VEVOR XRJF-11 Specification sheet

COMMERCIAL SLUSH MACHINE SERIES
PRODUCT INSTRUCTION MANUAL

01
COMMERCIAL SLUSH MACHINE SERIES
PRODUCT INSTRUCTION MANUAL
NEED HELP? CONTACTUS!
Have product questions? Need technical suppo? Please feel free to contact us:
CustomerSe[email protected]
This is the original instruction,Please read all manual instructions carefully before operating.
VEVOR resees clear interpretation of our user manual. The appearance of the product shall be subject to
the product you received. Please forgive us that we won't inform you again if there is any technology or
software updates on our product.
XRJF-11

02
Content
1. Safety Instructions .................................................................................................................................................................03
2. Installation Instructions for The Whole Machine........................................................................................................06
3. Names of Each Pa.................................................................................................................................................................07
4. Product Specications...........................................................................................................................................................08
5. Operating Instructions...........................................................................................................................................................08
6. Out-of-Material Alarm Function........................................................................................................................................10
7. Slush Production.......................................................................................................................................................................11
8. Simple Cleaning.........................................................................................................................................................................12
9. Cleaning & Maintenance........................................................................................................................................................12
10. Cleaning Method of Pas...................................................................................................................................................13
11. The Assembly Method of The Component..................................................................................................................14
12. Methods for Installing on The Machine.........................................................................................................................14
13. Troubleshooting Instructions............................................................................................................................................17
14. Circuit Diagram.......................................................................................................................................................................19
15. Environmental List.................................................................................................................................................................20

03
Safety Instructions
Dear user,
Hello! Thank you for using our products, in order for you to better read this manual and use this
product, and to prevent personal inju and object damage accidents, please be sure to read carefully
and comply with the following symbols in this manual.
Be sure to store this book in a location where users can access it at any time
Behavior or action
that must be
prohibited
If the operation is
wrong, it may cause
harm to the user
The behavior or
action that must be
followed
If the operation is
wrong, it may cause
damage to goods
and propey
Electrical Requirements
It is necessa to use a separate dedicated socket and reliably grounded, and the power cord of
this series of slushy machines is equipped with a three-wire (grounded) plug which should be
used.Conforms to standard three-wire (grounded) sockets. Never remove the third pin (ground)
of the power cord under any circumstances.
The power cord plug should remain in rm contact with the outlet, otherwise it may cause a
re.In order to prevent damage to the power cord, do not let the slushy mahine press the
power cord or aicially step on the power cord, when moving the slushy machine, please be
careful and cautious, do not roll the power cord, otherwise the right side of the power supply
software can be damaged, causing electric shock or re accidents.
Be sure to use the power supply specied on the nameplate of this slushy machine; if the volt-
age uctuation range is large, please install an automatic voltage regulator suitable for power
according to the nameplate parameters.
Do not pull the plug of the slushy machine by pulling the power cord, hold the plug tightly and
pull it directly from the socket.
Before cleaning, repairing and replacing damaged lighting equipment, the power plug of the
slushy machine must be unplugged to prevent electric shock.
Do not use the power cord if it is damaged or the plug is worn, and it must be replaced at the
maintenance point designated by the manufacturer.

When there is a leakage of ammable gases such as gas, the valve of the gas leakage should be
closed immediately, and then the doors and windows should be opened, and the plug of elec-
trical devices such as the slushy machines should not be unplugged or plugged.
Please install a leakage o circuit protector before use to ensure personal safety and safe use of
the product.
Usage
Do not put your nger in the feeder of the pot, otherwise it may cause nger inju or machine
failure.
Before disassembling and cleaning the discharge valve and agitator, the power supply must be
turned o, otherwise it may cause personal inju.
It is strictly forbidden to disassemble and transform the slushy machine, and it is forbidden to
aicially damage the refrigeration pipeline. Repairs of the slushy machines must be carried
out by qualied personnel.
In the event of an abnormality or failure, please unplug the power supply, and stop using it, and
if you need repairs, you must contact the designated maintenance point.
When the slushy machine is not used for a long time, please unplug the power plug, otherwise
the aging of the insulation layer will cause a leakage re.
No trial operation shall be carried out without the guidance of a professional, otherwise it may
cause the failure of the machine and safety accidents.
Do not spray with water to, rinse the slushy machine, and do not place the slushy machine in a
wet place that is easy to splash water, so as not to aect the electrical insulation peormance
of the slushy machine. It may even lead to accidents such as electric shock and re.
Please pay attention to the care of children, prevent children from sticking their hands, feet, etc.
into the slushy machine compament, back and other gold layer protective pas of the punch-
ing holes, edge seams, so as not to cause harm to the body.
When the slushy machine is not in use, please close the door of the slushy machine and do not
let children play.
This appliance contains ammable materials that must be disposed of and recycled by qualied
personnel and institutions when discarded.
04

This appliance contains combustible blowing agent, beware of re, (the product has the mark
of "beware of re"). When there is an abnormality in the product, it must be repaired by relevant
qualied personnel and institutions.
This machine is not intended for use by persons with frailty, children, retardation, or mental
disorders, except under the guidance or assistance of a person responsible for safety.
Children should be supeised to ensure that children do not play with machines.
If the power cord is damaged, it must be repaired by a professional.
In the vicinity of slushy machine, do not store or use gasoline and other ammable items to
avoid causing a re.
Explosives, such as combustion sprays, shall not be stored in utensils.
Usage Environment
Avoid placing slushy machine in wet areas, such as near faucet attachments or sinks.
This series of slushy machine is not suitable for outdoor use. Normal operating ambient tem-
perature is 3° C-32° C/37.4° F-89.6° F. The normal working water temperature is 0.6 ° C-32℃
/33.08°F-89.6°F。
Do not use in places with a lot of sulfuric acid components such as hot springs, or in places with
a lot of salt near bays. Otherwise, it may cause corrosion inside the machine and cause machine
failure.
Avoid direct sunlight, if the slushy machine is installed in direct sunlight, it may cause abnormal
operation and may shoen the working life of the slushy machine.
Away from the heat source, the slushy machine should not be installed near the stove, oven or
other equipment that generates high temperatures, and t to avoid direct sunlight so as not to
aect the heat dissipation of the machine.
The slushy machine needs to be placed on a at and solid ground and withdraw from the pack-
aging base, and if it is necessa to raise it, it is also necessa to choose a smooth, hard,
non-burning counteop, otherwise it may cause dumping, noise, and excessive vibration.
Slushy machine should not be placed in places that are wet or susceptible to splashing water,
otherwise they will cause res or electric shock.
This appliance is used for similar purposes: e.g. in the kitchen area of a shop, oce or
other workplaces; Customers of farms and hotels, motels and residential environments;
Family hotel environment; Restaurants and similar non-retail applications.
NOTICE
05

Installation of Slushy Machine
When moving, the box should be kept as straight as possible, and the maximum tilt
should not exceed 45°. When moving, please ensure that there are at least two or more
people, and avoid upside down and horizontal placement.
The maximum stack cannot exceed 2 layers.
06
Installation Instructions for The Whole Machine
Installation of the Power Supply
1．The power supply connected should be the same as the one indicated on the nameplate of the
machine.
2．Do not connect other electrical appliances to the same outlet.
3．Y-type connection, must be replaced by the manufacturer, seice agencies or qualied personnel
to connect the power cord.
4．The power plug should be plugged directly into a power outlet with a ground wire, not into a
tempora terminal block. All wiring must comply with national or regional standards.
5. Voltage uctuations shall not exceed ±10% of the rated voltage, otherwise a voltage regulator shall
be installed.
1. Remove all packaging components.
2. Check if the machine is damaged during transpoation, and then remove the attachments.
3. This series of slushy machine should be placed in a clean place with air circulation, not suitable for
open air, not suitable for direct sunlight and rain, nor can it be placed near the heat source.
4. The ambient temperature around the series of machines should not be less than 3 °C/37.4°F, not
higher than 38 °C/100.4°F, and the appropriate spacing should be retained around the four sides to
maximize the eciency of the slushy machine and the heat dissipation of the machine.
5. When the slushy machine is installed, please place the slushy machine horizontally, and items
cannot be placed on the top.

1. Do not place items on the top cover of this machine, otherwise it will cause noise.
2. The left, right and rear sides of the machine must have sucient heat dissipation space, otherwise
it will aect the heat dissipation, and the production capacity of the machine aected by the
air-cooled circulation channel, and it is forbidden to place items around.
3. The slushy machine should be kept away from the heat source, it is strictly forbidden to use it in a
high or low temperature environment, and the direct sunlight should be avoided as much as possible
so as not to aect the heat dissipation of the machine.
4. Sterilization should be carried out daily. Otherwise, bacterial multiplication can be detrimental to
health.
5. If the slushy machine is placed for a long time, please disassemble and wash it, turn o the power
plug, please carefully d the water of the material tank and the freezing tank; after they are dried
and then covered with the material basin cover for safekeeping.
Proper Operation When Using
07
Names of Each Pa
Pre-boot Inspection
1. Is the slushy machine placed horizontally?
2. Is there any problem with the power outlet?
3. Whether the access to the power supply is consistent with the one marked on the machine
nameplate.
Material basin cover
Level oat
Material cylinder
Display screen
Tie rod holder
Tie rod
Freezer cylinder
Magnetic light box
Power switch
Handle
Handle cross pin
Fasten nut
Discharge valve assembly
Stirrer assembly
Pick up the water box
Attach the lid of the water box
Water box hanging plate
Remaining Fee Mouth
Footwork
PNT0
PNT1

Discharge Valve Assembly Agitator Components
Stem
Stem O-ring
Discharge valve
Discharge valve cap
Outlet D-ring
Flared seals
Scraper
Stirrer
08
To prevent accidental movement, the button needs to be pressed slightly harder.
When switching between keys, press the Stop button rst, then switch.
For safety reasons, no buttons can be operated without an outlet valve installed.
Operating Instructions
Product Specications
Model
Refrigerating Capacity
Climate Type
Refrigerating
Input Power
Rated Voltage
Foam Material
Net Weight
Dimensions
XRJF-11
15-25L/H
N/SN
R410/380g
1550W
AC120V 60Hz
Cyclopentane
54KG
635*290*860mm

It is normal for the current temperature of the freezer tank to deviate from the actual temperature of
the raw material in the cylinder. The freezer temperature is not involved in forming control when
making snow melt.
Instructions: Press "Stop", "Clean", "Slush", "Cold Drink" on the touch screen to
enter the corresponding working mode.
On the password input inteace, click the password input area and enter the password "666666" and
then click "OK" to enter the parameter setting inteace.
Password Input Inteace
09
Setting key
Slush gear
Number of cups
The current
voltage
The current
tempera-
ture of the
freezer tank
Current speed
Clean key
Slush Key Cold Drink key Stop key The current forming scale
Password input area Return key
Delete the key
Conrmation key

10
Parameter Setting Inteace
Slush gear: 1-8 gears can be adjusted according to "plus" or "minus" gear adjustment, The default is 3
gears, the higher the gear, the harder the smoothie is, and the lower the gear, the softer the smoothie
is.
Slush cycle time: This time is adjusted for the refrigeration system after 100% slush molding Stop
time, 5-20 minutes can be adjusted according to "plus" or "minus" for gear adjustment The default is
10 minutes.
Preseation temperature: set the pan preseation temperature, 5 °C-15 °C adjustable, the default is
10 °C.
Cold drink temperature: Set the cold drink refrigeration shutdown temperature, 2 °C -10 °C can be
adjusted, the default is 7 °C.
Number of cups: Record the number of discharged cups for machine slush and cold drinks, and clear
the data by "clearing" minus.
Facto reset: All the data set by the user is cleared and restored to the parameters set by the facto
settings.
Next: Go to System 2 (Right Cylinder System) User Settings.
Note: All user setting parameters are equipped with power-o saving function, and the settings are
automatically saved after returning.
Out-of-Material Alarm Function
The bottom of the tank is equipped with a level
oat, any one of the tank level oats at a low level,
repo a lack of materials, add raw materials to the
tank level oat to oat, and the lack of material
alarm is closed.
Level oat

11
Slush Production
1.Raw Material Preparation
According to the manufacturer's operating instructions, dilute the concen-
trate with water and stir in a suitable container. The mixture contains sugars ,
the amount of which should be kept between 13%-18%. Lower and higher
concentrations can be destroyed agitators and stirring motors.
2.Raw Material Filling
Before adding the raw materials, t to ensure that there is no residual moisture
in the freezing tank during cleaning. Check the discharge valve assembly,
whether it is installed in place, and whether the four fastening nuts are twisted.
Inject about 6 liters of slush raw material into the material tank,
(The single-tank slushy machine can pour up to about 10 liters of raw material
into the material tank.)
materials
3.Sta The Machine
Refer to the operating instructions
Note: When the machine is in working condition, do
not put your ngers into the feed bowl raw material
supply po. Failure to do so may result in nger inju-
ries or machine malfunction.
switch operation panel
4.Make Smoothies
When the shape ratio reaches 99% and the machine is
automatically stopped, it means that the smoothie is
ready. Simply pull the handle down to punch out the
smoothie.
close
open
cup

12
Be sure to unplug and turn o the power supply before cleaning.
Before any cleaning or maintenance, be sure to bring protective equipment (glue hands sleeves, pro-
tective glasses, etc.), which ensure your safety.
Please do not rinse the slush with water spray, so as not to aect the insulation peormance of the
electrical appliances, caused leakage hazard.
Do not use hard bristle brushes, wire brushes, nor detergent powders, gasoline, or bananas, water,
acetone and other organic solvents, boiling water or acids, alkalis, etc. to clean the slushy machine;
improper use will cause damage to the slushy machine material and aect the seice life.
When cleaning a location with warning signs, be careful not to scratch your hands.
Wash with disinfectant that meets food hygiene requirements.
Use a suitable food-grade neutral cleaning agent to avoid damaging pas.
The following items can damage the suace of the slush.
Cleaning & Maintenance
Alkaline or
weakly alkaline
Kitchen cleaner Gasoline, thinner,
alcohol, acid, petroleum
Boiling water
Brush
1.Release all the ingredients
2.Power o the machine
3.Fill the material tank with an appropriate amount of food
detergent to prepare hot water that does not exceed 50 ° C,
then open the tank cover and pour the hot water into the
tank.
4.Turn on the power of the machine, then press the wash
button and let the agitator stir for 2-3 minutes.
5.Release all the water from the tank, and then repeat the
operation more than 2-4 times.
6.Turn o stirring and power.
Simple Cleaning
NOTICE
Note: Please pour clean water into the corresponding
basin to be cleaned, do not exceed the highest marking
line on the tank, if you want to clean the machine thor-
oughly, please turn o the machine power.
close
open
bucket

13
Cleaning Method of Pas
User Considerations
Do not damage or lose components during operation.
Do not wash resin pas with hot water or a dishwashing machine. Failure to do so may cause
deformation.
Do not soak pas in detergents or germicidal solutions for more than 30 minutes. Failure to do so may
cause deterioration.
For some areas that are prone to accumulation of residual material, please wash carefully with a
cleaning brush.
Some pas have pointed edges, be careful not to scratch your hands.
Carefully wash the agitator with a washing brush, including the middle pa.
Hopper cover
Valve pole
O seals for valve pole
Handle
Handle xing pin
Suppoing outlet valve
Fasten screws
Drip tray
Cover of Drip tray
Spout seals D
Outlet valve cap
Beater scraper
Beater
Sealant seals
Use food detergent and cleaning brushes to clean all pas that have been disassembled
When using it for the rst time or not using it for a long time, please clean the
pas before use.

14
Assembly of The Valve Stem
Assembly of Agitator Components
Assembly of Discharge Valves
1.Install the O-ring on the valve stem and assemble it
according to the diagram.
2.After the O-ring is installed, the suace is greased.
Valve pole
O seals for valve pole
1.The ared sealing ring is lubricated
at both ends.
2.Install the ared seal directly behind
the agitator.
3.Mount the scraper on the agitator. The spatula
arrangement in the agitator is loose.
Beater scraper
Beater
Sealant seals
1.Inse the greased stem of the installed
O-ring into the outlet hole of the discharge head.
2.Install the D-ring on the discharge head
mounting slot.
Valve pole
Suppoing outlet valve Spout seals D
The Assembly Method of The Component
Methods for Installing on The Machine
When assembling and disassembling pas, turn o the control power switch.
Otherwise, it is possible to accidentally touch the staing machine and cause
injuries to the person.
Disinfect your hands and ngers during operation. Otherwise, it may endanger
human health.

15
Mounting of The Handle
Inse the handle socket into the lever pin, then inse the
handle pin into the lever holder, and then align the handle
pin hole with the vel pin, and then the vel pin goes directly
through the handle pin hole.
Handle
Handle xing pin
Tie rod holder
Tie rod pin
Installation of Agitators
It is impoant to ensure that the control power switch is
turned o. Conrm that the display is o. Inse the agita-
tor into the freezer tank and slowly rotate the agitator with
your hands to embed the quad head of the reducer into the
quad connector of the reducer.
Freezing cylinder
Agitator assembly
Installation of Discharge Manifolds
The four mounting holes of the discharge valve are passed
through the four discharge heads to x the bolts, the stem
head is stuck into the lever clamp position, and then the
four fastening nuts are evenly fastened diagonally.
Drip tray
Water box hanging board
Cover of Drip tray
Installation of Discharge Manifolds
Pull rod
Fastening screws
Outlet valve assembly
Fasten screws
The four mounting holes of the discharge
valve are passed through the four discharge
heads to x the bolts, the stem head is stuck
into the lever clamp position, and then the
four fastening nuts are evenly fastened
diagonally.

16
Be sure to unplug the power supply and turn o the water source before cleaning. Do not plug the
power supply with wet hands, or there will be a risk of electric shock.
Wipe the suace of the slushy machine shell by using a soft towel or sponge dipped in warm water
(a diluted neutral detergent is available).
After washing with detergent, wipe it o promptly with a soft cloth or sponge dipped in water.
Wipe the water o the suace of the enclosure with a d cloth.
Please never spill water directly on the machine. Failure to do so may result in a power leakage or
accident.
Check once or twice a month to conrm whether the power cord is damaged.
Cleaning And Maintenance of The Enclosure
Even if there are scars on the sealing ring that cannot be seen with the naked eye, it may cause prob-
lems such as "slush leakage", so please replace the new product regularly with a rough replacement
period of three months. Even within the replacement period, if there is a problem such as scars, please
replace it in time.
Consumable Pas
O seals for valve pole Spout seals DSealant seals
After working for a period of time, the condenser
will be dusty and aect the heat dissipation, and
the cooling eect will become worse
(Manifested as: the output of the slush decreases
or the slush is dicult to be formed), please clean
once eve three months (if the using environment
is poor, please clean once a month), be sure to ask a
professional cleaner to clean, turn o the power
before cleaning, and pay attention not to damage
condenser ns of the vessel.
Cleaning of The Condenser
Do not touch the condenser ns directly with your hands as this can cause inju.
When disassembling the right panel, pay attention to the display protection.
Display screen
condenser Right panel

17
Troubleshooting Instructions
The slushy machine you receive is a mechatronic professional equipment that integrates computer
program control, mechanical transmission and ecient refrigeration system! You must arrange for
your own personnel to be responsible for the operation and maintenance of this equipment, at the
same time, please understand the installation and maintenance requirements of this equipment in
detail when purchasing the machine, and receive professional training before use!!! (Ve impoant)
For the violation of the installation, use and maintenance requirements of the machine caused by
equipment failure, is not within the scope of the company's warranty!
At the same time, for the problems encountered in the process of use, please strictly follow the
following precautions:
Serial
number Cause Analysis Processing method
Is the power switch of the equipment
energized Check the power supply, plugs and
sockets
The internal wires of the machine are
chewed or loosened by rats Hire a professional electrician to replace or x
The computer board of the equipment
fails Call the company's phone number to be
handled by the company's professional sta
Insucient input power line or
switch load Hire your own professional electrician for
replacement
The internal circuit of the equipment is
chewed or broken by rats Hire a professional electrician to replace or wrap
Excessive load on equipment due to high
gear setting Downward gear adjustment
Sho circuit inside the motor, circuit
board or compressor Call the company's phone number to be handled by the company's professional sta
The machine case has inductive
electricity
Check whether the power inlet line is
reliably grounded, no grounding wire; if it is
worn, you need to replace it with a new one
D-seal is not installed properly Check whether the two D-rings of the
outlet valve are installed in the slot
Broken O-ring of beating rod Take down the beating rod to check whether the seal at both ends is worn,
there is wear need to replace the new
Fastening screws are not tightened Tighten the four screws evenly diagonally
Incorrect disassembly or installation
method of beating rod, resulting in
broken beating rod seal and leakage of
material or water
Gently pull out veically when
disassembling, and always apply medical
petroleum jelly as lubricant when installing,
apply it around the valve stem seal and
press down veically. Do not damage the
seal with sharp objects when cleaning.
The discharge head screw is not
tightened Tighten the four screws evenly diagonally
Worn seal at the back end of the agitator Replace rear end seal
The residual
material pipe
leaked material
and water
Leakage of water
and material on
or under the
discharge head
after staing the
machine
Power switch
tripped after
power on
No display after
power on
Feeling of
leakage after
power on
1
2
4
3
5

18
The machine is noisy when pressing the
cleaning key
The cleaning noise will gradually reduce
after adding raw materials
The machine is noisy when cooling
The ground on which the machine is placed
is not horizontal, adjust by yourself
Fan noise
The noise will be reduced gradually after
adding material when there is a lack of
material.
Motor noise
The gear setting is too high, adjust the gear
by yourself
Compressor noise
Abnormal noise
after power on
6
Self-check whether there are foreign
objects around the fan blades and whether
the xing screws of fan bracket are loose
Check whether the wind blade rubs the
nest shell when rotating
Check whether the xing screws of
condenser are loose
Noise generated by too high gear setting
Noise of the motor itself
The xing screws of motor are loose
Condenser has not been cleaned for a
long time, the condenser is too diy
resulting in excessive compressor load
Internal piping deformation causes
vibration noise
Compressor normal noise
7
Smoothie
discharges are
too soft or too
little
Too frequent discharge Wait until the molding ratio reaches 90% or
more before mixing the material
Poor heat dissipation Solve the problem of ventilation on both sides of the machine, leave at least one
meter of space on both sides
Not enough gears Adjusting gears
Machine cooling system failure Refrigerant leakage or compressor failure
8
No smoothie or
too soft after
stopping the
machine
The beating handle is not in place When the handle does not hit downward, the beater switch is not closed and the
machine does not sta
The rst cup is softer after stopping the
machine Sta after a long shutdown, it's normal for the rst cup to be softer
Gear setting too high or too low Proper gear adjustment
Downtime setting is too long Appropriate adjustment of downtime
Discharge micro switch failure Replacement of discharge micro switch
9Machine LL
Alarm
Sensing anomalies Check if there are magnets on the motor or
adjust the speed sensor position or replace
Long buzzer sound, the whole machine
stops working Check if the sensor is out of position or the connection wire is disconnected

19
Tank freezes Proper downward adjustment of gear
Motor does not rotate or motor idling
speed is slow Call the company's phone number to be handled by the company's professional sta
Slow motor speed Check if the motor is damaged
Machine 55
alarm
10
11
Call the company's phone number to be
handled by the company's professional sta
Sensor failure or loose sensor linkage
Proper downward adjustment of gearImproper gear selection
Poor cooling Check whether the condenser is diy and blocked, whether the exhaust air is smooth
and the refrigerant is less
The ring temperature is too high,
ventilation and heat dissipation is not
good or the air inlet and outlet are
blocked
Ensure that the equipment is in a ventilated
position and remove obstacles from the air
inlet and outlet
Unstable voltage or insucient power
supply capacity Ask a professional to handle it
Refrigeration evaporation cylinder frosts
badly or has no frost in the return air
pipe when empty Leakage of slush
Unable to
reach "99"
12 "UH" alarm High voltage alarm Adjust the voltage or add a 6KW regulator
13 "UL" alarm Low voltage alarm Adjust the voltage or add a 6KW regulator
14 "CH" alarm Freshness and temperature sensor open
or sho circuit Replace the sensor
15 "AH" alarm Freshness and temperature sensor open
or sho circuit Replace the sensor
Circuit Diagram