Valon 5009 User manual

Valon Technology
5009 Quick Start Guide
5009 Quick Start Guide
Step 1: Power Supply Connection
You are
going to need a 6Vdc ±0.5V at
connect to your power supply.
Connect it and you should see two blue LEDs illuminating through the
label just below the Source 1 and Source 2 label markings. Your 5009 will now be set to 2440MHz on
Source 1 and 2480MHz on Source 2.
See “Hints and Kinks –
Power Supplies”
Step 2: USB connection
Connect the provided USB cable to your 5009 and host computer. Your computer
a new FTDI Virtual Com Port. If you have trouble, then it is likely you do not have the correct VCP
(virtual com port) d
river. (Download FTDI CDM v2.12.00 WHQL Certified.zip from the link below, unzip
and run).
Step 3: Terminal Program
You will need a terminal program to change your 5009 settings. Just about any terminal program will
work. We have provided
5000term
correct Virtual Com Port. If you use a different terminal program, your port settings are 9600, 8, None,
1, None.
Step 4: Synthesizer Settings
After launching your terminal program, press th
cursor like this: “-1-
>”, if you do, you have successfully established communications with your 5009.
Type help to get the help menu
control-c will exit program.
control-f will increase the baud r
ate to 115200.
control-
r will reset the synthesizer to factor default settings..
Consult the
Valon 5009 Operations Manual
Note that as of this date, not all commands in the Operations Manual are available
become available, we will notify you and you will be able to download the update
also use the 5000term
.exe terminal program to load the *latest*.bin files.
For the latest 5009 Downloads:
http://www.valontechnology.com/5009users/5009.htm
Above all, if you have trouble or need help just
Stuart Rumley
650-369-0575
[e-mail]
5009 Quick Start Guide
1
Step 1: Power Supply Connection
going to need a 6Vdc ±0.5V at
600mA power supply. Use the supplied red-
black Hirose cable to
Connect it and you should see two blue LEDs illuminating through the
label just below the Source 1 and Source 2 label markings. Your 5009 will now be set to 2440MHz on
Source 1 and 2480MHz on Source 2.
Power Supplies”
on back of this document.
Connect the provided USB cable to your 5009 and host computer. Your computer
should recognize it as
a new FTDI Virtual Com Port. If you have trouble, then it is likely you do not have the correct VCP
river. (Download FTDI CDM v2.12.00 WHQL Certified.zip from the link below, unzip
You will need a terminal program to change your 5009 settings. Just about any terminal program will
5000term
.zip . Unzip and running 5000term
.exe will automatically find the
correct Virtual Com Port. If you use a different terminal program, your port settings are 9600, 8, None,
After launching your terminal program, press the Enter key a few times and check to see that you get a
>”, if you do, you have successfully established communications with your 5009.
ate to 115200.
r will reset the synthesizer to factor default settings..
Valon 5009 Operations Manual
for more information on the use of these commands.
Note that as of this date, not all commands in the Operations Manual are available
.
As these commands
become available, we will notify you and you will be able to download the update
d
*.bin files. You
.exe terminal program to load the *latest*.bin files.
http://www.valontechnology.com/5009users/5009.htm
Above all, if you have trouble or need help just
contact us.
06/27/2018
black Hirose cable to
Connect it and you should see two blue LEDs illuminating through the
label just below the Source 1 and Source 2 label markings. Your 5009 will now be set to 2440MHz on
should recognize it as
a new FTDI Virtual Com Port. If you have trouble, then it is likely you do not have the correct VCP
river. (Download FTDI CDM v2.12.00 WHQL Certified.zip from the link below, unzip
You will need a terminal program to change your 5009 settings. Just about any terminal program will
.exe will automatically find the
correct Virtual Com Port. If you use a different terminal program, your port settings are 9600, 8, None,
e Enter key a few times and check to see that you get a
>”, if you do, you have successfully established communications with your 5009.
for more information on the use of these commands.
As these commands
*.bin files. You
can
http://www.valontechnology.com/5009users/5009.htm

Valon Technology
5009 Quick Start Guide
5009 Hints and Kinks –
Power Supplies
Occasionally, we get a trouble call from a new 5
frequency after power up. Usually it’s just one of the RF Sources that won’t lock. After doing to some
investigation the problem almost always is caused by the power supply. The power supply is usually
standard lab bench supply.
The power supply is not the problem nor is there anything wrong with the 5009. The problem is how
the power supply is set up and used. Follow these suggestions to make sure you don’t run into start up
problems:
1. Current limit set
too low. Make sure the current limit is set well above the required 560mA.
Best to set the current limit to 1.0A.
2.
Preset the output voltage to 6.0+V. Don’t set the power to exactly 6.0V. It’s best to set the
power supply a little higher in order to co
3.
Use the power supply on/off switch to power on the 5009. Biggest problem with erratic 5009
performance with lab supplies is the user “dialing up” the voltage slowly from 0V. This will
sometimes confuse
the power
just adjust the output voltage first and then power
cable into the powered on power supply.
5009 Quick Start Guide
2
Power Supplies
Occasionally, we get a trouble call from a new 5009 user who says that the 5009 will not lock on
frequency after power up. Usually it’s just one of the RF Sources that won’t lock. After doing to some
investigation the problem almost always is caused by the power supply. The power supply is usually
The power supply is not the problem nor is there anything wrong with the 5009. The problem is how
the power supply is set up and used. Follow these suggestions to make sure you don’t run into start up
too low. Make sure the current limit is set well above the required 560mA.
Best to set the current limit to 1.0A.
Preset the output voltage to 6.0+V. Don’t set the power to exactly 6.0V. It’s best to set the
power supply a little higher in order to compensate for I*R drop of the power supply cables.
Use the power supply on/off switch to power on the 5009. Biggest problem with erratic 5009
performance with lab supplies is the user “dialing up” the voltage slowly from 0V. This will
the power
-on-
reset circuitry resulting in an unlocked synthesizer
just adjust the output voltage first and then power
-
cycle the power supply or plug the power
cable into the powered on power supply.
06/27/2018
009 user who says that the 5009 will not lock on
frequency after power up. Usually it’s just one of the RF Sources that won’t lock. After doing to some
investigation the problem almost always is caused by the power supply. The power supply is usually
The power supply is not the problem nor is there anything wrong with the 5009. The problem is how
the power supply is set up and used. Follow these suggestions to make sure you don’t run into start up
too low. Make sure the current limit is set well above the required 560mA.
Preset the output voltage to 6.0+V. Don’t set the power to exactly 6.0V. It’s best to set the
mpensate for I*R drop of the power supply cables.
Use the power supply on/off switch to power on the 5009. Biggest problem with erratic 5009
performance with lab supplies is the user “dialing up” the voltage slowly from 0V. This will
reset circuitry resulting in an unlocked synthesizer
. Best to
cycle the power supply or plug the power