Select
UseSELinconjunction
with PROG during
Handsetprogramming.
Forward a Call
While on a call, press
to transfer the call to
the other Handset.
Hold
Press to put a call
on hold. Press again
to release hold.
OR
Lift the Handset of
an extension.
Answer a Call
Press any key
except OFF.
Flash/Call Waiting
Access special
telephone company
subscriber services.
Make a Call
Press PHONE, then dial
the number.
OR
Dial the number (use
to backspace and
correct digits), then
press PHONE to call.
Program
Enter programming
mode with Handset
idle (on hook).
Redial
Press PHONE, then press RE-
DIAL/PAUSE to call the last
number dialed.
OR
Press REDIAL/PAUSE, then
press PHONE to call the last
number dialed.
PressREDIAL/PAUSEtwice to
delete the last number dialed.
Pause
PressREDIAL/PAUSEtoinset
a pause when entering num-
bers.
Handset Operation
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM7

8
Basic Operation
Telephone Operation
Message Waiting Indicator
If you subscribe to telephone
company voice mail with a
visual message waiting signal,
this light flashes, and
MESSAGES WAITING displays
in the Handset screen, when
you have voice mail waiting.
In Use/Charging Indicator
• Flashes slowly when the
Handset is in use.
• Flashes rapidly when a call is
on hold. Glows steadily when
the Handset is charging in its
Base.
Page/Handset Locator
Press to page the Handsets.
Pressagain, pressOFF onHand-
set,orplaceHandsetin the Base
or Charger to cancel the page.
Charging Indicator
Glows steadily when the Handset
is charging in the Charger.
Base and Charger Operation
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM8

9
Basic Operation
Telephone Operation
Handset Ringer Style/Battery Save
You can select from four different Handset ringer styles, or turn the ringer off and
extend the battery life.
1. Make sure the Handset is OFF.
2. Press PROG to enter programming mode.
3. Press until the screen displays RINGER:.
4. Press SEL. The current setting blinks, and you will hear a sample of the ring.
5. Press or to select RINGER:1, 2, 3, 4 or OFF. You will hear a sample of
each ring.
6. Press SEL to choose the displayed ringer setting.
Temporary Tone Dialing
If you have pulse (rotary) service only, you can change from pulse to touch tone
dialing during a call by pressing *TONE. This is useful if you need to send touch
tone signals for access to telephone banking or long distance services.
1. Dial the number.
2. Press *TONE. Buttons pressed after this send touch tone signals.
3. After you hang up, the phone automatically returns to pulse (rotary) service.
Call Forward
An external call can be forwarded from one Handset (HS1) to the other Handset
(HS2).
1. While on a call, press SEL to forward the call to HS2. HS1 will display:
HS2 will ring and show:
NOTE: If HS2 can not be found, HS1 will generate a sad tone and continue
the call automatically. Before HS2 answers, HS1 can press PHONE to cancel
the forward function and continue the external call.
2. Press any key except OFF on HS2 to answer the forwarded call. HS1 will
return to the idle screen.
FORWARDED CALL
SENDING CALL
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM9

10
Basic Operation
Telephone Operation
** RINGING **** RINGING **
** RINGING **** RINGING **
** RINGING **
CONNECTING...CONNECTING...
CONNECTING...CONNECTING...
CONNECTING...
PHONE ONPHONE ON
PHONE ONPHONE ON
PHONE ON
SCANNING...SCANNING...
SCANNING...SCANNING...
SCANNING...
** PAGING **** PAGING **
** PAGING **** PAGING **
** PAGING **
HOLDHOLD
HOLDHOLD
HOLD
BATTERY LOWBATTERY LOW
BATTERY LOWBATTERY LOW
BATTERY LOW
NO CONNECTNO CONNECT
NO CONNECTNO CONNECT
NO CONNECT
Screen Displays: When:
Display Screen Messages
There is a call coming in.
The Handset is waiting for a dial tone.
The Handset is in use.
TheHandset ischangingto anotherof the30
channelsavailable.
The Base is paging the Handset.
There is a call on hold.
TheBatteryneeds to berecharged.
Displays and a sad tone is generated if one
Handset is on a call and the other Handset
pressesPHONE.
Displays and a sad tone sounds when the Base
power is OFF and PHONE is pressed.
NOTE: If HS1 does not respond within 30 seconds, HS1 will start ringing until you
press PHONE to pick up the returned call. If the returned call is not answered
within another 30 seconds, the external call will end automatically.
MESSAGESMESSAGES
MESSAGESMESSAGES
MESSAGES
WAITINGWAITING
WAITINGWAITING
WAITING
You have been alerted by the telephone company
that you have received new voice mail.
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM10

11
Basic Operation
Telephone Memory
You can store up to 9 telephone numbers with names (up to 15 characters and 24 digits in each
location) you dial frequently into the Speed Dial memory locations you assign (1 through 9) in each
Handset. You can also store telephone numbers with names alphabetically in the directory. See
Telephone Directory for instructions.
NOTES:
•The entries you stored in Speed Dial memory will be marked with 01 through 09 in the
telephone directory.
•Press OFF at any time to exit memory dial mode.
Store a Number/Name in Memory:
1. Press PROG on the Handset.
2. Press or until the screen displays SPEED DIAL.
3. Press SEL. The screen displays ENTER 1-9.
NOTE: When memory is full the screen displays MEMORY FULL, an error tone sounds,
and you cannot store a new number until you delete a record in speed dial memory or
telephone directory.
4. Press the key (1 through 9) for the memory location where you’re storing this entry.
If the selected location is empty, the screen displays ENTER NAME.
NOTE: If the location is not empty, your new entry will be stored in place of the old and the
first entry will be deleted. Take caution to not save over entries you do not wish to delete
from memory.
5. Using the chart below, enter up to 15 characters for the name you’re storing with the
number. Use to backspace and make corrections; use to advance and add
a space.
1: 1
2: ABC2
3: DEF3
4: GHI 4
5: JKL5
6: MNO6
7: PQRS7
8: TUV8
9: WX Y Z 9
0: 0
*:
#: &’,-.#
Presses
Dial Key 1 2 3 4 5 6
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM11

12
Basic Operation
8. Press SEL or PROG to store your entry. The screen displays DISTINCT RING?
and the current setting.
9. Press or to change the setting. Choose Y(for yes) if you wish the phone to
alert you to calls from this number by changing to a distinctive ringing pattern after the
first ring. Choose N(for no) for a normal ringing pattern.
10. Press SEL or PROG to confirm your selection. If you chose Y, a D willbe displayed
with the directory entry.
Edit a Number/Name Stored in Memory
1. Press and hold the memory location key (1 through 9) of the entry you wish to edit.
2. When the screen displays the entry you want to edit, press SEL. Then press or
untilERASE flashes.
3. Press SEL.The screen displays the name and number. The cursor appears at the
end of the name. Use , and the dial pad keys to edit the name. Press SEL to
move on to edit the number. Use to backspace and make corrections. Press
SEL to move to edit the Distinctive Ring setting.
4. Press SEL to save the edited information
Delete a Number/Name Stored in Memory
1. Press and hold the memory location key (1 through 9) of the entry you wish to delete.
2. When the screen displays the entry you want to delete, press SEL. Then press or
until ERASE flashes.
3. Press SEL. The screen displays ERASE NO YES and the number.
4. Press or until YES flashes.
5. Press SEL.You will hear a confirmation beep.
Dial a Memory Number
1. Press and hold the memory location key (1 through 9) of the entry you wish to dial.
2. Press PHONE to dial the displayed memory number.
Telephone Memory
6. When you finish entering the name, press SEL or PROG. The screen displays ENTER
NUMBER.
7. Enter the telephone number. Use to backspace and make corrections. Press
REDIAL/PAUSE to store a pause in the dialing sequence.
-OR-
Press REDIAL/PAUSE to display the last number dialed from this phone.
SPEED EDIT ERASE
9735550123 01
SPEEDEDITERASE
9735550123 01
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM12

13
Basic Operation
Reassign Locations in Memory
1. Press and hold the memory location key (1 through 9) of the entry you
wish to reassign.
2. When the screen displays the entry you want to reassign, press SEL.
Then press until SPEED flashes.
3. Press SEL. The screen displays ENTER 1-9.
4. Press the keys (1 through 9) to re-assign this entry into another memory
location. You will hear a confirmation beep.
SPEED EDIT ERASE
9735550123 01
Telephone Memory
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM13

14
Basic Operation
Yourt 2435canstore50(includingthenine Speed Dialentries)telephonenumberswith
names(upto15 charactersforthename and 24digitsforthe numberineachlocation) in
eachHandset.
NOTE:PressOFF atany time toexitdirectory.
Store a Number/Name in the Directory
1. PressPROG.ThescreendisplaysDIRECTORY.
2. PressSEL.ThescreendisplaysENTER NAME.
3. Usingthe chart below,enter upto 15charactersfor thename you’restoring with the
number.Use to backspaceand make corrections; use to advanceand adda
space.
Telephone Directory
4. Whenyoufinishenteringthename,pressSELorPROG.ThescreendisplaysENTER
NUMBER.
5. Enterthe telephonenumber. Use tobackspace andmake corrections.Press
REDIAL/PAUSE tostoreapausein thedialingsequence.
-OR-
Press REDIAL/PAUSE to display the last number dialed from this phone.
6. PressSEL orPROG.The screen displaysDISTINCT RING? and thecurrentsetting.
Presses
Dial Key 1 2 3 4 5 6
1: 1
2: ABC2
3: DEF3
4: GHI 4
5: JKL5
6: MNO6
7: PQRS7
8: TUV8
9: WX Y Z 9
0: 0
*:
#: &’,-.#
Presses
Dial Key 1 2 3 4 5 6
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM14

15
Basic Operation
7. Press or tochangethesetting.ChooseY (foryes)ifyouwishthephonetoalert
youtocallsfrom thisnumberbychanging toadistinctiveringing patternafterthefirst
ring.ChooseN (for no)for anormal ringingpattern.
8. PressSEL or PROG to confirm your selection. If youchoseY, a D willbedisplayed
withthe directoryentry.
NOTE: Whenmemoryisfullthescreen displaysMEMORY FULL , anerrortonesounds,
andyou will notbe ableto store anew numberuntil youdeletea storednumber.
Edit a Number/Name Stored in the Directory
1. Press (DIR).Thescreen displaysDIRECTORY.
2. Press or toscroll alphabeticallythrough the entries stored in thedirectory.
-OR-
Pressthe dial pad key forthe first letterof the entry you wantto edit.
3. Whenthescreen displaystheentryyou wanttoedit,pressSEL. Thenpress or
untilEDITflashes.
4. Press SEL. The screen displays the name and number. The cursor appears at
the end of the name. Use , and the dial pad keys to edit the name. Press
SEL to move on to edit the number. Use to backspace and make correc-
tions. Press SEL to move on to edit the distinctive ring setting.
5. Press SEL to save the edited information.
Delete a Number/Name Stored in the Directory
1. Press (DIR).Thescreen displays DIRECTORY.
2. Press or toscroll alphabetically through entries in the directory.
-OR-
Pressthe dial pad key forthe firstletter of theentry youwant to delete.
3. Whenthescreen displaystheentry youwantto delete,press SEL.Thenpress or
untilERASEflashes.
4. PressSEL.ThescreendisplaysERASENO YESandthenumber.Thecurrent choice
flashes.
5. Press or untilYES flashes.
6. PressSEL.You’llhear a confirmationbeep.
Telephone Directory
SPEED EDIT ERASE
9735550123
SPEED EDIT ERASE
9735550123
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM15

16
Basic Operation
Dial a Number from the Directory
1. Press (DIR).Thescreen displays DIRECTORY.
2. Press or toscroll alphabeticallythrough entriesstored indirectory.
-OR-
Pressthe dial pad key forthe first letter of theentry you wantto dial.
3. Whenthenumberyou want todialisdisplayed,press PHONE.
Telephone Directory
Move a Number/Name to the Memory
1. Press (DIR).ThescreendisplaysDIRECTORY.
2. Press or to scroll alphabetically through directory.
—OR —
Press the dial pad key for the first letter of the entry you want to move.
3. When the screen displays the entry you want to move, press SEL. Then press
until SPEED flashes.
SPEED EDIT ERASE
9735550123
4. Press SEL. The screen displays ENTER 1-9.
5. Press the key (1 through 9) to move this entry from the normal directory to the
Speed Dial memory and assign the memory location. You will hear a confir-
mation beep. A memory location number (01 through 09) will be displayed
with this entry.
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM16

17
Basic Operation
Caller ID Operation
About Call History (Caller ID)
Your t 2435 can store up to 90 calls in its Caller ID memory. The most recent call
will have the highest number. When the memory is full, the oldest call will be
deleted to make room for new incoming call information.
For each call that comes in, the screen displays the following information be-
tween the first and second rings:
• Your caller’s name (15 letters are sent by your telephone company).
• The caller’s area code and telephone number.
• The time and date of the call.
• The repeat Tag (*) in the upper right corner, indicating the party has called
more than once.
If you answer a call before the information appears on the screen, it will not be in
the call history.
NOTE: Each Handset's Call Log is independent from the other Handset. For
example, when you delete one or all Call Log entries in one Handset, they will
not be deleted from the other Handset.
Review Call History
1. Press (CID) to view call history.
2. Use and to scroll through records in call history.
NOTE: Press OFF at any time to exit call history.
Delete Records from Call History
Delete a Specific Call:
1. Locate the record you want to delete from call history.
2. Press DELETE. You’ll hear a long beep confirming the deletion.
DeleteAll Calls:
1. With the Handset in idle (OFF) mode, press and hold DELETE. The screen
Long distance call
Date of call Time of call Position of call
in call history
JOHNSON CHARLIE*
L 908-555-1212
5/01 5:40 28
PM OLD
Party has called
2 or more times
Caller’s
telephone
number
Caller’s name
AM NEW
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM17

18
Basic Operation
Caller ID Operation
Store a Call History Record in the Directory
1. Locate the record in the call history you want to store in the directory.
2. If you wish to change how the number is stored, press #. The screen displays
alternate dialing sequences available for this call (area code + number;
1 + area code + number; number only; 1+ number).
3. Press SEL, then press until PROGRAM flashes.
4. Press SELECT three times. The screen displays:
5. Press or to select Y or Nfor distinctive ringer.
6. Press SEL. You will hear a confirmation beep. If you choose Y in step 5 a D
will be displayed with the directory entry.
DISTINCT RING? N
9735550123
DIAL PROGRAM
973-555-0123
5/015:40PM OLD28
Dial a Displayed Number
1. Locate the record in call history that you want to dial.
2. If you wish to change how the number is dialed, press #. The screen displays
alternate dialing sequences available for this call (area code + number;
1 + area code + number; number only; 1+ number).
3. Press SEL. Press until DIAL flashes.
4. Press SEL again. The number is automatically dialed.
—OR —
When the number is correctly displayed for dialing, press PHONE
DIAL PROGRAM
973-555-0123
5/01 5:40PM OLD 28
displays ERASE ALL NO YES. The current choice flashes.
2. Press until YES flashes.
3. Press SEL. You will hear a confirmation beep.
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM18

19
Basic Operation
Screen Displays: When:
Display Screen Messages
PRIVATEPRIVATE
PRIVATEPRIVATE
PRIVATE The other party is blocking name and/or number
information.
UNKNOWNUNKNOWN
UNKNOWNUNKNOWN
UNKNOWN Your phone company is unable to receive
information about this caller’s name and/or number.
**
**
* (after the name) This caller has called you more than once.
Caller ID Operation
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM19

20
Basic Operation
Batteries
Battery Care and Maintenance
• Your Handset battery should remain charged up to seven days. Average talk
time on a fully charged battery is six hours.
• The Battery needs charging when:
— A new battery is installed in the Handset.
— The phone beeps twice every five seconds.
— The screen displays BATTERY LOW and the low battery icon.
• Place the Handset in its Base so the CHARGING light turns on.The Battery
is typically fully charged in 12 hours.
• You can keep the battery fully charged by returning the Handset to its Base
after each use.
• If you repeatedly get a low battery indicator, even after charging overnight, the
battery should be replaced. Use only VTech batteries.
CAUTION:Toreducetheriskoffireorinjurytopersonsordamagetothe
telephone, read and follow these instructions carefully:
Charge the battery provided with or identified for use with this
product only in accordance with the instructions and limitations
specified in the User’s Manual.
Replacing the Handset Battery
1. Remove the battery compartment cover on the Handset by pressing on the
indentation and sliding the cover downward.
2. Lift out the old battery and disconnect.
3. Align the two holes in the new battery’s plug with the socket pins, and snap
the plug into place. Place the battery in the compartment with the wires in the
ower right corner, along the bottom of the battery.
4. Replace the cover by sliding it up into place.
5. The new battery must be charged before using the phone. Place the Handset
in its Base and allow it to charge for at least 12 hours the first charge. The
telephone might operate before that, but for best performance, let the battery
charge fully.
91-5704-10-00 manual.pmd 4/29/2004, 6:14 PM20