V-tech VC2610 User manual

Specifications are subject to change without notice.
© 2023 VTech Communications, Inc.
All rights reserved. 04/23. VC2610_US_QSG_V1
Need help?
Use your smartphone or mobile device to access our online help.
• Go to https://help.vtechphones.com/VC2610; OR
• Scan the QR code on the right. Launch the camera app or
QR code scanner app on your smartphone or tablet. Hold
the device’s camera up to the QR code and frame it. Tap
the notification to trigger the redirection of the online help.
- If the QR code is not clearly displayed, adjust your
camera’s focus by moving your device closer or
further away until it is clear.
If you would like to contact us, visit
https://help.vtechphones.com/cs.
S
m
You can also call our Customer Support at 1-844-848-
8324 (1-844-84-VTECH) [in US] or 1-888-211-2005 [in
Canada] for help.
For operations and guides to help you using your Baby Unit Floor Stand, and
for latest information and supports, go and check the online help topics and
online FAQs.
VC2610
VC2610
Quick start guide
Baby Unit Floor Stand
(for use with VC2105 5” Smart Nursery
Over-the-Crib Mount Monitor)
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
latest VTech product news.
For more support information:
S
m
VC2610
What’s in the box
• Adult setup is required.
• Children should be supervised to ensure that they do not play with the product.
• The small parts of this device can be swallowed by babies or small children. Keep these
parts out of reach of children.
• The product is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Quick start guide
A
Mounting: second extension Extension cover
C
B
Mounting pole
x3
Connector pipe Connector pipe
AB
Base
x2
Water bag Extension cable
A
B
Cautions
• VC2610 is the floor stand accessary of VC2105. Install VC2610 with VC2105.
• For the best position of viewing, please place the floor stand in the middle of the long
side beside the crib.

Install the oor stand
1. Insert the First extension (A) onto
the Second extension (B), aligning
the slot in between. Make sure the
DC socket is out on opening of the
Second extension and ready for
connection.
2. Let the cable jack of the Extension
cable pass through from the back of
the base.
3. Pick one pole and pass the cable
jack through the pole, then connect
the pole with the Base.
4. Pass the cable jack through the
connector pipe (B) , the second
pole, the second connector pipe
(B), and the third pole in turn.
Align the slot between the poles
and connector pipes (B) and
connect all three poles firmly
with the pipes.
A
B
B
B
Pass the cable jack through the
Second extension (B), to the
opening.
Then connect the Second extension
(B) to the connector pipe (A).
5. Pass the cable jack through the
connector pipe (A), then connect the
pipe with the third pole.
6. Connect the cable jack with the DC socket, then secure the cable with the
Extension cover (C).
A
A
B
D
C
7. Place the floor stand near the crib. Open the base cover, and put the water bag
with water filled into the base to prevent the stand from falling. Then, cover the
base cover.
8. Install the Baby Unit onto the First extension (A). Connect the adapter to the end
of the cable and the power supply to power up the Baby Unit.
Slide the switch to ON to power your Baby Unit on.
Floor stand installation is completed.
Scan QR code to
watch installation
video.
Center of the crib (long side)