VEVOR HT-W6412 User manual

Technical Support and E-Warranty Certificate www.vevor.com/support
ADJUSTABLE OPEN FRAME
SERVER RACK
USER MANUAL
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an estimate
of savings you might benefit from buying certain tools with us compared to the major top brands
and doses not necessarily mean to cover all categories of tools offered by us. You are kindly
reminded to verify carefully when you are placing an order with us if you are actually saving half
in comparison with the top major brands.

THIS MANUAL APPLIES TO THE FOLLOWING SKUS:
HT-W6412 HT-W6415 HT-W6420
NEED HELP? CONTACT US!
[e-mail]
Have product questions? Need technical support? Please feel free to
contact us:
This is the original instruction, please read all manual instructions
carefully before operating. VEVOR reserves a clear interpretation of
our user manual. The appearance of the product shall be subject to the
product you received. Please forgive us that we won't inform you again
if there are any technology or software updates on our product.
ADJUSTABLE OPEN
FRAM SERVER RACK
1

Thank you for purchasing the Performance Series Wall Mount Cabinet
from VEVOR.
Every effort has been made to ensure the accuracy of the information in
this product manual.
Use of Trademarks,Registered Trademarks, and other Protected
Names and Symbols
This manual may make reference to trademarks, registered trade-
marks,and other protected names and/or symbols of third-party com-
panies not related in any way to vevor. Where they occur these refer-
ences are for illustrative purposes only and do not represent an
endorsement of a product or service by vevor, or an endorsement of
the product(s)to which this manual applies by the third-party company
in question. Regardless of any direct acknowledgment elsewhere in
the body of this document, vevor hereby acknowledges that all trade-
marks, registered trademarks,service marks, and other protected
names and/or symbols contained in this manual and related docu-
ments are the property of their respective holders.
Make sure that you assemble this product according to the instructions.
Do not exceed the weight capacity of this product. Overloading this
product might result in injury or property damage. This product can
support the following weight: Ground-mounted load-bearing: 200Ib,
Wall-mounted load-bearing: 100Ib.
This product is intended for indoor use only and should not be used
outdoors.
This enclosure is extremely heavy. Never attempt to move or lift this
COMPLIANCE STATEMENTS
WARNING STATEMENTS
2

enclosure without assistance.
Tipping hazard! Extending multiple components from this enclosure
increases the chance that the enclosure will tip over. To avoid this risk, do
not extend more than one component from the enclosure.
Do not place any items on this enclosure and do not stack the enclosure
on top of another enclosure.
Keep liquid away from this enclosure.
Make sure that you install the enclosure in an area that can handle the
combined weight of the enclosure and the equipment that you intend to
place inside of the enclosure.
This product requires an earth-ground connection. Do not use this
product without an earth-ground connection.
PRODUCT DIAGRAM
Expanded View
3
10
6
1
7
4
2
5
8
4
5
4
8
8
1
1
11
12
3
5
9
913
9
13
9

1 2
3 4
To view manuals, videos, drivers, downloads, technical drawings, and more
visit www.vevor
PACKAGE CONTENTS
Expansion bolts (x 4)
Limit parts (x 8)
Bottom Pallet (x 1)
Top Pallet (x 1)
Top panel (x 1)
Corner piece (x 8)
Center Sections (x 4)
Righ lower Bracket (x 1)
Righ upper Bracket (x 1)
Right corner Brackets (x 4)
Left corner Brackets (x 4)
Left lower Bracket (x 1)
Left upper Bracket (x 1)
Vertical Rails (x 4)
7
6
5
4
3
2
1
14
13
12
11
10
9
8
Vertical Rails
Qty: 4 Left Upper Bracket Qty: 1
Left Lower Bracket
Qty: 1 Left Corner Brackets Qty: 4
4

5 6
7 8
910
11 12
13 14
Right Corner Brackets
Qty: 4 Right Upper Bracket Qty: 1
Right Lower Bracket
Qty: 1 Center Sections Qty: 4
Corner Piece
Qty: 8 Top Panel Qty: 1
Top Pallet
Qty: 1 Bottom Palle Qty: 1
Limit Parts
Qty: 8 M5*10 Cross Head Screw Qty: 145
5

15 16
17
• Electric screwdriver (sold separately)
• Two People (for assembly)
• Earth Ground Connection
• Allen key
REQUIREMENTS
M6 Cage Nuts
Qty: 10 M6*12 Cross Head Screw Qty: 10
Expansion bolts
Qty: 4
6

INSTALLATIO
Note: Two people are required for the Rack assembly.
Adjust the torque of the electric screwdriver to 10
Set the Mounting Depth
1. Align the Left corner Brackets(#4 )and the Right corner Brackets(#4)
with the Center Sections(#8),slide the Corner Brackets overtop of the
Center Sections.(Figure 1)
2. Determine the maximum required mounting depth for the Rack
Mountable Equipment.
3. Slide the Left corner Brackets and the Right corner Brackets,inward
along the Center Sections,and align the Center Sections with the hole on
the Left corner Brackets and the Right corner Brackets.(Figure 2)
Figure 2
4. Insert M5*10 Cross head screws through into the holes in the Corner
Brackets and Center Sections. (Figure 3)
Figure 1
Figure 3
7
58
8
4
4

5. Tighten the M5*10 Cross head screws on the Centre Section Assembly
using Electric screwdriver.
6. Place two Limit parts(#13) on Corner Brackets,Tighten the M5*10
Cross head screws using Electric screwdriver. (Figure 4)
7.Repeat the above steps and assemble other 4 center section
Assemble the Rack
1. Place Vertical Rails（#1）on Center Section Assembly, Secure
with the M5*10 Cross head screws.(Figure 5)
2. Place Vertical Rails （#1）on The other end of Center Section
Assembly, Secure with the M5*10 Cross head screws.(Figure 6)
Figure 4
8
13
1
1
(Figure 5)
(Figure 6)

3. Insert one Center Section Assembly between the Top of the two Vertical
Rails.Ensure the holes in the ends of the Center Section Assembly align
with the holes in the Top of the two Vertical Rails.
4. Tighten the M5*10 Cross head screws on the Vertical Rails using
Electric screwdriver.
6. Place Left lower Bracket （#3）between the Half-frame Assembly,
align the
two holes in the Vertical Rail and Left lower Bracket.
7. Tighten the M5*10 Cross head screws on the Left lower Bracket using
Electric screwdriver.
5. Repeat the above steps and Assemble another half-frame.
9
1
3

8. Place Left upper Bracket（#2）between the Half-frame Assembly,
align the two holes in the Vertical Rail and Left upper Bracket.
9. Tighten the M5*10 Cross head screws on the Left upper Bracket using
Electric screwdriver.
2
10. Place Righ lower Bracket（#7）between the Half-frame Assembly,
align the two holes in the Vertical Rail and Right lower Bracket.
11. Tighten the M5*10 Cross head screws on the Right lower Bracket
using Electric screwdriver.
7
12. Place Right upper Bracket （#6）between the Half-frame Assembly,
align the two holes in the Vertical Rail and Right upper Bracket.
13. Tighten the M5*10 Cross head screws on the Right upper Bracket
using Electric screwdriver.
10
6

14. Place Corner piece（#9）on Center Section Assembly and lower
Bracket(or upper Bracket).There are 8 locations that need to be installed
15. Tighten the M5*10 Cross head screws on the Corner piece using
Electric screwdriver.
9
16. Place Top Pallet （#1）and Bottom Pallet （#2）on the Enclosure.
17. Tighten the M6 Cage Nuts and M6*12 Cross hex head screws on the
Corner piece using allen key
12
18. Place Top panel（#10）on the Enclosure.
19. Tighten the M5*10 Cross head screws on the Top panel using Electric
screwdriver.
11
11
10

LIMITATION OF LIABILITY
1. Insert an M6 Screw through the Grounding Point on the Grounding
Wire and into the Ground Hole located on the bottom of the Rack.
2. Run the Grounding Wire under the Rack’s Frame.
3. Connect the Grounding Wire to an Earth Ground Connection.
In no event shall the liability of vevor (or their officers,directors,employees
or agents)for any damages(whether direct or indirect, special, punitive,
incidental, consequential, or otherwise), loss of profits, loss of business,or
any pecuniary loss, arising out of or related to the use of the product
exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Ground the Rack
12

PRODUCT PARAMETER
Adjustable Open Frame Server RackName
Model HT-W6412 HT-W6415 HT-W6420
15”-40” 15”-40” 15”-40”
12U 15U 20U
585*510*626mm 585*510*759mm 585*510*982mm
710*610*170mm 840*610*170mm 1050*610*170mm
N.W.: 14.15Kg N.W.: 14.45Kg
100 Ibs
200 Ibs
19''
N.W.: 14.95Kg
G.W.: 17.35Kg G.W.: 17.95Kg G.W.: 18.75Kg
Adjustable
Depth
Installation
Width Standard
Height
Ground-Mounted
Load-Bearing
Wall-Mounted
Load-Bearing
Product Size
Package Size
Weight
13

Address：Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi
Shanghai
Imported to USA: VEVOR STORE INC, 9448 RINCHMOND PL #E
RANCHO CUCAMONGA, California, 91730 United States of America
Made In China

Technical Support and E-Warranty Certificate
www.vevor.com/support