VDO AcquaLink A2C59501997 User manual

AcquaLink - 7” TFT display
Instruction manual
v. 1.0

Contents
Getting started 4
Data pages 8
Data page configuration 12
General settings 18
System settings 20
Alarm management 24
Sensor configuration 29
Management of network devices 36
MediaBox use 41
VDO Marine Configuration Tool use 47
Troubleshooting 48
Technical specifications 50
Spare parts, sensors and accessories 51
Updated and multilingual instructions available
These instructions are always updated and available in several
languages at www.vdo-marine.com.
Accompanying documentation
The instructions for installing and using Nav Box and Nav Control are
available at www.vdo-marine.com, document codes:
lNav Box: A2C12119500
lNav Control: A2C99832800
Customer service and warranty
In the event of malfunction, fault or for information on the warranty,
contact a VDO partner. To find a partner, visit www.vdo-partner.com.
III

Getting started
Description
AcquaLink 7" is a multifunctional display connected to the VDO CAN bus network of the AcquaLink
system. The display lets you view data from the engines and the sensors connected to Nav Box through
NMEA 2000, NMEA 0183, SAE J1939 or directly connected through analog inputs. Up to four engines can
be monitored from the display.
The Nav Control remote control is necessary to interact with the display.
4 7” TFT display | Instruction manual v. 1.0 | © 2018 Continental Automotive Switzerland AG

Operations
AcquaLink 7" is a versatile device. It lets you control all the engines connected to Nav Box in a single
monitoring point and at the same time.
Select the number of engines on the boat when first turned on or when reset. If the selected number of
engines is different from the installed engines, only the data of the selected engines will be displayed. The
number of engines can be changed later (see "Change the number of engines to be displayed" on page17).
Received signal priority
If the same data is transmitted by more than one signal for the same engine, the received signal priority is
the following:
1. Analog input
2. NMEA 2000
3. SAE J1939
4. NMEA 0183
On/Off
The on/off mode depends on the connection made during installation.
The VDO logo and software version followed by the AcquaLink logo appear when turned on. In addition, if
before turned off the display was controlled by Nav Control or if on the VDO CAN bus network there is only
one display, the Nav Control icon appears.
The display prompts you to select the type of boat and the number of engines to be monitored when first
turned on or when reset.
Function of the display buttons
Button Function
Briefly press:
lAccess favorite groups 1, 2 and 3.
Getting started
57” TFT display | Instruction manual v. 1.0 | © 2018 Continental Automotive Switzerland AG

Function of the Nav Control buttons
Button Function
Hold down:
lTurn on/off Nav Control and all the devices connected to
the VDO CAN bus network
Briefly press:
lChange the display brightness level
Hold down:
lChange the color of the background and of the characters
on the display
Briefly press:
lReturn to the previous menu level
Hold down:
lReturn to the last data page displayed
Briefly press:
lAccess the display main menu
By briefly pressing and only when data pages are displayed:
lChange the favorite group to be displayed
By briefly pressing and only if there are several displays on
the network:
lChange the display to be controlled
Getting started
6 7” TFT display | Instruction manual v. 1.0 | © 2018 Continental Automotive Switzerland AG

Button Function
By pressing both buttons:
lLock/unlock Nav Control
Knob By rotating the knob:
lScroll the menu items and display pages
Briefly press:
lOpen a sub-menu
lConfirm the selection
Configure the display
Following are the steps for initial configuration:
1. When turned on, indicate the type of boat and number of engines.
2. Set up general device operations (see "General settings" on page18 and "System settings" on
page20).
3. Configure the sensors connected to Nav Box (see "Sensor configuration" on page29).
4. Change/remove data pages selecting the best layout and data to be viewed (see "Data page
configuration" on page12).
5. Enable/disable the alarms on the VDO CAN bus, NMEA 2000 and SAE J1939 networks (see "Alarm
management" on page24).
Getting started
77” TFT display | Instruction manual v. 1.0 | © 2018 Continental Automotive Switzerland AG

Data pages
What are data pages
Data pages display data received from the various sources. The pages are grouped into four favorites
groups, which can contain up to eleven pages each. Groups configuration is free, and a page can be
inserted into more than one group. In addition, the ALL VALUES group contains all the available data
pages, which vary according to the number of engines connected to Nav Box.
The default setting displays the four favorite groups with eleven pages each and the ALL VALUES group.
Possible operations
To scroll the pages, rotate the Nav Control knob or scroll your finger horizontally across the screen. To
change the favorite group, press on Nav Control or scroll your finger up and down on the screen. To
add/delete/edit pages, see "Data page configuration" on page12.
Shared features
Part Description
AID of the monitored engine and
parameter name
BData page content
CStatus bar with favorite group
and unit of measure
8 7” TFT display | Instruction manual v. 1.0 | © 2018 Continental Automotive Switzerland AG

Managed data
Information Unit of measure
Engine rpm rpm
Engine boost pressure bar, psi, kPa
Engine coolant temp °C, °F
Engine coolant pressure bar, psi, kPa
Engine oil temp °C, °F
Engine oil pressure bar, psi, kPa
Engine exhaust temp °C, °F
Engine hours h
Engine trim %
Gear oil temp °C, °F
Gear oil pressure bar, psi, kPa
Fuel %
True heading °
Course over ground °
App wind speed (AWS) m/s, km/h, kn, bft
App wind angle (AWA) °
True wind speed (TWS) m/s, km/h, kn, bft
True wind angle (TWA) °
True wind direction (TWD) °
Depth below transducer m, ft, fath
Data pages
97” TFT display | Instruction manual v. 1.0 | © 2018 Continental Automotive Switzerland AG

Information Unit of measure
Depth below keel m, ft, fath
Depth below waterline m, ft, fath
Tilt (Roll/Pitch) °
Speed over ground (SOG) km/h, mph, kn
Sumlog (STW) km/h, mph, kn
Avg speed through water km/h, mph, kn
Velocity made good km/h, mph, kn
Distance through water km, mi, nm
Trip through water km, mi, nm
Time h:m:s
Race timer h:m:s
Coordinates Degrees Minutes (DM)
Battery voltage V
Battery current A
Rudder angle °
Fresh water level %
Waste water level %
Sea water temp °C, °F
Ambient temp °C, °F
Barometer hPa, mmHg, inHg
True set angle °
Data pages
10 7” TFT display | Instruction manual v. 1.0 | © 2018 Continental Automotive Switzerland AG