VELOSSA TECH G70 User manual

2019-2021 Genesis G70 3.3T/2.0T
BIG MOUTH Ram Air Intake
Installation Guide

Please review this document before attempting installation.
You will need basic hand tools and 1-1.5 hours of installation time.
This product reuses the OEM hardware.
Kit Contents (Full Kit)
KIT CONTENTS Qty
AGS Simulator Bracket Assembly 1
#6, 1/2" screws 4
Diode Dynamics RGBW Controller 1
Diode Dynamics 1m LED Extension 1
Positive Cable w/ In-Line Fuse 1
Power Cable w/ Pigtail Connector 1
Switch 1
Switch Ground Cable w/ Crimped Connector 1
8" Zip ties 3
16" Zip ties 3
3/8" Conduit (3 feet) 1
Cable Clips 2
M6 Lock Nut 1
Assembled LIT KIT BIG MOUTH's 2

If you already own the GEN 4 Genesis G70 BIG MOUTH’s, skip ahead to slide 29
for wiring instructions
Kit Contents (LIT Flares Only)
KIT CONTENTS Qty
Diode Dynamics RGBW Controller 1
Diode Dynamics 1m LED Extension 1
Positive Cable w/ In-Line Fuse 1
Power Cable w/ Pigtail Connector 1
Switch 1
Switch Ground Cable w/ Crimped Connector 1
8" Zip ties 3
16" Zip ties 1
3/8" Conduit (3 feet) 1
Cable Clips 4
M6 Lock Nut 1
Assembled LIT Flares 2

Remove the shroud by pushing down on the center pin of the
pop-up clips and extracting them with a pry tool.
Shroud Removal

After removing the shroud, remove the top 4 screws (10mm) that
attach the bumper to the chassis
Bumper Removal

Remove the hidden screw (8mm) lying within the cavity identified below.
Bumper Removal

Remove all the indicated pop-up clips and screw from the
wheel well and bottom edge of the bumper
Bumper Removal

As the bumper gets pulled off, take notice of the indicated wiring harness connector.
To remove, pull back on the lever shown below. Once it swivels about entirely, pull to
disconnect.
Bumper Removal

The bolts holding both headlights must be removed for this install but do not
fully remove the headlight from its socket.
Remove using a 12mm socket
Headlight Removal

Swivel the headlights just enough to access the bolt hidden behind it
Moving Headlight

To remove the OEM inlets, there are 3 (10mm) screws that need to be
removed. You will need a 6” extension to reach the recessed screw indicated
with the blue arrow. Hold on to these, some of them will be reused.
Stock Snorkel Removal

Disconnect the indicated connector.
AGS Shroud Removal

AGS Shroud Removal
Disconnect the connector that is positioned in the highlighted area and remove the
bolt (10mm) to detach the metal mount. Put it aside, it will be installed again.

Detach the shroud by unfastening the 4 screws (10mm) marked below. You will need a
6” extension to reach the recessed screws marked by the arrows.
AGS Shroud Removal

AGS Shroud Removal
From the backside of the shroud, carefully undo the clips holding the wire loom by
pinching as shown in the image. There are numerous clips along the shroud.
Once these have been undone, the shroud should be free to remove.

Use channel locks on a wide setting to
pinch these clips, keep them pulled back
so they don’t snap back in place as you
move around the shroud.
Remove these Phillips screws
AGS Shroud Disassembly

Once the AGS system has been detached from
the car, you will need to remove the servo
motor located on the side of the AGS shroud.
Levers
Hold on to these
two screws
Once the motor is removed, you will see two AGS
levers. These levers will need to be removed so
they can be re-used in the AGS simulator bracket
in the coming slides.
AGS Servo Disassembly

Levers
AGS Servo Casing
Note these stock components for reference
AGS Simulator Housing Assembly

#6 screws
AGS Simulator Housing
OEM Screws from
previous slide
Back plate
These are the parts needed to fully assemble the AGS simulator. The AGS simulator
is necessary to prevent an engine code.
AGS Simulator Housing Assembly

DON’T TRY TO FORCE
THIS LEVER TO ROTATE
Idler lever is free
to move, but keep
it in this position
AGS Simulator Housing
(flipped)
Place levers back into motor casing.
IMPORTANT: THE RIGHT LEVER WILL NOT MOVE FREELY.
DO NOT ATTEMPT TO ROTATE.
AGS Simulator Housing Assembly