VentAHood EUROLINE User manual

Page 1
(Rev. 11/07)
L113
Read and Save These Instructions
All Hoods Must Be Installed By A Qualified Installer
INSTALLATION INSTRUCTIONS
EUROLINE/EUROLINE PRO
ISLAND RANGE HOOD
Read All Instructions Thoroughly Before Beginning Installation
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction. Switch power off at service panel
and lock the service disconnecting means to prevent power from
being switched on accidentally during installation.
B. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
C. Ducted fans must always be vented to the outdoors.
D. Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to
prevent back drafting. Follow the heating equipment
manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA), and
the American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and local code authorities.
WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCTWORK

Page 2
(Rev. 11/07)
L113
Ducting Do’s and Don’ts
NEVER restrict the duct size. The island dual blower unit (T200) requires 8” round duct or
equivalent (50 square inches). The island cluster blower unit (T400) requires 12” round or
equivalent (113 square inches). Using the included Vent-A-Hood transition will ensure proper
efficiency.
Do not use flexible or corrugated duct. This type of duct will restrict airflow and reduce
performance. Only use smooth, galvanized, metal duct. Observe local codes regarding special
duct requirements and placement of duct against combustibles. Make the duct run as short and
as straight as possible with as few turns as possible. Avoid sharp-angled turns. Instead, use
smooth, gradual turns such as adjustable elbows or 45 degree angled turns. For duct runs over
20 feet, increase the duct diameter by one inch for every ten feet of duct. A 90 degree elbow is
equal to 5 feet of duct. Using Vent-A-Hood roof jacks or wall louvers (back page) will ensure
proper efficiency. Airflow must not be restricted at the end of the duct run. Do not use screen
wire or spring-loaded doors on wall louvers or roof jacks. Do not terminate venting into an attic
or chimney. Where possible, seal joints with duct tape. The hood must be ducted to the outdoors
without restrictions.
Blower Duct Size Sq. Inch Area Vent-A-Hood Transition
Island Dual (T200) 8” round or equivalent 50” VP565 (Included)
Island Cluster Blower (T400) 12” round or equivalent 113” VP564 (Included)
YES
NO
Smooth Duct Smooth Gradual Turn
Flexible Duct Sharp Angled Turns

Page 3
(Rev. 11/07)
L113
Installation Details
1) Read all instructions thoroughly before beginning installation. Note: These instructions apply to standard hoods only.
Custom hoods may require additional specification consideration.
2) When installing an island range hood, it is recommended that the bottom edge of the hood be located no more than 30”
above the cooking surface. Exceeding recommended mounting height may compromise performance.
3) Load-bearing framework in the ceiling is necessary for the installation of an island hood. Additional framework
construction may be required. Do not attach an island hood to a structure that cannot support twice the weight of the
hood.
If applicable, remove the duct cover from its packaging and remove the hood-mounting screws from the base of the
duct cover. Install the duct cover to the load-bearing framework in the ceiling using appropriate hardware through the
four inside corner mounting flanges on the top of the duct cover.
4) Install the duct from the outside of the home down to the location of the exhaust outlet on the top of the transition plus
1”. This will allow the transition to engage 1” inside of the duct. Consult the connection diagrams (on next page) for
further details on exhaust outlet placement.
Use duct tape to seal all joints. A complete listing of available Vent-A-Hood ducting materials is listed on the back page
of this instruction sheet.
Transition heights are as follows:
Island Dual Blower (T200): 8” round duct connects to 9” tall VP565 transition (included).
Island Cluster Blower (T400): 12” round duct connects to 11 1/4” tall VP564 transition (included).
5) Prepare a protective surface on the floor or countertop for the hood. Remove the hood from its packaging and place it
upside-down on the protective surface for access to the inside of the hood.
Shown with duct cover installed (sold separately).

Page 4
(Rev. 11/07)
L113
Centerline
Of Hood
5" x 16"
Exhaust
Opening
8" Transition
Opening
Centerline
Of Hood
Vent Holes
Electrical 7 3/4"
7 3/4"
12"Transition
Opening 2 1/4"
AboveTop
of Hood
9"
16"
5"
8" Round 8" Round
18"
12" Round 12" Round
11 1/4"
8" Round 8" Round 8" Round
ledoM epyT stloV spmA zH MPR MFC "0.0@PS tnelaviuqE MFC MFC "1.0@PS MFC "2.0@PS MFC "3.0@PS dnuoRmuminiM eziStcuD erauqS sehcnI
lauD002T )2(eloPdedahS 511 4.3 06 0551 006 009 275 045 084 )tnelaviuqero("8 05
retsulC004T )4(eloPdedahS 511 8.6 06 0551 0021 0081 4411 0801 069 )tnelaviuqero("21 311
Installation Details Continued
6) Remove the blower shields (A) by loosening the two brass screws on the bottom of the shield. Gently close the back
draft dampers from the top side of the hood. To remove the blower housings, unsnap the suitcase latches (B) (one on
each side of the housing). The housings should be pulled forward and gently “tipped” to clear the blower wheels and
then out of the hood.
Warning: Make sure power is off and locked at the service disconnecting
means on the service panel during installation.
Connection Diagram (48”- 66” Widths)
Connection Diagram (36”- 48” Widths)
600 CFM T200 Dual Blower
(Top View)
1200 CFM T400 Dual Blowers
(Top View)
7) Remove the blower deck assembly by removing the 12 screws around the blower mounting plate. Unplug the electrical
connector(s) and set the blower assembly aside, taking care not to damage the blower wheels.
8) Install an appropriate 1/2” UL listed electrical wire clamp through the electrical strap(s) on top of the hood deck. Install
electrical wiring from the service panel to the hood location for each blower assembly. Consult the connection diagrams
(above) for further details on electrical placement. Support the hood beneath the location where it will hang and feed
the electrical wire(s) into the wire clamp(s). Tighten the wire clamp(s).
Transition Installed
(Side View)
VP565 Standard Transition
(Included)
VP564 Standard Transition
(Included)
Transition Installed
(Side View)
zNote: Add .5 amp for each halogen bulb. Equivalent CFM refers to the fact that the Magic Lung blower uses centrifugal filtration units, whereas others use
conventional filters. Apply this guideline when comparing blower units made by other manufacturers.

Page 5
(Rev. 11/07)
L113
Installation Details Continued
9) Raise the hood to its final position and attach it to the load-bearing framework in the ceiling using appropriate hardware
or to the duct cover using the screws previously removed in Step 3.
10) From inside the hood, using UL listed wire nuts, attach the “neutral” wire(s) to the white lead(s), the “hot”
wire(s) to the black lead(s), and the ground wire(s) to the green lead(s).
Warning: Do not operate hood without proper ground connection.
11) Attach the transition to the blower deck assembly and seal with duct tape. The transition must fit inside the exhaust
collar on the blower deck assembly. Reconnect the electrical connector(s). For assemblies with two connectors, connect
the right harness to the front connector and the left harness to the back connector. While taking care to properly align
the duct connection between the transition and the duct in the ceiling, reinstall the blower deck assembly into the
hood using the 12 screws previously removed in Step 7.
12) Replace the blower housings and the blower shields. Make sure that the dampers open and close smoothly.
13) Refer to Owner Maintenance Guide Operating Instructions for proper hood operation. Test all blower and light functions
to ensure they are operating properly.

Page 6
(Rev. 11/07)
L113
VENTING ACCESSORIES
6”,7”,8”
36”
VP500 6”
VP501 7”
VP502 8”
MODEL DIM
4 1/4”
3 1/4”
10”
3 1/4”
14”
BACK VENT ELBOW
VP559 3 1/4”X10”
MODEL DIM
10 TO 7 TRANSITION
7”
7 1/2”
10” 3 1/4”
MODEL DIM
VP521 3 1/4” x 10”- 7”
LOW PROFILE ROOF JACK
(MAXIMUM 4/12 PITCH)
16 3/4”
6 1/2”
16 3/4”
VP539 6”
VP540 7”
VP541 8”
MODEL DIM
VP552 10”
VP553 12”
MODEL DIM
LOW PROFILE ROOF JACK
(MAXIMUM 4/12 PITCH)
20 3/4”
10 1/2”
22 1/2”
MULTI-BLOWER TRANSITION
10” RD
12” RD
17 1/2” VP562
16 1/2” VP563
8”RD (VP562) 6”RD (VP562)
VP562 10”
VP563 12”
MODEL DIM
8”RD (VP563)
“Y” TRANSITION
18”
10”,12”
VP517 8” x 8” - 12”
VP518 6” x 8” - 12”
VP551 6” x 8” - 10”
MODEL DIM
2” FLANGE
10”
3 1/4”
MODEL DIM
WALL LOUVER
VP560 3 1/4”x10”
WALL LOUVER
11/2” FLANGE
8 5/8”
6”,7”,8”
VP526 6” RD
VP527 7” RD
VP528 8” RD
VP538 6”x8 1/2”
WALL LOUVER
11/2” FLANGE
11”
11”
VP554 10” RD
MODEL DIM
WALL LOUVER
11/2” FLANGE
13”
13”
VP555 12” RD
MODEL DIM
ADJUSTABLE ELBOW
6”,7”,8” ROUND
VP513 6”
VP514 7”
VP515 8”
MODEL DIM
11” 16”
11”
10”
3 1/4”
6”
VP550 6”-3 1/4”x10”
MODEL DIM
VP561 8”- 6” x 8 1/2”
MODEL DIM
6”
10 1/2”
7”
16”
11”
MODEL DIM
6”
24” 8 1/2”
MODEL DIM
3 1/4”
VP504 3 1/4” x 10”
VP505 3 1/4” x 12”
VP506 3 1/4” x 16”
30”
10”
12”
16”
MODEL DIM
8” RD (VP563)
VP529 6” TO 7”
8”
ROUND
8 1/2”
16”
12”
6”
8”
9”
5”
16”
VP565
MODEL
11 1/4”
18 1/2”
8”RD
12”
8”RD
8”
12”
5”
16”
MODEL DIM
SIDE VENT TRANSITION L & R
FOR ISLAND HOODS
8”
19”
16” 5”
VP544 LEFT SIDE
VP545 RIGHT SIDE
MODEL DIM
ROUND COLLAR
6”,8”
2” MORE
THAN HOLE
DIA.
2”MORETHAN
HOLE DIA.
MODEL DIM
OFFSET L & R TRANSITION
FOR ISLAND BLOWERS
COLLAR, SQUARE
6”
9”
11 1/2”
8 1/2”
VP537 6 x 8 1/2”
MODEL DIM
VP507 6” x 8 1/2”
6” RECTANGLE DUCT
3 1/4” RECTANGLE DUCT
ROUND DUCT
OFFSET KIT-ROUND OFFSET KIT-RECTANGLE STANDARD ISLAND
TRANSITION CLUSTER BLOWER TRANSITION
VP542 TOP LEFT ISLAND
VP543 TOP RIGHT ISLAND
VP533 6”
VP535 8”
BACK/SIDE VENT
ELBOW
MODEL
MODEL DIM
VP564