Verilux EasyFlex Deluxe VF02 User manual

VF02

2
Dear Customer,
Thank you for purchasing the Verilux EasyFlex® Deluxe
Natural Spectrum® Floor Lamp. You have received
a quality product, backed by a one year limited
warranty. As a Verilux customer, your satisfaction
means everything to us. We look forward to serving
you now and in the future.
Many other healthy lighting products are available
through our
catalog and online. Visit us on the web at
www.verilux.com to request a free catalog and learn
more about all our quality Verilux products, or call our
toll-free number 1-800-454-4408.
Have a Bright Day!
Nicholas Harmon
President, Verilux, Inc.

3
SAVE THESE INSTRUCTIONS
Thank you for purchasing the Original Natural Spectrum® Floor Lamp.
Please read the following safety information before using. To reduce the
risk of fire, electrical shock or injury to persons:
• Do NOT dismantle.
• Do NOT alter power cord.
• Turn off/unplug and allow to cool before replacing bulb or cleaning.
Important Safety Instructions
Warnings and Precautions
• For indoor use only.
• The lamp is an electrical device. DO NOT USE NEAR WATER.
• Before plugging in the lamp, check to make sure the voltage of the
wall socket does not exceed 120 volts.
• Not for use with light dimmers, timers, motion detectors or
extension cords.
• This product may cause interference with radios, cordless
telephones or devices that use a wireless remote control, such as
televisions. If interference occurs, move the product away from the
device, plug the product or device into a different outlet or move the
lamp out of the line of sight of the remote control receiver.
• Unplug from electrical outlet for extended periods of non-use or
during lightning storms to ensure protection of the electronics.
• WARNING: Do NOT use lubricating agent in assembly; please see
troubleshooting section if you are having difficulty assembling your
lamp.
• WARNING: Do not use the lamp outside or in wet locations such as
bathrooms. It is intended for indoor, dry use only.
• WARNING: This product contains Mercury in the bulb. Dispose of
bulb per local regulations.

4
Avertissements et Précautions
• Pour usage intérieur seulement.
• La lampe est un dispositif électrique. NE PAS UTILISER PRÈS DE
L’EAU.
• Avant de brancher la lampe, vérifier que la tension de la prise
murale ne dépasse pas 120 volts.
• Ne pas utiliser avec des gradateurs de lumière, des minuteries, des
détecteurs de mouvement ou des rallonges.
• Ce produit peut causer des interférences avec des radios, des
téléphones sans fil ou des appareils utilisant une télécommande
sans fil, telle qu’une télévision.
• Si des interférences se produisent, éloigner le produit de l’appareil,
brancher le produit ou l’appareil dans une autre prise ou encore
déplacer la lampe hors de la ligne de visée du détecteur de
télécommande.
• Débrancher de la prise électrique lorsque le produit ne sert pas
pendant de longues périodes ou lors d’orages électriques afin
d’assurer la protection des pièces électroniques.
• AVERTISSEMENT : Ne PAS utiliser de produit lubrifiant lors de
l’assemblage; voir la section de dépannage en cas de difficulté lors
de l’assemblage de la lampe.
• AVERTISSEMENT : Ne pas utiliser la lampe à l’extérieur ou dans
des endroits humides, telle qu’une salle de bain. La lampe doit être
uniquement utilisée à l’intérieur et dans un endroit sec.
• AVERTISSEMENT : Ce produit contient du mercure dans son
ampoule. Suivre les règlements locaux pour la mise au rebut de
l’ampoule.

5
Getting Started
Main Parts & Controls
A. Ergonomic Handle
B. Lamp Head
C. High/Off/Low Switch
D. Gooseneck
E. Shaft
F. Ergonomic Height
Adjustment Lever
G. Lamp Base
H. Power Cord
I. Ballast
J. LED Indicator
K. Bulb
L. Parabolic Light Diffuser
A
BC
D
E
F
H
G
I
Close-up of Lamp Head
Close-up of Ballast J
K
L
CAUTION:
DO NOT LIFT THE LAMP BY THE
GOOSENECK. THE LAMP SHOULD BE
LIFTED BY THE SHAFT.
MISE EN GARDE :
NE PAS SOULEVER LA LAMPE PAR SON
COL-DE-CYGNE. LA LAMPE DOIT ÊTRE
SOULEVÉE PAR LA TIGE.

6
Getting Started — continued
Please Read Instructions Carefully Before Using the EasyFlex®.
1. Unpack lamp carefully, removing all packaging material, and confirm
you have all parts shown in the diagram. For your convenience, the
bulb has been inserted into the socket.
2. Remove all pieces from box. Locate the two screws and tightening
tool in the plastic bag and set aside.
3. Detach the red plastic protective pieces and store them in the event
you need to return the lamp.
4. The clear plastic sleeve on the shaft is specially designed to
tear away easily. To avoid scratching the metal shaft, do not
use a sharp object to cut the plastic.
IMPORTANT NOTE: Remove red plastic protective pieces prior to
assembly.

7
Assembly Instructions
1. Set the lamp base on the floor and insert
the lamp shaft over the base support unit
until the screw holes line up as shown in
Fig. 1. Insert the screw using the tightening
tool and turn clockwise to tighten.
2. Hold the upper shaft with one hand
and release the ergonomic height
adjustment lever by gently pulling it
upward as shown in Fig. 2. Extend
the upper shaft approximately
12". Lock the adjustment lever by
gently pushing it downward. Once
assembly instructions are complete,
raise or lower the upper shaft to
the desired height by releasing and
locking the height adjustment lever.
Close-up of screw hole in
the lamp base
Fig. 1
Fig. 2

8
Assembly Instructions — continued
3. Attach the lamp head gooseneck to the
shaft until the screw holes line up as
shown in Fig. 3. Use care when tucking
the wire into the shaft. Form a loop with
any excess wire prior to tucking it. Insert
the screw using the tightening tool and
turn clockwise to tighten.
4. Remove the light diffuser from
the protective plastic bag.
Insert the plastic pegs at the
bottom of the light diffuser into
the openings near the bulb
socket. Snap the tab
into place as shown
in Fig. 4.
Note: Be sure all
styrofoam packing
is removed from the bulb
area prior to installing the
light diffuser.
Close-up of screw hole in
the lamp head
Fig. 3
Fig. 4

9
Assembly Instructions — continued
5. Attach the ballast to the power
cord. Use care to align the 4-pin
plug properly. DO NOT FORCE.
The power cord is designed to
connect only one way (Fig. 5).
6. Plug the ballast into a standard 120V
50/60Hz outlet and turn the lamp on. The
green LED indicator (J) on center of the
ballast will illuminate (Fig. 6). If not, please
refer to the troubleshooting section of this
manual (see page 11).
Note: Green LED indicator will not illuminate if
lamp is turned off or bulb is removed.
J
ATTENTION!
Fig. 5
Fig. 6
ALWAYS lift your
lamp by the shaft DO NOT lift the lamp by the gooseneck
WARNING: Do not block vents on the
ballast. Vents are necessary for proper
function of the ballast; blocking them
may cause overheating of the ballast and
increase the risk of fire.
AVERTISSEMENT : Ne pas bloquer les ouvertures sur le
ballast. Vents sont nécessaires pour le bon fonctionnement
du ballast, le blocage entre eux peuvent provoquer une
surchauffe du ballast et d’accroître le risque d'incendie.

10
Bulb Replacement
Fig. 7
Correctly Seated Bulb Incorrectly Seated Bulb
No Gap Notice
Large
Gap
Fig. 8
B
D
C
A
Fig. 9
Removal
1. Unplug the lamp from the power source.
2. To access the bulb, remove light diffuser
by depressing the tab and lifting it out
(Fig. 7).
3. Firmly hold the bulb base (B) and pull
bulb (C) from the socket (A) in an outward
motion (Fig. 8).
Installation
1. Unplug the lamp from the power source.
2. Firmly hold the base (B) and push bulb (C)
into the socket (A).
3. Be sure the bulb is firmly seated in the
socket (Fig. 9) and snapped into the
metal bulb clip (D).
4. Replace the light diffuser.
Attention: Do not grip the bulb by the
glass tubes. Only touch the base when
removing or inserting the bulb.

11
Troubleshooting
Before requesting service on your Verilux® lamp, please read the
following:
• Make sure all power connectors, cords and plugs are inserted fully
and securely.
• Be sure the bulb is securely seated into the socket (see page 9).
• Make sure there is power to the wall outlet or try another outlet.
• CAUTION: DISCONNECT LAMP BEFORE PERFORMING
ALIGNMENT ACTIVITY. MISE EN GARDE : DÉBRANCHER LA
LAMPE AVANT D’EFFECTUER SON ALIGNEMENT. Correct
alignment with screw holes can be accomplished by following these
steps:
1. Always start with the base and work your way up the shaft and
attach the head last.
2. Place your foot on the base of the lamp on the floor.
3. While holding the shaft with your hand, gently rock the unit back
and forth.
4. Shaft should ease into socket and screw holes will align.

12
Troubleshooting – continued
Be sure the bulb is securely seated into the socket, repeat the bulb
installation process. CAUTION: DISCONNECT LAMP FROM OUTLET
PRIOR TO REPEATING THE BULB INSTALLATION PROCESS. MISE EN
GARDE : DÉBRANCHER LA LAMPE DE LA PRISE DE COURANT AVANT
DE POSER UNE NOUVELLE AMPOULE.
WARNING: Do not block vents on ballast. Vents are necessary
for proper function of the ballast; blocking them may cause
overheating of the ballast and increase risk of fire.
AVERTISSEMENT : Ne pas bloquer les ouvertures sur le
ballast. Vents sont nécessaires pour le bon fonctionnement du
ballast, le blocage entre eux peuvent provoquer une surchauffe
du ballast et d’accroître le risque d'incendie.

13
Care & Cleaning
Your lamp is made from high quality materials that will last for many
years with minimum care. You may want to periodically clean the lamp,
using a mild non-abrasive cleaner and soft cloth. When cleaning, make
sure you have turned off and unplugged the unit, and allowed sufficient
time for the unit to cool. All liquid should be properly wiped away and
dried prior to restoring power.
CAUTION: DO NOT USE SOLVENTS OR CLEANERS CONTAINING
ABRASIVES, OR AMMONIA BASED CLEANERS.
MISE EN GARDE : NE PAS UTILISER DE SOLVANTS NI DE
NETTOYANTS CONTENANT DES ABRASIFS OU DE L’AMMONIAQUE.
WARNING: All moisture should be properly wiped away and dried prior
to restoring power.
AVERTISSEMENT : Toute humidité doit être essuyée et séchée avant
de remettre la lampe sous tension.

Please visit our website at www.verilux.com or call our Customer Service Department at
1-800-786-6850
Representatives are available Monday — Friday, 9am — 5pm EST
340 Mad River Park, Waitsfield, VT 05673
One Year Limited Warranty
ATTENTION! ONCE OPENED, PLEASE DO NOT RETURN THIS PRODUCT TO THE
STORE WHERE IT WAS PURCHASED FOR REPAIR OR REPLACEMENT!
Many questions may be answered by visiting www.verilux.com, or you may call our
Customer Service Department at 800-786-6850 during normal business hours.
This limited warranty is provided by: Verilux, Inc., 340 Mad River Park, Waitsfield, VT 05673
Verilux warrants this product to be free from defects in material and workmanship for a
period of one year from the date of the original retail purchase from Verilux or an authorized
Verilux distributor. Proof of purchase is required for all warranty claims. During the
limited warranty period, Verilux, Inc. will, at its option, repair or replace defective parts of
this product, at no charge to the customer, subject to the following limitations: This limited
warranty does not include any postage, freight, handling, insurance or delivery fees. This
warranty does not cover damage, defect or failure caused by or resulting from accident,
external destruction, alteration, modification, abuse, misuse or misapplication of this
product.
This warranty does not cover damage to the product resulting from return shipping or
handling. The use of shipping insurance is recommended to help protect your product.
Return Authorization is required for all returns. To obtain a Return Authorization, please
contact the Verilux Customer Service Department at 800-786-6850.
If, during the first year of ownership, this product fails to operate properly, it should be
returned as specified at www.verilux.com/warrantyreplacement or as instructed by a Verilux
customer service representative at 800-786-6850.
Note: Verilux recommends using a quality surge suppressor on all electronics equipment.
Voltage variations and spikes can damage electronic components in any system. A quality
suppressor can eliminate the vast majority of failures attributed to surges and may be
purchased at electronics stores.
Due to ongoing improvements, actual product may have slight variations from the product described in this manual.

VF02-MAN-Rev5
Printed in China for Verilux, Inc.
© Copyright 2011 Verilux, Inc. All rights reserved.