Van Heck Badkamers Long Island Series User manual

Opmerkingen:
Amachtstraat 8a • 7622 AP Borne • Tel.: 074 - 266 20 35 • Fax.: 074 - 266 90 56 •
K.v.K. Enschede 06075299 • Bank: ABN-AMRO 42.71.91.297 • BTW: NL803645600B01
Artikelnr.: 72&
Serie: /RQJ,VODQG
Type:%DGGRXFKHPHQJNUDDQVWDDQG
[e-mail] • www.vanheckbadkamers.nl
De informatie op deze pagina was correct op de datum van opmaak.
Van Heck badkamers is niet verantwoordelijk voor de veranderingen die optreden door verbeteringen aan onze producten
Geen
Geen
Geen
Geen
De informatie op deze pagina was correct op de datum van opmaak

important - please read
general installation
Please read these instructions carefully before starting installation and keep for future
reference.
Remove all packaging and check the product for missing parts or damage before
starting installation.
Any alterations made to this product and ttings may infringe water regulations and
will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority
Regulations/Byelaws and Building and Plumbing (UK:BS6700) Regulations.
We strongly recommend that you use a qualied and registered plumber.
These ttings are mixing devices and therefore water supplies must be reasonably
balanced.
Where connections are made to the mains cold water supply, WRC approved single
check valves must be tted to both hot and cold inlets. This is a stated requirement of
Water Supply (Water Fittings) Regulations 1999 Schedule 2, Section 6 G15.13.2
Before making any inlet pipe connections, all supply pipes MUST be thoroughly
ushed to remove debris. Failure to do so could result in damage or low ow from the
mixer unit. Water Supply (Water Fittings) Regulations 1999 Schedule 2 Section 4 G13.1
The tting of isolating valves to the inlet feeds is advised for ease of maintenance.
Please take great care when installing this mixer not to damage its surface.
care of the mixer
Our products are nished to the highest standard and due care needs to be taken to
ensure their looks are retained.
We recommend cleaning all products with a soft damp cloth ONLY and advise strongly
against the use of ALL cleaning products i.e. powders and liquids.
If the above instructions are not followed this will invalidate your guarantee in the
event of a problem occurring.
installers/users notes
Nua 133.indd 2 23/7/08 10:30:22

dimensions
operation
installation - showerhead
Pull the shower control knob
in to turn on the shower, pull
out to close.
Rotate the handle to
increase/decrease
the temperature.
Pull the handle to
increase/decrease
the ow of water.
Shower holder
Operating Specications
Hot Water Supply Temperature:
Maximum: 85° C
Minimum: 10° C higher than the maximum required mixed temperature (advise 65° C)
Minimum operating pressure 3 bar
Maximum operating pressure 5 bar
251mm
997mm
1095mm
850mm
80mm
Min 115mm
191mm
½"
79mm
93mm
755mm
54mm
90mm
74mm
Showerhead
Place one of the rubber washers into the
cone end of the hose and screw to the
Showerhead.
Place the second rubber washer into the
other end of the hose and attach it to
the mixer outlet.
Nua 133.indd 3 23/7/08 10:30:26

installation installation
Before installing your new mixer, ush
through the pipework to ensure removal
of debris, turn o the water supply.
Warning! Please check for any
hidden cables and pipes before drilling
holes.
Position the seat and mark the 3 xing
holes, remove the seat and drill the 3 x
12mm holes to the required depth.
Insert the expansion bolts into the holes.
Slide the seat over the studs followed
by the 3 washers and nuts. Use the
adjusting screws to level the seat, when
satised with the level nally tighten
down the bolts.
Connect the inlet pipes to the seat with
the hot on the left and cold on the right.
Nut
Washer
Seat
Bolts
Adjusting
screw
Bolts
Hot inlet
Cold inlet
Seat
Front
Finish the oor covering down to a
diameter of 75 to 89 mm.
Remove the 2 screws and pull out
the safety cover.
Insert the main body assembly into
the seat, tighten the fastening plate,
and cover with the escutcheon.
Seat
75-89mm
Safety
cover
Screws
Seat
Escutcheon
Fastening
plate
Floor
Nua 133.indd 4 23/7/08 10:30:30