Varytec VF - 120 User manual

User’s manual
Foam Machine VF - 120

2 / 9
Table of content
1. Safety instructions........................................................................................................................... 3

3 / 9
1. Safety instructions
OR SAFE AND EFFICIENT OPERATION
e careful with heat and extreme temperatureAvoid exposing it
direct rays of the sun or near a heating appliance.
ot put it in a temperature bellow 41°F /5°C, or exceeding 95°F /35°C.
eep away from humidity, water and dust
o not place the set in a location with high humidity or lots of dust.
ontainers with water should not be placed on the set.
eep away from sources of hum and noise
uch as transformer motor, tuner, TV set and amplifier.
o avoid placing on un-stable location
elect a level and stable location to avoid vibration.
o not use chemicals or volatile liquids for cleaning
se a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
sales agency immediately
, and contact with an engineer for repairing,
o not open the cabinet by yourself, it might result a
anger of electric shock.
ake care with the power cable
ever pull the power cable to remove the plug from the receptacle, be sure
hold the plug. When not using the player for an extended period of time
e sure to disconnect the plug from the receptacle.
F
B
to
N
K
D
C
K
S
T
S
D
U
If out of work, contact
Any troubles arose, remove the power plug soon
d
d
T
N
to
b

4 / 9
2. Introduction
Thank you for choosing an Varytec Special Effects Machine. You now own a rugged and
e suggest that you carefully read all of the
structions. By following the suggestions found in this user manual, you can look forward
ine for years to
Please follow these operation, safety and maintenance instructions to ensure a long
am machines.
ck
1. Keep this device dry.
se.
outlet only. Prior to use take
care to determine that the unit is installed at the rated voltage.
or Foam Machine before filling its tank.
6. Turn off or unplug when not in use.
ture, water, or snow/foam liquid gets
ce technician or
8. There are no user serviceable parts inside. Refer to your dealer or other
nozzle directly at people.
11. Locate the machine in a well-ventilated area. Never cover the unit’s vents. In order to
ion, allow a free air space of at least 20 cm around the
, perfume) to the snow liquid.
Pay attention to all warning labels and instructions printed on the exterior of your
Varytec Foam Machine.
1. Use only the high-quality foam liquid that your dealer recommends.
2. Always make sure there is sufficient liquid in the machine’s liquid tank.
3. If your Varytec machine fails to work properly, discontinue use immediately. Drain all
liquid from the tank, pack the unit securely (preferably in the original packing material),
and return it to your Varytec dealer for service.
powerful state-of-the-art machine. Prior to use, w
in
to the reliable and satisfactory performance of your Varytec Foam Mach
come.
and safe life for fo
3. CAUTION Danger of electric sho
2. For inside use only. Not designed for outside u
3. For the 110V models, use 3-prong grounded electrical
4. Always unplug your ANTARI Snow
5. Keep foam machine upright.
7. This machine is not water- or splash-proof. If mois
inside the housing, immediately unplug the unit and contact a servi
your dealer before using it again.
qualified service personnel.
9. For adult use only. These machines must be installed out of the reach of children.
Never leave the unit running unattended.
10. Never aim the output
guarantee adequate ventilat
sides and top of the unit.
Danger of explosion
1. Never add flammable liquids of any kind (oil, gas

5 / 9
4. Unpacking and Inspection
ent damage caused by transportation. In the event that the unit’s housing or cable
damaged, do not plug it in and do not attempt to use it until after contacting your
deale
5. Setup packing materials from shipping box. Check that all foam and plastic
padding is removed, especially
a flat surface and remove the liquid tank cap.
mended high-quality water-based
level or suspended overhead. Install the
guarant
and top the public area. Please consider that liquid may
acciden ay from persons. The minium distance should be
eed 15°.
This device is constructed for a standing device is to be installed
The installation of the device has to be built and constructed in a way that it can hold 10
times the w
This de
overhea
Open the shipping carton and verify that all equipment necessary to operate the system
has arrived intact. Accompanying the S-120 foam machine should be a hanging bracket
and fluid tank. If any equipment is missing contact your dealer immediately.
Before beginning your initial setup on the Foam Machine, make sure that there is
no evid
is
r for assistance.
1. Remove all
in the nozzle area.
2. Place the machine on
3. Fill with Varytec Foam Liquid or other dealer-recom
snow or foam fluid. Any other types of fluid can damage the unit. When filled, place
cap back on liquid tank.
6. Installation
The Foam Machine may be installed at floor
Foam machine in a well-ventilated area. Never cover the unit’s vents. In order to
ee adequate ventilation, allow a free air space of at least 20 cm around the sides
of the unit. Install the device out of
be spilt during operation around the device. The resulting slippery surface can cause
ts. Position output of foam aw
1.5 m. Only install the machine on scratch resistant and water resistant surfaces.
Please make sure that the inclination angle does not exc
installation only. If the
overhead, the following safety instructions are binding:
eight for 1 hour without any harming deformation.
vice is constructed for a standing installation only. If the device is to be installed
d, the following safety instructions are binding:

6 / 9
The installation of the device has to be built and constructed in a way that it can hold 10
installation
den.
s
ation another time.
as to make sure that safety-relating and machine-technical installations are
tallations are
Proced
The device should be installed outside areas where persons may walk by or be seated.
ing
erty.
ional trussing systems
have to be used. The device must never be fixed swinging freely in the room.
Caution: Devices in hanging installations may cause severe injuries when crashing down!
If you have doubts concerning the safety of a possible installation, do NOT install the
Mount the device to your trussing system using an appropriate clamp.
times the weight for 1 hour without any harming deformation.
When rigging, derigging or servicing the device staying in the area below the
place, on bridges, under high working places and other endangered areas is forbid
The operator has to make sure that safety-relating and machine-technical installations are
approved by an expert before taking into operation for the first time and after change
before taking into oper
The operator h
approved by an expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical ins
approved by a skilled person once a year.
ure:
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, includ
(but not limited to) calculating working load limits, installation material being used, and
periodic safety inspection of all installation material and the device. If you lack these
qualifications, do not attempt the installation yourself, but instead use a professional
structural rigger. Improper installation can result in bodily injury and or damage to prop
The device has to be installed out of the reach of people.
If the device shall be lowered from the ceiling or high joists, profess
device!
Before rigging make sure that the installation area can hold a minimum point load of 10
times the device's weight.

7 / 9
For overhead use, always install a safety-rope that can hold at least 12 times the weight of
screw cap. Pull the safetyrope
rough the hole in the mounting-bracket and over the trussing system or a safe
e fixation
. Operation
power cord into a grounded electrical outlet. Turn the power switch on rear of unit
2. The machine will begin producing foam as soon as it is turned on. To stop the foam,
unit.
you experience low output, mechanical noise or no output at all, unplug immediately.
d power from the wall. If all of
e above appears to be O.K., plug the unit in again. If you are unable to determine the
id
r and the snow machine liquid tank immediately after filling.
efore storing, flush out system with clean water.
ill with Varytec Foam Liquid or other dealer-recommended high-quality water-based
Save these instructions.
the fixture. You must only use safety-ropes with quick link with
th
fixation spot. Insert the end in the quick link and tighten the safety screw.
The maximum drop distance must never exceed 20 cm.
A safety rope which already has held the strain of a crash or which is defective may not be
used again. Adjust the desired inclination-angle via the mounting-bracket and tighten th
screws.
71. Plug
to the "ON" position.
turn the power switch to the “OFF” position.
Important: Always monitor tank fluid level during operation.
Running a foam machine without fluid can permanently damage the
If
Check fluid level, the external fuse, remote connection, an
th
cause of the problem, do not simply continue pushing the remote button, as this may
damage the unit. Return the machine to your dealer.
8. Maintenance
Do not allow foam liquid to become contaminated. Always replace the caps on the liqu
containe
B
Foam Liquid
F
snow or foam fluid. Any other types of fluid can damage the unit.

8 / 9

9 / 9
Importeur:
B & K Braun GmbH
Industriestraße 1
D-76307 Karlsbad
www.bkbraun.com
[email protected]