Ganz Thermal ZNT1-H Series User manual

CBC AMERICAS CORP. - EAST COAST [phone] | WEST COAST [phone] | MEXICO [phone]
ganzsecurity.com. 01/17
1
ZNT1-H Series Quick Start Guide
Before installing and operating the unit, please read this manual
thoroughly and keep it for future reference.
About the manuals
This manual provides the instructions for the quick installation
and the basic configuration of your IP device. For more detailed
information, refer to the camera’s installation guide and the web
page user’s manual.
Part names and functions
Please check the name and position of each part by
referring to the following image.
Sunshield: It prevents the lens from getting the direct sunlight.
NTSC / PAL Button: The button switches the video output mode between
NTSC and PAL. Pressing the button will maintain the current video output
mode unless pressing again to switch to the other mode.
Analogue Video Output: Connect a video output cable to see video via an
analogue monitor.
RJ45 Socket: RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported)
Reset Button: Press the button either for the restart or the factory default
of the device. For restart, 1.press the button only for 2 seconds while the
device is powered on. 2.Wait for the system to reboot. For factory default,
1.press the button for 10 seconds while the device is powered on. 2.Wait for
the system to reboot. There are also the methods performed on the
camera’s web page. Refer to the Reboot and Factory Default section in this
manual.
Terminal Connectors for DI/DO: Connector for audio input (sensor) and
audio outputs (alarms). Refer to the Connection section for more
information about the characteristics of DIDO in the installation guide.
Terminal Connectors for Audio I/O: Connector for audio input (MIC) and
audio output(speaker). Refer to the Connection section for more
information about the characteristics of audio in the installation guide.
Terminal Connectors for RS-485: Connector for RS-485. Refer to the
Connection section for more information about the characteristics about RS-
485 in the installation guide.
Terminal Connector for power adaptor: Connector for power supply
(12VDC, 24VAC, and PoE supported).
Installation
Installing Cable Gland
To meet the IP66 requirements, you need to install the cable gland unit to
the camera. Follow the instructions on the other side of this page.
Connecting Cable(s)
Refer to the connection section for more information about each connector.
Installing Base Mount
Connecting Cables
For the information about the necessary cables, refer to the part names and
functions section on the left side of this page and the Connection section in
the installation guide.
Closing Back Cover
Installing Sunshield
Terminal
connectors
for power
adaptor
Sunshield
1) Detach the back cover by twisting it counter-clockwise.
2) Disassemble the cable gland unit
(Disassembled parts: electrical nut, rubber sealing
ring inside the gland - you need to take it out, gland body, and sealing nut).
3) Pass the electrical nut through the ends of the necessary cables.
4) Pass the cables through the holes both on the back and the bottom of
the camera by referring to the image above.
5) Pass the provided O-ring, gland body through the ends of the cables
that are on the backside of the camera.
6) Insert the cables into the rubber sealing ring at the point where about
4.5 inches (11.5 cm) of the cable ends remains to connect to the
corresponding connectors on the back panel later.
7) Push the rubber sealing ring through the claw of the gland body.
8) Insert the sealing nut into the thread of the gland body, and tighten it
by turning the nut on the thread. The rubber sealing ring will be tightened
to fill the gap between the rubber sealing ring and the cables.
9) Push the gland unit through the hole on the back of the camera so that
the other end of the thread on the gland unit will be inserted into hole for
gland.
10) Fix the gland unit to the hole by inserting the electrical nut and
tightening it on the thread of the gland unit.
NOTE1
A thin type of the BNC cable is recommended when you insert
multiple cables including a BNC cable as the standard size of BNC cable is
too thick to be inserted together into the rubber sealing ring.
NOTE2
Use the detachable cable with a separate BNC connector to pass
the hole of the sealing nut or the female type head of the BNC cable to
pass the hole of the sealing nut.
1) Insert the provided
8 tamper resistant
screws to the
corresponding screw
holes on the base
mount by referring to
the image on the right.
2) Tighten them with
a Phillips head #2
screwdriver to fix the
base mount to the
camera.
1) Insert the provided
silica gel packet inside
the back panel.
2) Close the back
panel of the camera
by twisting the back
cover clockwise
on the camera’s back
panel.
3) Insert the two tamper
resistant screws into the
holes on the back cover,
and tighten them with a
Phillips #2 screwdriver
to fix the back cover to
the camera unit.
* The model herein and its appearance are subject to change without any prior notice.
NTSC / PAL button
Analogue video output
RJ45 socket
Reset button
Terminal connectors
for DI/DO
Terminal connectors
for Audio In/Out
Terminal connectors
for RS-485
[ Back Panel of Camera ]
Electrical nut
Hole for gland
O-ring
Gland body
Sealing nut
[Base Mount Installation: Upside-Down View]

CBC AMERICAS CORP. - EAST COAST [phone] | WEST COAST [phone] | MEXICO [phone]
ganzsecurity.com. 01/17
2
Installing with Bracket/Adaptor
There are currently 7 optional accessories such as wall mount bracket,
corner mount bracket, and so on. Please refer to the corresponding
accessory’s installation guide for the installation instructions.
Setting up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify
the IP address of the device by converting the MAC address’s hexadecimal
numbers. The MAC address is at the bottom of the device. Be sure that the
device and the PC are on the same network area before the installation.
Generic IP Environment
Convert the device’s MAC address to the IP address. Refer to the
Hexadecimal-Decimal Conversion Table at the end of this manual.
IPAdminTool
IPAdminTool is a management tool to automatically scan all the network
products for the devices’administrative tasks, which include network
configurations, firmware update, device reboot, factory default, and device
organization.
To modify the device’s default IP address for a customized network area;
1) Find the device from IPAdminTool’s list, and highlight the device’s name.
2) Right-click the mouse, and select IP Address, and select either Single or
Multiple depending on the selected number of devices.
3) Type the new network information including IP Address. The image above
shows the Single IP Change window only. Refer to the manual for
IPAdminTool in case you need the instructions to change multiple IP
addresses.
4) Enter ID and PW(if the device’s ID and PW have never been changed,
check the checkbox of ‘Use default ID/PW’.)
5) Click Apply.
Viewing video on web page
Once the device’s IP address has been identified, type the URL in a web
browser to access the camera. At the first time access, the installation
window like below may pop up.
1) When the browser asks to install the AxUMF software, click Install to
proceed.
2) When the Setup installation pop-up window appears, click Install to
preceed with the rest of the installation.
SETUP page
To setup the device configuraiton:
1) Click Setup on the upper left corner of the web page.
2) Enter the user name and the password when the login page is displayed.
(The default user name and the password are root and pass.)
3) Click OK.
To learn how to set up the camera on the web page for the advanced
configurations, refer to the web page user’s manual.
Reboot*
You can reboot the device via the camera’s webpage, too.
1) Go to Setup > Maintenance > Reboot.
2) Click Reboot to reboot the device.
Factory Default*
You can initialize the current settings to the factory default values via the
camera’s webpage, too.
1) Go to Setup > Maintenance > Reset All Settings.
2) Select the items that you want to keep from the initialization among
network settings, user account information, and time zone setting.
3) Click Reset All Settings.
Safe mode
Your device will get restarted in safe mode if the device does not completely
boot certain times. The main causes for safe mode are as follows.
* The power supply is continually unplugged certain times in the middle of system
booting.
* The firmware files required for system booting are damaged.
* There are conflicts in the system settings.
You will see the page to indicate that your device is in safe mode and to
guide you what to do in steps. Follow the instructions on the webpage
according to each step.
NOTE
One of the methods to update firmware is using IPAdminTool. Please refer
to the manaul for IPAdminTool for the detailed procedure.
NOTE
If your device is still in safe mode after trying to update firmware, please
contact your local agency to get further assistance.
Hexadecimal-decimal conversion table
Refer to the following table when converting the MAC address of your device
to IP address.
Hex
Dec
Hex
Dec
Hex
Dec
Hex
Dec
Hex
Dec
Hex
Dec
Hex
Dec
0
0
25
37
4A
74
6F
111
94
148
B9
185
DE
222
1
1
26
38
4B
75
70
112
95
149
BA
186
DF
223
2
2
27
39
4C
76
71
113
96
150
BB
187
E0
224
3
3
28
40
4D
77
72
114
97
151
BC
188
E1
225
4
4
29
41
4E
78
73
115
98
152
BD
189
E2
226
5
5
2A
42
4F
79
74
116
99
153
BE
190
E3
227
6
6
2B
43
50
80
75
117
9A
154
BF
191
E4
228
7
7
2C
44
51
81
76
118
9B
155
C0
192
E5
229
8
8
2D
45
52
82
77
119
9C
156
C1
193
E6
230
9
9
2E
46
53
83
78
120
9D
157
C2
194
E7
231
0A
10
2F
47
54
84
79
121
9E
158
C3
195
E8
232
0B
11
30
48
55
85
7A
122
9F
159
C4
196
E9
233
0C
12
31
49
56
86
7B
123
A0
160
C5
197
EA
234
0D
13
32
50
57
87
7C
124
A1
161
C6
198
EB
235
0E
14
33
51
58
88
7D
125
A2
162
C7
199
EC
236
0F
15
34
52
59
89
7E
126
A3
163
C8
200
ED
237
10
16
35
53
5A
90
7F
127
A4
164
C9
201
EE
238
11
17
36
54
5B
91
80
128
A5
165
CA
202
EF
239
12
18
37
55
5C
92
81
129
A6
166
CB
203
F0
240
13
19
38
56
5D
93
82
130
A7
167
CC
204
F1
241
14
20
39
57
5E
94
83
131
A8
168
CD
205
F2
242
15
21
3A
58
5F
95
84
132
A9
169
CE
206
F3
243
16
22
3B
59
60
96
85
133
AA
170
CF
207
F4
244
17
23
3C
60
61
97
86
134
AB
171
D0
208
F5
245
18
24
3D
61
62
98
87
135
AC
172
D1
209
F6
246
19
25
3E
62
63
99
88
136
AD
173
D2
210
F7
247
1A
26
3F
63
64
100
89
137
AE
174
D3
211
F8
248
1B
27
40
64
65
101
8A
138
AF
175
D4
212
F9
249
1C
28
41
65
66
102
8B
139
B0
176
D5
213
FA
250
1D
29
42
66
67
103
8C
140
B1
177
D6
214
FB
251
1E
30
43
67
68
104
8D
141
B2
178
D7
215
FC
252
1F
31
44
68
69
105
8E
142
B3
179
D8
216
FD
253
20
32
45
69
6A
106
8F
143
B4
180
D9
217
FE
254
21
33
46
70
6B
107
90
144
B5
181
DA
218
FF
255
22
34
47
71
6C
108
91
145
B6
182
DB
219
23
35
48
72
6D
109
92
146
B7
183
DC
220
24
36
49
73
6E
110
93
147
B8
184
DD
221
1) Insert the two provided
stembumpers to the holes
at the bottom of the
sunshield.
2) Place the sunshield on
top of the camera body,
and, snap the sunshield
to the base mount.
MAC address = 00-13-23-01-14-B1 -> IP address = 192.168.20.177
Convert the last two sets of hexadecimal numbers to decimal numbers.
1 CH En coder
1 CH Encoder
1 CH Encoder
1 CH Encoder
1 CH Encoder
1 CH Encoder
1 CH Encoder
1 CH Encoder
1 CH Encoder
1 CH Encoder
1 CH Encoder
1 CH Encoder
1 CH Encoder
1 CH Encoder
1 CH Encoder
1 CH Encoder
Encoder1
Encoder2
Encoder3
Encoder4
Encoder5
Encoder6
Encoder7
Encoder8
Encoder9
Encoder10
Encoder11
Encoder12
Encoder13
Encoder14
Encoder15
Encoder16
Current PC environment Info
Give a new unique IP address in the last two sets
and mirror other information in the other boxes.
*How to reboot on the device is found in the part names and functions section on the previous page.
*How to do factory default on the device is found
in the Part names and functions section on the previous page.