VCS VideoJet 100 User manual

100series
VCS
Manual for
C 100
VideoJet 100
VideoJet 400
VideoJet 400 19’’

Copyright This manual is the intellectual property of VCS and is protected by
copyright. All rights are reserved. No part of this document may be
reproduced or transmitted for any purpose, by whatever means, be
they electronic or mechanical, without the express written permis-
sion of VCS.
Edition: December 2002 (Version 6.0)
© Copyright 2002 VCS Video Communication Systems AG
Note This manual was compiled with the greatest of care and all informa-
tion double checked. At the time of printing the description was
complete and correct. Because of the further development of pro-
ducts, the content of the manual might change without prior notice.
VCS will not be liable for damage which is directly or indirectly due
to errors, incompleteness, or discrepancies between the manual
and the product described.
Trade marks All names used in this manual for hardware and software are very
probably registered trade marks and must be treated as such.

1
VCS 100series
Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Chapter 1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
EU Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rating plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 2 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical shock hazard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Repairs and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter 3 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Preconditions for commissioning . . . . . . . . . . . . . . . . . . . . . . . 12
Preconditions for configuration . . . . . . . . . . . . . . . . . . . . . . . . . 12
Preconditions for operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Overview of functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connectors, controls and LEDs . . . . . . . . . . . . . . . . . . . . . . . . 20
Chapter 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Installing the C 100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Further connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Installing the VideoJet 100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Content

Content
2
VCS 100er Serie
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Installing VideoJet 400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Cabinet installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Switching on / Switching off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Commissioning
with terminal program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Chapter 5 Configuration with
web browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Making the connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Selecting the configuration mode . . . . . . . . . . . . . . . . . . . . . . . 50
Installation wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Expert Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Function test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Chapter 6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Operation with
MS Internet Explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Making and storing snapshots . . . . . . . . . . . . . . . . . . . . . . . . . 100
Storing MPEG sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Replay of DRAM recordings . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Hardware connections
between VCS Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Operation with Software-Decoder . . . . . . . . . . . . . . . . . . . . . . 106
Chapter 7 Care and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Checking the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Further sale, disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Content
3
VCS 100series
Chapter 8 Annex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Faults – possible causes and remedy . . . . . . . . . . . . . . . . . . . 109
LEDs C 100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
LEDs VideoJet 100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
LEDs VideoJet 400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Chapter 9 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Content
4
VCS 100er Serie

5
VCS 100series
Preface
1
These Installation and Operating Instructions are intended for per-
sons authorised to install and operate a VCS 100series device.
This series consists of the IP camera C 100 and the Network Video
Servers VideoJet 100 and VideoJet 400 including all device alter-
natives. International, national and any relevant regional regula-
tions relating to electronics must be observed at all times. The
Operating Instructions explain the installation and operation of all
VCS 100series devices.
Conventions
In this manual, the following symbols and notations are used to
draw attention to special situations:
Hazard! or Attention!
This symbol indicates that failure to follow the safety instructions
given may directly endanger people, cause damage to the system
or to other equipment. The symbol represents a direct threat of dan-
ger.
Note
This symbol indicates tips and notes that make using the device
easier and more convenient.

Preface
6
VCS 100series
The following typographic conventions are used in this manual:
The description is based on the VideoJet 400. Only where
VideoJet 100 resp. C 100 differ regarding basic functions these
particularities are specified.
Note
This symbol indicates that you might have to find out special infor-
mation to be able to make the settings or start up the system cor-
rectly.
Configuration Menu names and window and key names and
parameters
[Enter], [C] Key names
[Ctrl] + [C] Two or more keys that are pressed simul-
taneously.
ping Command line input and output

Preface
7
VCS 100series
Intended use
The IP camera C 100 serves to transmit video and control signals
via data networks (Ethernet LAN).
The Network Video Servers VideoJet 100 and VideoJet 400 serve
to transmit video, audio and control signals via data networks (Eth-
ernet LAN).
All devices are designed for use in CCTV systems. The connection
of an external alarm generator allows various functions to be trig-
gered automatically. Other applications are not permitted.
In the event of questions concerning the use of the device which are
not answered in this manual, please contact:
VCS Video Communication Systems AG
Forchheimer Straße 4
90425 Nürnberg, Germany
Phone [phone]
Fax [phone]
[email protected]
EU Guidelines
The IP camera C 100 and the Network Video Servers VideoJet 100
and VideoJet 400 comply with the specifications of European
Guidelines 89/336 (Electromagnetic Compatibility) and 73/23,
amended by 93/68 (Low-Voltage Guideline).
Rating plate
For exact identification, you will find the model designation and
serial number on the rating plate on the bottom of the housing.
Please note this information here before installation in order to have
it on hand in the event of queries or spare parts orders.

Preface
8
VCS 100series

9
VCS 100series
Safety information
2
Electrical shock hazard
!Never attempt to connect the unit or the mains power supply to
any power network other than the one for which it was intended.
!Use only appropriate and approved power supply units for the
C 100 (see technical specifications) resp. the mains lead sup-
plied with the VideoJet 100 and the VideoJet 400.
!Do not open the housing of the power supply unit.
!Disconnect the power supply unit from the mains power supply
and from all other devices if a fault occurs.
!Install the power supply unit and the unit only in a dry place
protected against the elements.
!If you are uncertain about the safe operation of the unit, shut it
down immediately and secure it to prevent any unauthorised
start-up. Safe operation is no longer possible, for example,
– if damage is visible to the unit or the cables,
– if the unit no longer operates correctly,
– if the unit has been exposed to rain or moisture,
– if objects have penetrated inside the unit,
– after long storage under improper conditions or
– after heavy demands during transport.
Have the system checked by VCS in such cases.

Safety information
10
VCS 100series
Installation and operation
!All applicable electrical codes and regulations must be observed
and followed at all times during the installation.
!Before installing or operating the system, ensure that you have
read and understood the documentation for other equipment
connected to the unit, e.g. monitors or pan-and-tilt heads. These
contain important safety notices and information concerning per-
missible applications.
!Perform only the installation and operating work described in this
manual. All other work beyond this may lead to injuries to per-
sons and damage to the system or other equipment.
!Ensure a secure footing whenever working in elevated positions
(e.g. under the ceiling, on masts, etc.). Use only safety ladders.
If necessary, use a safety harness or railings.
Repairs and maintenance
!Never open the housing of the unit. The unit contains no parts
which you can repair or replace.
!Never open the housing of the power supply unit. The power
supply unit contains no parts which you can repair or replace.
!Ensure that only qualified, specialist personnel (electrical tech-
nicians) are permitted to carry out maintenance or repair work.
Attention!
Close to high frequency electromagnetic fields the audio output
signal of the VideoJet units may be distorted.

11
VCS 100series
Product description
3
Scope of delivery
C 100 !IP camera C 100
!4-pin plug kit
!CD with VCS software and manual german/english
!Brief description ’Quick Set-up Guide’ german/english
VideoJet 100 !VideoJet 100 desktop device, incl. plug-in power pack
!CD with VCS software and manual german/english
!Brief description ’Quick Set-up Guide’ german/english
VideoJet 400 !VideoJet 400 desktop device, incl. plug-in power pack
or
!VideoJet 400 cabinet version
with integral power supply, incl. power cord
!CD with VCS software and manual german/english
!Brief description ’Quick Set-up Guide’ german/english

Product description
12
VCS 100series
Preconditions for commissioning
!Computer with operating system Windows 98/2000/XP and a
gateway to the network
!Microsoft Internet Explorer web browser (from Version 5) or free
serial interface and terminal program
Preconditions for configuration
!Computer with operating system Windows 98/2000/XP and a
gateway to the network
!Microsoft Internet Explorer web browser (from Version 5) or
Receiver software e.g. VIDOS from VCS
Preconditions for operation
!Computer with operating system Windows 98/2000/XP and a
gateway to the network
!Microsoft Internet Explorer web browser (from Version 5) or
Receiver software e.g. VIDOS from VCS
or
!Receiver VideoJet 100 or VideoJet 400 and video monitor

Product description
13
VCS 100series
Overview of functions
Color camera
C 100
The IP camera C 100 is a high-resolution color camera for profes-
sional use in CCTV systems. It has an integral video server for
encoding of the video and control signals for the transfer via an
Ethernet LAN. By using existing networks, the C 100 permits the
simple installation and configuration of CCTV systems.
The camera's 1/3“ CCD offers a horizontal resolution of 470 (PAL)
resp. 480 (NTSC) lines. The camera is characterised by its excep-
tional dynamic range of more than 46 dB and its highly sophistica-
ted backlight compensation. Interference with strong backlight
which causes under-exposure and extensive loss of detail with nor-
mal cameras is thus effectively eliminated.
The digital signal processor in conjunction with an intermediate
image memory allows the light sensitivity to be increased by up to
32 times, hence significantly extending its range of potential appli-
cations compared with standard cameras. The camera is therefore
extremely well-suited for use in environments with poor lighting
conditions or in extreme light situations (e.g. strong backlight from
floodlights or reflected sunlight).
All the camera parameters are conveniently set via the HTML
pages using an internet browser.
The maximum camera performance is obtained by using lenses
with DC-controlled iris which guarantee an optimum light-source
efficiency.
The main functions of the camera include:
!DC iris control
!Wide dynamic range
!Automatic white balance
!Electronic shutter
!Backlight compensation
!Automatic gain control (AGC)
!Setting of the color saturation

Product description
14
VCS 100series
!Video signal enhancer
!Increased light sensitivity
Network video
server
VideoJet 100 and
VideoJet 400
The VideoJet 100 and the VideoJet 400 are network video
servers. They serve primarily for encoding and decoding video,
audio and control data for transfer via an Ethernet LAN. By using
existing networks, the devices permit the simple installation and
configuration of CCTV systems.
The VideoJet 100 is available in two versions, as transmitter and
as receiver.
The VideoJet 400 is available in two versions, as a desktop device
with separate plug-in power pack and in a control cabinet version
with integral power pack. Whereas the desktop device is available
as a data server only for transmission of data, transmitting and
receiving of data are possible with the control cabinet version.
Stand-alone
system
Two VCS 100series devices, e.g. a C 100 or a VideoJet 400 as
transmitter and a VideoJet 100 receiver, can form a stand-alone
system for data transfer without PC. The system can be extended
to include further transmitters and receivers so that video
sequences from several transmitters can be received by several
receivers.
Receiver The corresponding VideoJet 100 devices or the VideoJet 400
(control cabinet version) or computers with installed decoding soft-
ware, for example VIDOS from VCS, or with installed Microsoft
Internet Explorer can always be used as receivers.
Note
The maximum camera performance can only be obtained in
conjunction with the corresponding periphery. For optimum use of
the functions of the digital signal processor, the lens must have a
DC-controlled iris.

Product description
15
VCS 100series
Multicast function All devices of the VCS 100series support the standard MPEG-4.
Thanks to efficient encoding, the data transmission rate remains
low, even with maximum image quality and 30 images/s; further-
more, it can be adapted over a wide range to meet the local require-
ments.
In appropriately configured networks, the multicast function permits
the simultaneous video transmission in real time to several recei-
vers. A precondition for this is the implementation of the UDP and
IGMP protocols in the network.
Integral
multiplexer in the
VideoJet 400
The VideoJet 400 is designed for the connection of four freely
selectable video sources (4× PAL or 4× NTSC). With the appropri-
ate software on the receiver side, e.g. VIDOS from VCS or the
Microsoft Internet Explorer, four camera images can be viewed
simultaneously in this way.
Remote control For remote control of external equipment, e.g. pan-and-tilt heads or
motorised zoom lenses, the control data is transmitted via the bidi-
rectional serial interfaces of the units. These interfaces can also be
used for the transmission of transparent data.
Configuration The VCS 100series units can be configured with a browser via the
local network (Intranet) or via the Internet. Firmware updates and
the quick uploading of device configurations are possible in the
same way.
Recording,
playback
You can save live pictures recorded by the unit as files on the hard
disk of your computer. The video pictures are stored in MPEG
format and can, for example, be replayed with the VCS MPEG
Player included in delivery.
The RAM memory integrated in the unit serves as pre-alarm
memory. On this ring buffer video pictures are recorded as long as
there is no active connection to a receiver unit.

Product description
16
VCS 100series
Snapshot You can save an individual video picture (snapshot) on your com-
puter’s hard disk, or call one up from the camera in JPEG format and
display it in a separate browser window.
Backup You can transfer recordings made on the unit’s RAM to your com-
puter and save them there as a backup. The video pictures are
stored in MPEG format and can, for example, be replayed with the
VCS MPEG Player included in delivery.

Product description
17
VCS 100series
Summary C 100 The IP camera C 100 offers the following main functions:
!Video and data transmission via data networks
!Digitally optimized video data
!Automatic iris control
!Multicast function for simultaneous image transmission to
several receivers
!Transmission of the video images (PAL or NTSC compatible) as
high-resolution individual frames or sequences
!Local video output PAL or NTSC (depending on version)
!High color image resolution with 704 × 288 pixels
!Refresh rate of up to 30 images/s
!Video transmission compatible with international standards
MPEG-4 and M-JPEG
!Integral Ethernet interface (10 Base-T)
!Transparent bidirectional data channel via serial interface
RS232/RS422/RS485
!Remote control of all internal functions via TCP
!Three-step password protection to prevent unauthorised access
!Switching input for external sensor (e.g. door contact)
!Switching output for switching an external device (e.g. light
or siren)
!Event-controlled automatic connection setup (e.g. when
switching on and at alarms)
!Integral video sensor for motion alarms
!Video signal monitoring
!Automatic transmission of alarm e-mails with attached image
!Internal RAM ring memory for recording of pre-alarm history
!Quick and convenient configuration via web browser
!Firmware update via flash memory

Product description
18
VCS 100series
Summary
VideoJet 100
The VideoJet 100 offers the following main functions:
!Video, audio and data transmission via data networks
!Multicast function for simultaneous image transmission to
several receivers
!1 video channel (PAL and NTSC compatible), transmission of
the video images as high-resolution individual frames or image
sequences
!High color image resolution with 704 × 288 pixels
!Refresh rate of up to 30 images/s
!One audio input, one audio output
!Video transmission compatible with international standards
MPEG-4 and M-JPEG
!Integral Ethernet interface (10/100 Base-T)
!2 transparent bidirectional data channels via serial interfaces
RS232/RS422/RS485 and RS232
!Remote control of all internal functions via TCP
!Three-step password protection to prevent unauthorised access
!Switching inputs for external sensors (e.g. door contacts)
!Switching outputs for switching external devices (e.g. lights or
sirens)
!Event-controlled automatic connection setup (e.g. when
switching on and at alarms)
!Integral video sensor for motion alarms
!Video signal monitoring
!Automatic transmission of alarm e-mails with attached image
!Video ring memory for recording of pre-alarm histories
!Quick and convenient configuration via web browser
!Software update via flash memory