Vauni Edge User manual

Manual

Vauni Edge/Shadow

Important!

Read through the en!re manual and give special a"en!on to the safety instruc!ons before using the

product.

ENG/SVE

Version SE42-1411

Innehåll

1 Introduc•on..........................................................................................................................................1

2 Descrip•on of the •replace..................................................................................................................2

3 Installa•on............................................................................................................................................3

3.1 Assembly and installa•on ...........................................................................................................3

4 Firing.....................................................................................................................................................6

4.1 Ligh•ng the •replace ..................................................................................................................6

4.2 Fuel .............................................................................................................................................6

4.2.1 Recommended fuel quality.......................................................................................................7

4.2.2 Re•lling with fuel .....................................................................................................................7

4.2.3 Handling of spillage .................................................................................................................8

4.3 Ex•nguishing the •replace..........................................................................................................8

4.4 To keep in mind during the •replace’s opera•on........................................................................8

5 Safety instruc•ons................................................................................................................................9

5.1 General........................................................................................................................................9

5.2 Installa•on and use.....................................................................................................................9

5.3 Service and maintenance..........................................................................................................10

6 Maintenance and care........................................................................................................................11

6.1 General cleaning .......................................................................................................................11

6.2 The burner system ....................................................................................................................11

7 Fault •nding........................................................................................................................................12

8 Technical speci•ca•ons ......................................................................................................................15

1 Introduction

Thank you for choosing an ethanol-powered !replace from Vauni. As a customer you can be

certain that you have selected a product with market-leading quality, user-friendliness and design.

If the !replace is used and maintained in accordance with this manual, you will have many years’

enjoyment of your product.

Before the !replace is put into use, it is important that you carefully read through this manual, since

it contains important safety informa"on. Vauni recommends that all the persons who spend "me

near the !replace are informed about, or read, the safety instruc"ons.

This product is cer"!ed according to the highest European standards, which guarantee secure and

safe ownership.

Have great pleasure with your new !replace#

Cer••ca•on informa•on

Cer"!cate of approval / Cer"!ca"on number:

0236/07

Note!

Vauni AB reserves the right to make minor revisions without prior informa"on. Parts of the product are results

of handicra$, which means that small varia"ons in colour and material structure are normal.

This manual contains instruc"ons for correct u"liza"on of the product. Improper use voids guarantee.•

2 Description of the •ireplace

The !replace has the following parts and standard accessories:

1x Stove frame

1x Burner module including regulator lid and regulator rod

The regulator lid is moved with the regulator rod over the burner module for stepless regula"on of

the #ame size as well as for fast and safe ex"nc"on of the !replace.

1x Wall mount including screw set

1x Manual

1x Funnel

1x Metal front (Edge)

1x Glass front (Shadow

Note! When li$ing the !replace: place hands here (2 persons recommended)

A Stove frame

B Wall mount/!xture

C Front (Edge)

D Glass door (Shadow)

E Backside of glass door

F Magnet/Child safety lock

GHinges

HBurner module

(with opening and matrix)

I Regulator lid

J Regulator rod

3 Installation

The !replace is designed to allow "exible placement in most interiors, and requires a minimum of

assembly and installa#on before it can be used. To ensure that the !replace’s full safety is u#lized, it is

important that the instruc#ons below for assembly be followed when the !replace is installed.

Keep in mind!

The !replace is cer#!ed to be placed in a space with a minimum volume of 32 m3(an equivalent

"oor area is 13 m2) and with normal ven#la#on (0.5 exchange of air per hour). It is important that

the placement is chosen so that the "ame is not exposed to direct draught, and places should be

especially avoided where the draught’s direc#on is against the !replace’s opening. In"ammable

objects must not be placed within 1 metre from the !replace. Remember that curtains and similar

objects must have a safety margin of at least 1 metre due to risk of draught currents. (Figure 18)

3.1•Assembly•and•installation

The Edge/Shadow is to a large extent assembled already when delivered, and needs only minor

post-assembly and installa#on. Follow the steps below to assemble and install the product. Vauni

recommends that the assembly is done by two persons, since some steps require heavy li$ing.

Note! Depending on the market and model variants, minor devia#ons may occur.

Prepara•ons:

1. Remove the !replace and its accessories from the packaging and check the details for possible

transport damage. Any damage must be reported immediately to the deliverer and to the place

of purchase.

2. Check that all the parts and standard accessories speci!ed in Sec#on 2 are included.

3. Check that you have the right tools; see Sec•on 8, Technical speciﬁca•ons. (Figure 22)

For Edge - Moun•ng the front (point 4-6):

4. Place the front (face down) on the "oor well protected with a so$ surface, i e the packaging

material.

NOTE: For Edge Stainless: Remove the protec"ve plas"c from the front a#er the $replace is

mounted on the wall

5. Place the stove frame over the front. Posi#on the six screw holes as shown in Figure 1.

465

X 6

X 4

6. Mount screws according to Figure 2. Make sure the screws go in straight and without much

resistance. Use an Allen wrench - •ghten so that it is securely mounted.

The front is now mounted - the •replace is ready for installa•on on the wall. Go to point 12.

For Edge - Moun•ng the glass front (point 7-11):

7. Place the glass front (glass down) on the !oor well protected with a so" surface, i e the packaging

material.

8. Place the stove frame over the front. Posi•on the screw holes of the stove frame over the

threads of the glass front hinges as shown in Figure 4.

9. Make sure that the glass front sits straight over the stove frame.

10. Secure the glass door by following the principle in Figure 5. First, place the washer over the

thread, then •ghten the nut with a wrench.

11. Make sure the glass front is secured and that the door can be opened and closed freely.

(Figure 6)

Moun•ng on a wall (point 12-21):

Note! Vauni recommends that wall moun•ng be done by a quali•ed professional.

12. Find a suitable brick wall, concrete wall, massive wooden wall or a stud wall with a strong

construc•on panel. Make sure the •replace will be at least 1 metre from !ammable objects and

not be exposed to draughts. (Figure 18) If the wall is built on joists and simpler •nishing plate,

e.g. plaster boards, the wall •xture must be a#ached to exis•ng reinforcements (e.g. wall beams)

and/or arranged reinforcements. The •replace weighs 30 kg and the a#echment of its weakest

point is to bear this weight. Contact a quali•ed professional if in the least doubt.

13. Li" the •replace with the help of two people, and place it against the intended wall for

installa•on. Adjust it to an adequate height for moun•ng, and then mark at the •replace’s bo#om

edge with a pencil or the like. Vauni recommends in general a distance of 80-90 cm from the !oor

to the Edge/Shadow’s bo#om edge. (Figure 7)

14. Place the base of the wall mount at the marked line and control that it sits horizontal using a

spirit level. Next, mark out the hole picture for the accompanying fastening screws with a pen,

using the wall •xture as a template. Vauni recommends 6-8 screw points. Then drill holes of a

suitable size at the markings. (Figure 8)

11 12

X 4

15. Insert the accompanying screw plugs in the drilled holes, then screw on the wall •xture with the

accompanying screws. Check very carefully that the wall •xture sits steady and gap-free against

the wall. (Figure 9) Contact a quali•ed professional at the least suspicion of insu•cient bearing

capacity.

16. Li• the •replace with the help of two people and hook it to the wall •xture. When the hooks are

correctly placed, both the upper and lower hooks should lock into the •replace. (Figure 10-11)

Check on both sides that both of the upper and lower hooks are correctly placed. (Figures 11)

Important! If the hooks are not in the correct posi•on, there is a higher risk that the •replace

will fall due to external force, so check this very carefully.

17. Tighten the two cap screws on the underside of the •replace (Figure 12). Make sure the stove is

level and stable.

18. For Shadow: Make sure that the door can be opened and closed freely. (Figure 13)

VARNING! Shadow’s glasdoor shall always be handled carefully! The glass door must not be

loaded heavily! Never hang in the door - either in open or closed posi•on! Injury can occur!

19. For Shadow: The glass door is equipped with magne!c and mechanical child safety lock, which

sits hidden behind the glass door’s right side. The lock is opened and closed by moving the bar as

shown in Figure 14.

20. Lower the burner in the provided holder into the •replace. (Figure 15)

21. Place the regulator lid by lowering the two guide pins into the respec!ve grooves (Figure 16).

When correctly placed, the regulator lid should lie closely against the burner’s surface and slide

easily when the regulator rod (which grips in the holes provided in the regulator lid) moves it

to its respec!ve stop. In the open posi!on, the regulator lid should be in front of the burner’s

opening as seen from in front of the •replace. (Figure 16)

Now that the •replace is completely assembled, read Sec!on 4 Firing for instruc!ons on how to start

it the •rst !me.

17 18

min 1 meter

1 metre

1513

4 Firing

Be careful to read through this sec!on and make sure that all users of the "replace understand the

safety prescrip!ons before it is put into use.

4.1•Lighting•the••ireplace

At the "rst start, points 1-6 are followed. For later normal use, points 2-6 are followed. When

reposi!oning, or making other changes in the "replace’s surroundings, points 1-6 are to be followed.

Note! Do not add fuel if you do not intend to start the "replace immediately; see Sec!on 4.2.2

Re•lling with fuel below.

1. See that the assembly and installa!on are done according to the instruc!ons in Sec!on 3.

2. Check that the regulator lid lies closely against the burner’s surface and slides easily when the

regulator rod moves it to its respec!ve stop. When the lid is in the closed posi!on, it should cover

the en!re burner opening.

3. Open the regulator lid completely with the regulator rod. Add fuel according to the instruc!on

4.2.2 Re•lling with fuel below. If the "replace is recently used, allow it to cool down for at least 15

minutes.

Warning! Fuel must never be added in a burning "replace#

4. Check that there is no spilled fuel on or outside the "replace. Light the "replace by holding a

lighter with extended !p next to the burner matrix. See that no in$ammable material is present

within a distance of 1 metre. The "replace will start immediately, and in a short !me it will

produce beau!ful dynamic yellow $ames. If necessary, the $ames’ e%ect is regulated steplessly

with the regulator rod.

Note! At cold start, if fuel has been le& long in the "replace, a safety func!on prevents it from

ligh!ng immediately. In such a case the "replace can be started by holding the lighter lit for about

10 seconds while its $ame barely touches the burner matrix. If the "replace does not start, add

new fuel according to Sec!on 4.2.2, keeping in mind that the burner in this case will absorb less

than 2 litres.

Warning! This procedure may increase the wear on the burner and thus reduce its life!me. Vauni

recommends that tanking be done not long before the "replace is used.

5. If the "replace goes out immediately a&er ligh!ng – repeat the ligh!ng procedure in point 4

above.

6. If possible, run the "replace un!l it goes out or the $ames are very small.

Note 1! On the "rst occasions of "ring, some smell may arise – this is quite normal. The smell

decreases gradually a&er a number of "rings.

Note 2! A clicking sound may occur during "ring, at the start or when the fuel level is low and the

$ames are smaller. This is quite normal.

4.2•Fuel

The Edge/Shadow is op!mized for, and must only be used with, liquid denatured ethanol – whose

burning produces only carbon dioxide and water vapour, the same components as in the air we

breathe out.

Warning! The fuel must not be preheated.

4.2.1•Recommended•fuel•quality

For Vauni Edge/Shadow we recommend Vauni ECO-FLAME which is the market’s most op!mal bio-

ethanol fuel for use in chimney-free "replaces and inserts. This product gives natural, smoke- and

soot-free #ames with a neutral aroma, and can be ordered at www.vauni.com. In cases where ECO-

FLAME is not available, only liquid denatured ethanol (bio-ethanol) must be used, which is sold under

various trade names at building-supply stores, DIY-stores, petrol sta!ons and large markets. (Applies

for Sweden – for other markets consult your distributor)

Denatured ethanol is an in#ammable liquid, and therefore must be handled with great care – in

Sweden according to the prescrip!ons and general advice for handling in#ammable liquids (Na!onal

Inspectorate of Explosives and Flammables, SÄIFS 2000:2). Handling of larger amounts than 100 litres

requires a permit for handling of in#ammable goods (SÄIFS 1995:3). For more informa!on, see www.

raddningsverket.se (Applies for Sweden – for other markets consult your distributor)

Before adding fuel: it is very important that the correct quality of fuel is used – so check again to be

sure. Bio-alcohol in gela•nous form, or ethanol fuel for automobiles such as E85, must not be used

under any circumstances! If non-recommended fuel is used, it can lead to greatly reduced charac-

teris!cs and also cons!tute a poten!al health hazard with risk of personal injury. Faults that arise

due to use of incorrect fuel are not covered by the guarantee. If you feel uncertain, consult with the

personnel at the place of sale in order to ensure purchase of the right fuel quality.

4.2.2•Re illing•with•fuel

Warning! Denatured ethanol burns with an almost invisible #ame under certain condi!ons. This

may happen, for example, when the level in the burner is low. Therefore it is very important that the

ﬁreplace is ex!nguished completely a$er use, and that it is allowed to cool for at least 15 minutes

before more fuel is added. To add fuel in a burning ﬁreplace is very dangerous and can cause an

explosion.

Note 1! Add fuel when the ﬁreplace is about to be used – the burner has a safety func!on that makes

it harder to start when the fuel has been standing for more than 20 minutes. Read more at point 4 in

Sec!on 4.1 Ligh!ng the "replace.

Note 2! The burner may contain fuel from previous ﬁring. The tank’s total volume is 2 litres.

Therefore, do not add more than is needed according to point 5 below.

The following steps should be taken when adding fuel:

1. See that the ﬁreplace is completely ex!nguished, by checking that the regulator lid is closed, and

that the ﬁreplace has been allowed to cool for at least 15 minutes with the lid closed.

2. Check that the correct fuel is used. Vauni recommends that the ﬁreplace be ﬁlled from bio-

ethanol packaged in bo#les of 1 litre.

3. Open the regulator lid completely. Start ﬁlling by holding the bo%le to the burner’s opening,

angled so that the fuel ﬂows in the burner’s length direc!on, from right to le$ or vice versa. In

order to reduce the risk of spillage, IT IS RECOMMENDED TO USE A FUNNEL. (Figure 19) Pour the

fuel carefully down into the burner matrix. Add carefully un!l fuel is no longer absorbed by the

burner matrix. The liquid level must not rise above the burner matrix by more than 1 mm. (Figure

19 20

M A X

14) Then the burner is fully tanked, which corresponds to 2 litres of bioalcohol.

Note! For safety reasons the fuel transfer occurs with some delay. To avoid over-!lling the burner,

it is important to give the fuel "me to se#le downward. Be especially careful, therefore, during

the last part of the !lling. Let the bo#le drip a li#le over the opening before removing it.

4. Be careful to avoid all spillage – any spill should be wiped o$ with a piece of paper. If over-!lling

occurs, use suitable utensils to remove excess fuel, so that the fuel comes level with the burner

matrix.

The liner is sensi"ve to fuel spillage. It is therefore important that the !lling is done carefully, and that

a dry rag or paper is used to wipe o$ the bo#le immediately a%er !lling. If spillage does occur in spite

of this, it should be wiped o$ immediately, since dried fuel can cause permanent spots.

4.2.3•Handling•of•spillage

Avoid all spillage as far as possible. Take good "me when re!lling. If an accident does occur, observe

the following.

Note! Large amounts of spillage are caught by a built-in spillage tray. If this has happened, it is very

important to carry out the following restora"on procedure – do not light the !replace before then&

1. Immediately wipe o$ the liner with a dry rag in order to avoid discolouring.

2. Take out the burner module.

3. Wipe up the collected fuel with a rag or the like. See that the whole space is completely cleaned.

4. Lower the burner module by following instruc"ons in sec"on 3.1 Assembly and installa•on, step

12. See that the regulator lid is posi"oned correctly.

5. Do not light the !replace within at least 24 hours, in order to allow complete ven"la"on of the

spillage tray from any remaining fuel.

4.3•Extinguishing•the• ireplace

The !replace is ex"nguished by !rmly moving the regulator lid with the regulator rod so that it covers

the burner’s opening, which stops the oxygen supply to the 'ames. Let the lid stay closed un"l the

!replace is to be used again. Keep watch on the !replace to be sure that the !re is out. Before the

!replace can be lit again, it must cool for at least 15 minutes.

4.4•To•keep•in•mind•during•the• ireplace’s•operation

• Focus on safety.

• Do not leave the !replace una#ended for a long "me.

• Do not allow children or animals to come near the !replace while it is opera"ng. Make sure that

children understand the risk of burning themselves.

• Allow only people who know the manual’s contents to start or regulate the !replace.

• Do not add fuel to the !replace while it is opera"ng.

• Only pure ethanol is suited as fuel for the !replace’s combus"on system, which is one of the

cleanest in the world for leisure !ring. Erroneous handling of the !replace, including cooking

food, can lead to faulty combus"on, which may cause personal injury.

5 Safety instructions

5.1•General

•Read carefully through the instruc!on book before use and follow the instruc!ons.

• Vauni takes no responsibility for damage that occurs in connec!on with the product’s use in other

ways than those speci"ed in this instruc!on book.

• The "replace must not be changed in any way. Only accessories that are approved by Vauni may

be used.

• Use only liquid denatured ethanol as fuel. Bio-alcohol in gela•nous form, or ethanol fuel for

automobiles such as E85, must not be used under any circumstances!

• Children and animals must be kept under watch and at a secure distance from the "replace.

• During "ring, parts of the "replace can become very hot – therefore, exercise great care.

• Always have an approved "re ex!nguisher accessible. Vauni recommends at least a 6 kg powder

type of "re ex!nguisher, class ABE. For further informa!on on suitable types, contact the rescue

service (in Sweden, www.raddningsverket.se).

5.2•Installation•and•use••

• The product is intended solely for indoor use.

• The "replace must not be installed in a space with a volume of less than 32 m3(equivalent #oor

area 13 m2).

• Installa!on must be in a space with normal ven!la!on (0,5 exchange of air per hour). If uncertain,

consult a ven!la!on expert.

• The ﬁreplace must not be used in spaces which are inﬂammable or at risk of explosion, according

to EN 60079-10 and SRVFS 2004:7. (Applies for Sweden – for other markets consult your

distributor)

• The ﬁreplace may be used only in spaces where the temperature is not normally higher than

room temperature – it must not be used in a rela!vely warm environment.

• Inﬂammable objects must not be placed within a distance of 1 metre from the ﬁreplace. (Figure

18)

• No foreign objects may be placed in or near the #ame, since this can a$ect the cleanness of

combus!on. Foreign objects include decora!ve stones and similar items.

• The ﬁreplace must be ﬁrmly a%ached to the ﬂoor.

• The ﬁreplace must not be used for cooking food.

• Fuel containers must not be stored close to the ﬁreplace.

min 1 metre

1 metre

• Any spilled fuel must be wiped o• carefully before the •replace is lit.

• Fuel must NEVER be added while the •replace is burning – the re•lling may be done at earliest 15

minutes a•er the •replace has gone out.

• Denatured alcohol must never be ex•nguished with water.

5.3•Service•and•maintenance

• The •replace may be repaired only by authorized places of service.

• Fuel spillage on liner parts must immediately be wiped up with a dry rag. If this is not done,

permanent discolouring can occur.

• Maintenance according to the instruc•ons in Sec•on 6 must be done in order to ensure the

•replace’s proper•es

6 Maintenance and care

This product is designed to require a minimum of maintenance and care with normal use. If the

following instruc!ons are followed, the "replace will keep its proper!es and appearance for a long

!me.

6.1•General•cleaning

With normal use, cleaning of the "replace’s mantle is limited to dus!ng o# its outer parts, which

can be done with a dry rag. If they are very dirty, a lightly moistened rag can be used, but cleaning

detergents should be avoided.

The burner and the liner parts require special care as follows.

6.2•The•burner•system

Since the stainless steel metal around the burner’s opening and the regulator lid is exposed to heat, it

will darken a$er some !me of use, which is quite natural. However, a dark coa!ng may appear inside

the burner tray and on the burner lid a$er some !me of use. This must be removed regularly in order

to ensure op!mal combus!on of the fuel.

The coa•ng is removed with the following steps:

•If the "replace has been used, it must be allowed to cool un!l the burner has reached room

temperature.

• Remove the regulator lid by li$ing it straight up.

• Scrape o# any coa!ng around or inside the burner tray, using a rubber or plas!c scraper. Take

special care around the burner matrix, and see that no par!cles fall down into the combus!on

chamber or block the holes in the burner matrix.

• Remove the scraped-o# coa!ng by using a vacuum cleaner.

• Clean the area around the burner tray’s opening with a moist rag. If it is very dirty, a mild

detergent can be used sparsely. In this case, be very careful that the liquid does not run down

into the burner matrix or make contact with the surrounding liner.

• Scrape o# any coa!ng from the regulator lid, then clean it o# with a moistened rag. If it is very

dirty, a mild detergent can be used sparsely.

• Place the regulator lid by lowering the two guide pins into the respec!ve grooves. When correctly

placed, the regulator lid should lie closely against the burner’s surface and slide easily when the

regulator rod (which grips in the holes provided in the regulator lid) moves it to its respec!ve

stop.

7 Fault •inding

The •replace cannot be lit

Possible causes:

• No fuel is in the burner module.

• The fuel level is too low.

• The burner’s safety system makes it hard to start.

• The fuel being used is incorrect, or has been diluted by excess cleaning liquid or the like.

• The regulator lid is not fully open.

Measures:

• Add fuel.

• Start the burner according to the instruc!on in Sec!on 4.1 point 4.

• Change the fuel. See Sec!on 4.2.1 for recommenda!ons.

• Move the regulator lid toward the "replace’s opening un!l it stops. If the burner opening is not

fully exposed, see the assembly instruc!ons to posi!on it correctly. If this does not help, contact

the place of purchase for the nearest service technician.

The •replace starts but goes out again

Possible causes:

• Low fuel level.

• The regulator lid is not fully open.

• The burner’s safety system makes it hard to start.

Measures:

• Repeat the star!ng procedure.

• Add fuel.

• Start the burner according to the instruc!on in Sec!on 4.1 point 4.

• Move the regulator lid toward the "replace’s opening un!l it stops. If the burner opening is not

fully exposed, see the assembly instruc!ons to posi!on it correctly. If this does not help, contact

the place of purchase for the nearest service technician.

The ﬂame is unstable or unusually large, or leans toward one side, or forms a strong vortex (whirl)

Possible causes:

• The #ame is exposed to a draught.

• The "replace is leaning

• The wrong type of fuel is being used.

Measures:

• An unusual #ame can result if the #ame is exposed to strong draught. This applies especially

to draughts from the side of the "replace. Try "rst to locate the source of the draught (open

window, fan, AC etc.) and stop it. If this is not possible, the "replace must be moved – see Sec!on

3.1 for instruc!ons about installa!on.

• The burner’s proper!es can be a$ected nega!vely if the "replace is leaning. Therefore, check this

with a liquid level. If the "replace is leaning, it must be posi!oned again.

• Change the fuel. See Sec!on 4.2.1 for recommenda!ons.

The ﬂames are sooty – a strange smell is emi"ed

Possible causes:

• A foreign object is present in the burner opening or near the #ames.

• The "replace is in a room with a strong draught or de"cient ven!la!on.

• The wrong type of fuel is being used.

• The burner is dirty.

Measures:

• Ex!nguish the #ames and let the "replace cool for 15 minutes.

• Posi!on the "replace again in a room that ful"ls the requirements speci"ed in Sec!on 4 Firing.

• Change the fuel. See Sec!on 4.2.1 for recommenda!ons.

• Clean the burner system by following the instruc•ons in Sec•on 6.2.

The ﬁreplace is not ex•nguished when the regulator lid is moved to the stop posi•on / something is

blocking the lid from reaching the stop posi•on.

Possible causes:

• The regulator lid is blocked.

• The regulator lid is not moved fast enough to the stop posi•on.

• The regulator mechanism has been damaged by external in!uence.

Measures:

• Check that the regulator lid is correctly placed (see instruc•ons in Chapter 3.1 Assembly and

installa•on).

• If the regulator lid is correctly posi•oned, remove it from the burner module and check that no

foreign object is blocking the grooves or stuck to the regulator lid. Also check that the lid is not

bent.

• Test moving the regulator lid to the maximum posi•on and then moving it "rmly to the stop

posi•on.

• If this does not work, let the "replace burn out and then allow it to cool for at least 15 minutes.

• If the above does not help, contact the place of purchase for further contact with a service

technician.

The ﬂame burns uncontrollably for some reason

Possible causes:

• A fault has occurred in the burner system.

• The wrong type of fuel is being used.

• The "replace is exposed to a very strong draught.

• The "replace is not installed in accordance with the instruc•ons in Chapter 3.1 Assembly and

installa•on.

Measures:

The "replace is designed and built, as well as thoroughly tested, to func•on safely even in abnormal

situa•ons. In the unlikely event that the "replace burns uncontrollably, the recommenda•ons are as

follows:

• Try to ex•nguish the "re by moving the regulator lid toward the "replace’s opening un•l it stops.

• If this has no e#ect, the "replace should primarily be allowed to burn out – provided that the

!ames stay inside the "replace and do not reach the inner side of the Edge/Shadow.

• If the !ames are so strong that the "replace cannot be allowed to burn out, it must be

ex•nguished with a hand-held "re ex•nguisher. For more informa•on about suitable models of

"re ex•nguisher, contact the rescue service (in Sweden, www.raddningsverket.se).

The regulator lid does not ﬁt •ghtly against the burner disk

Possible causes:

• The regulator lid is wrongly posi•oned.

• A foreign object is present between the regulator lid and the burner disk.

• The regulator lid and/or the burner disk is dirty.

Measures:

• Posi•on the regulator lid according to the instruc•ons in Sec•on 3.1 Assembly and installa•on.

• Remove any foreign objects.

• Li$ o# the regulator lid and clean it. If necessary, also clean the burner disk and the burner

opening.

The ﬁreplace leaks a"er fuel is added

Possible causes:

• The burner is over-"lled.

• A leak has arisen in the burner system.

• The fuel has expanded in a warm state – the burner is over-"lled

Measures:

All parts of the burner system are made of high-quality stainless steel and carefully checked against

leakage before delivery. If a leak is observed or suspected, the •replace must immediately be

ex•nguished and not used un•l the fault is •xed.

• If the burner has been over-•lled, excess fuel must be removed by following the instruc•ons in

Sec•on 4.2.3.

• If the burner system leaks, the •replace must not be lit under any circumstances. Contact the

place of purchase for the nearest service workshop.

8 Technical speci•ications

Dimensions 950x550x160 (170) mm (w h d)

Weight 25-30 kg

Eﬀect 2 kW (max)

Fuel tank volume 2 litres

Fuel consump"on 0.4 litre/h (max eﬀekt)

Burning "me min 4-5 h (full tank)

Type of fuel liquid denatured ethanol

Min. room volume 32 m3

Min. ﬂoor area 13 m2

Tools

Data Outside dimensions (mm)

550

950

160

550

950

170

Manual

Vauni Edge/Shadow

Vik•gt!

Läs igenom hela manualen och ägna särskild uppmärksamhet åt säkerhetsanvisningarna innan

produkten tas i bruk.

ENG/ SVE

Version SE42-1411

Innehåll

1 Introduk•on..........................................................................................................................................1

2 Beskrivning av eldstaden......................................................................................................................2

3 Installa•on............................................................................................................................................3

3.1 Montering och installa•on..........................................................................................................3

4 Eldning..................................................................................................................................................6

4.1 Tändning av eldstaden ................................................................................................................6

4.2 Bränsle ........................................................................................................................................6

4.2.1 Rekommenderad bränslekvalitet .............................................................................................6

4.2.2 Påfyllning av bränsle................................................................................................................7

4.2.3 Hantering av spill .....................................................................................................................8

4.3 Släckning av eldstaden................................................................................................................8

4.4 A! tänka på när eldstaden är i dri" ............................................................................................8

5 Säkerhetsanvisningar............................................................................................................................9

5.1 Allmänt........................................................................................................................................9

5.2 Installa•on och användning ........................................................................................................9

5.3 Service och underhåll................................................................................................................10

6 Underhåll och skötsel .........................................................................................................................11

6.1 Generell rengöring ....................................................................................................................11

6.2 Brännarsystemet .......................................................................................................................11

7 Felsökning...........................................................................................................................................12

8 Tekniska speci#ka•oner......................................................................................................................15