V2 PROKSIMA User manual

ZIS173
IL 258
EDIZ. 26/11/2018
PROKSIMA
I
LETTORE DI PROSSIMITÀ
PROKSIMA (CHIAVI READ &
WRITE)
GB
PROKSIMA PROXIMITY
READER (READ & WRITE
KEY)
F
LECTEUR DE PROXIMITÉ
PROKSIMA (CLÉ READ &
WRITE)
E
LECTOR DE PROXIMIDAD
PROKSIMA (PARA LLAVES
READ & WRITE)
P
LEITOR DE PROXIMIDADE
PROKSIMA (PARA CHAVES
READ & WRITE)











H
G
H
T
T
T
T
PROKSIMA-EC PROKSIMA-GC
Fig. 1
Fig. 2 Fig. 3
Fig. 4

- 3 -
12-24 VAC/VDC
GND
DATA
DATA
GND
12-24 VAC/VDC
1
2
3
4
5
6
DECODER
V2
PROKSIMA
1
2
3
4
5
6
PROKSIMA
1
2
3
4
5
6
PROKSIMA
DATA 0
GND
12-24 VAC/VDC
DECODER
WIEGAND
DATA 1
12-24 VAC/VDC GND
Fig. 5
Fig. 6
COLLEGAMENTI
ELETTRICI
ELECTRICAL
CONNECTIONS
BRANCHEMENTS
ÉLECTRIQUES
CONEXIONES
ELÉCTRICAS
CONEXÕES
ELÉCTRICAS
112-24 VAC/VDC 12-24 VAC/VDC 12-24 VAC/VDC 12-24 VAC/VDC 12-24 VAC/VDC
2GND GND GND GND GND
3DATA 0 (Wiegand) DATA 0 (Wiegand) DATA 0 (Wiegand) DATA 0 (Wiegand) DATA 0 (Wiegand)
4DATA 1 (Wiegand) DATA 1 (Wiegand) DATA 1 (Wiegand) DATA 1 (Wiegand) DATA 1 (Wiegand)
5Codice Code Code Código Código
6Ingresso N.C. per il
collegamento di un
sensore
N.C. input for sensor
connection
Entrée N.F. pour la
connexion d’un capteur
Entrada N.C. para la
conexión de un sensor
Entrada N.C. para
a conexão com um
sensor

ENGLISH
- 6 -
PROKSIMA PROXIMITY READER
• PROKSIMA series proximity readers are made from pressure die
cast aluminium.
• 2 LED indicators
• 1 acoustic indicator
• 6-way dip-switches:
- 4 allowing configuration of up to 15 separate devices on the
same line
- 2 for selecting the type of code used by the system
• Available in the PROKSIMA-EC external version and the
PROKSIMA-GC pillar version for GARDO series pillars.
TECHNICAL SPECIFICATIONS
Operating frequency 125 KHz
Maximum consumption 0,7 W
Power supply 12-24 VAC/VDC
Maximum recognition distance 5 cm
Maximum cabled DATA length 100 m
INSTALLATION
PROKSIMA-EC:
1. Decide the layout of the cable trays for running the cables
2. Decide where the system should be installed, bearing in mind
that the base must be fixed on a flat, straight surface.
3. Gently lever off the front panel Ausing a flat-head screwdriver
(Fig 2).
4. Unscrew the 4 screws Mand extract the device Cfrom the
base B(Fig 1).
5. Unscrew the 4 screws Nand remove the rear cover panel D.
6. Drill out the base Bat the point H.
7. Drill out the rear cover Dand insert the cable glands provided
8. Pass the cables through the through hole Hand cable glands
F(Fig. 4).
9. Connect up the device (see the paragraph ELECTRICAL
CONNECTIONS)
10. Fix the base onto the wall using appropriate raw plugs by
means of the 4 through holes T(Fig.4).
11. Insert the device into the base and tighten the 4 screws
12. Insert the front panel
PROKSIMA-GC:
1. Rimuovere il tappo superiore e il vetrino frontale della colonna.
2. Portare i cavi per i collegamenti fino all’estremità superiore della
colonna facendoli passare nelle scanalature dietro le fotocellule.
3. Inserire il vetrino frontale della colonna facendolo scorrere
dall’alto.
4. Rimuovere il frontalino Afacendo leva con un cacciavite a
taglio (Fig 2).
5. Svitare le 4 viti Med estrarre il dispositivo Cdalla base B
(Fig 1).
6. Svitare le 4 viti Ne togliere il coperchio posteriore D.
7. Forare il coperchio posteriore Ded inserire i passacavi in
dotazione
8. Far passare i cavi all’interno del foro He dei passacavi F
(Fig. 4).
9. Collegare il dispositivo (vedi paragrafo COLLEGAMENTI
ELETTRICI)
10. Inserire il dispositivo nella base e fissare le 4 viti
11. Inserire il frontalino
12. Posizionare il dispositivo sopra la colonna, fissarlo utilizzando
le viti Oin dotazione e inserire i due tappini P(Fig. 3).
USING THE DIP-SWITCHES TO CONFIGURE
THE DEVICE
The device is fitted with 6-way dip-switches through which it is
possible to set the proximity reader profile.
Dip switches 5 and 6
Set dip-switches 5 and 6 on the basis of the receiver device to be
interfaced with the proximity reader:
The receiver device to be interfaced
with the proximity reader Dip 5 Dip 6
- V2 decoders
- V2 control units with data input
OFF ON
- Devices with 26 bit Wiegand data input ON OFF
Dip switches 1 - 2 - 3 - 4
If the system has the option to use one or more proximity readers
with the same function, it is necessary to connect the devices in
parallel and set the same combination for Dip 1,2,3,4 on all of
them.
NOTES: if the readers need to control different channels
with the same key or token, simply connect the devices in
parallel and set different DIP 1,2,3,4 combinations.
The following table lists the 15 possible combinations:
PROKSIMA VRD
Dip
1
Dip
2
Dip
3
Dip
4
Winppcl
(TASTO)
Jumper
J1
Jumper
J2
1ON OFF OFF OFF 1 OPEN OPEN
2OFF ON OFF OFF 2 CLOSED OPEN
3OFF OFF ON OFF 3 OPEN CLOSED
4OFF OFF OFF ON 4 CLOSED CLOSED
5OFF OFF ON ON 3+4
6OFF ON OFF ON 2+4
7OFF ON ON OFF 2+3
8OFF ON ON ON 2+3+4
9ON OFF OFF ON 1+4
10 ON OFF ON OFF 1+3
11 ON OFF ON ON 1+3+4
12 ON ON OFF OFF 1+2
13 ON ON OFF ON 1+2+4
14 ON ON ON OFF 1+2+3
15 ON ON ON ON -
mPLEASE NOTE: The configurations highlighted in the
table are consistent, in the case of mixed installations
(PROKSIMA - VRD) with configuring devices so that they are
not in conflict.
In the case of replacing a VRD reader with a PROKSIMA
reader, configure the new device with the configuration
corresponding to the old one.

ENGLISH
- 7 -
MEMORISING ACCESS DEVICES
Memorising various access devices (VTR or VCR) in your system
can be done in two different ways:
Direct programming
1. Activate memorising on the receiving device by following the
procedure indicated in the instruction manual.
2. Bring the access device (VTR or VCR) close to the front panel
of the proximity reader (a distance of 5 cm). The temporary
extinguishing of LED L1, accompanied by a BEEP, indicates the
VTR has been recognised.
3. Check memorising on the receiver has occurred.
Programming using WINPPCL, PROGTAG and PROG2
WINPPCL: allows the creation of codes with which to serialise VTR
and VCR access devices
PROGTAG: allows the serialising of access devices with the codes
generated by WINPPCL
PROG2: allows downloading of the codes created in the V2
receiver devices
EU DECLARATION OF CONFORMITY
V2 S.p.A. hereby declare that PROKSIMA equipment conforms to
the essential requirements established in directives:
• Low Voltage Directive 2014/35/EU
• Electromagnetic Compatibility Directive 2014/30/EU
• Radio Directive 2014/53/EU
• Directive ROHS2 2011/65/CE
Racconigi, 01/06/2015
Legal representative, V2 S.p.A.
Antonio Livio Costamagna
ELECTRICAL CONNECTIONS
mWARNING: Ensure that the device is set in its metallic
case before supplying power in order to check the correct
working.
To connect one or more PROKSIMA devices to a V2 decoder,
follow the wiring diagram shown in Fig. 5
To connect a PROKSIMA device to a V2 control unit with
data input, follow the procedure indicated in the control unit
instruction manual.
To connect a proximity reader to a 26 bit Wiegand receiver device,
follow the wiring diagram shown in Fig. 6
Input 6 (N.C.) may be used for connection to a sensor for
indicating the status of the entrance (OPEN/CLOSED).
When the input is open, LED L2 is on.
If the input is not used, and it is desired to keep LED L2 off,
jumper terminal 6 (N.C.) with terminal 2 (GND).
SIGNALS
The device signals changes in status by means of the LEDs L1, L2
and a buzzer (acoustic indicator).
L2 L1
LED L1: this is on when the device is powered it is off when the
device is transmitting the code
LED L2: is off when terminal 6 is closed to ground (GND).
It can be used for connecting a sensor to indicate the status of an
entrance (OPEN/CLOSED).
Buzzer: emits a beep each time an access device (VTR or VCR)
is brought close to the proximity reader.

V2 S.p.A.
Corso Principi di Piemonte 65/67
12035 RACCONIGI CN (ITALY)
Tel. [phone] - Fax [phone]
[email protected]
www.v2home.com