VIA Technologies VIA16 User manual

PoE After boot up, solid green indicates PoE is available.
O󰀨 indicates power supply voltage is not su󰀩cient to
supply PoE capability. Flashing green indicates PoE
External Supply value set to 0
STATUS Flashing blue (heartbeat) indicates power and
processor OK; o󰀨 indicates no power.
Fiber Port
LEDS
(17/18)
Green. Intermittent blinking indicates valid link to
other device. Solid red indicates incompatible ber
transceiver.
RJ45 LEDs Amber. Intermittent blinking indicates valid link to
other device. For each pair of ports, the left LED will
show link status of the upper port while the right LED
will show status of the lower port.
Model 6716 VIA16 Ethernet Switch Installation
Guide
6716-300-REV1 05/29/18
The VIA16 is a DIN-mountable, managed 10/100 Ethernet
switch with sixteen copper ports and two gigabit mini GBIC
ports for SFP modules.
This compact switch is designed speccally for sACN
data distribution and is ideal for networks usings Pathport
Gateways, Choreo controllers, Cognito consoles
and NSB or Vignette architectural wall stations, with
Power-over-Ethernet support for up to 12 devices.
POWER
The 6716 is designed to run Class 3 PoE on ports 1-12. Typically
most Pathport and Vignette devices are Class 2 or lower and a 100W
48VDC power supply (P/N 1001-100-48-DIN) will supply enough
power for the switch and 12 connected PoE devices. Observe
correct polarity when wiring DC IN plug.
ETHERNET
All network wiring should follow standard Ethernet rules and be
installed by a qualied person. As part of the installation, all wiring
should be certied under the TIA/EIA-568 standard.
Pathway recommends the use of manufactured rather than
hand-terminated cables. We also recommend 2100-DIN eDIN RJ45
patch which come in lots of 4 and use 3.5” of rail space. These
use standard punch-down female connectors and essentially build
a patch bay in the eDIN enclosure.
Disconnect all power before proceeding with installation.
Securely mount DIN rail (if not already installed in the enclosure).
Hook the upper slots on the back of the plastic extrusion to the DIN
rail and then gently but rmly press on the bottom front corners of
the extrusion to snap the module onto the rail.
Connect the DC IN terminal, after checking that polarity is correct.
The VIA16 will boot up, which may take 15-20 seconds.
Attach required network cables to RJ45 ports. Connect the ber
module(s), if used.
The system is now ready for conguration and testing.
All eld conguration of the VIA16 must be done with Pathscape
software.
Download the software from www.pathwayconnect.com and install.
Set computer’s IP to a static address in the 10.x.x.x range, with
a subnet mask of 255.0.0.0 and default gateway of 10.0.0.1. No
conguration of the computer’s DNS settings should be required.
Plug into the VIA16 and launch the software. Discovery will be
automatic.
Refer to software documentation for description of conguration
options.
OVERVIEW
CONNECTIONS STATUS INDICATORS
INSTALLATION FURTHER CONFIGURATION
PoE-enabled ports (1-12)
Non-PoE Ports (13-16)
EAPS Ring Protect-enabled ports
(Ethernet ports 15-16 and Fiber
ports 17-18)
Ethernet ports are numbered
top to bottom, left to right.
Top row: 1, 3, 5, 7, 9, 11, 13, 15
Bottom row: 2, 4, 6, 8, 10, 12, 14, 16
21 43 65 87 1091211 1413 1615
PoE NON-PoE
- + DC IN 20-50V 10 100Mbit 1000BaseX
PoE
STATU S
18
17

IP Address Static, set at 10.x.x.x (where x is a number
between 0 and 254)
Subnet Mask 255.0.0.0
Default Gateway 10.0.0.1
VLANs Disabled (all ports run as untagged on VLAN
ID #1)
Mgmt VLAN VLAN ID#1
PoE Supply External supply value set to zero watts (PoE
e󰀨ectively disabled)
Port PoE Enabled. Above value must be set >5W
before a PoE device will boot
QoS O󰀨
Port Link Auto-negotiate
DHCP Disabled
IGMP Disabled
Art-Net to sACN
Conversion
Disabled
Art-Net Alternate
Mapping
Enabled (only applies when above
feature is enabled)
2100-DIN eDIN RJ45 patch (lot of 4) (3.5” of rail for 4)
1001-100-48-DIN 100 Watt, 48VDC Power Supply,
DIN-mountable
Model 6716 VIA16 Ethernet Switch Installation
Guide
6716-300-REV1 05/29/18
Pathway Connectivity Solutions
#103—1439 17Avenue SE Calgary AB
Canada T2G 1J9
[email protected]
www.pathwayconnect.com
tel [phone] fax [phone]
APPLICATION EXAMPLE
DEFAULT SETTINGS
• Power input:
• Switch Only: 20-50 VDC, 10 watts maximum
• Full PoE Support: 48-50VDC, 190 watts maximum
(180 watts for 12 PoE devices)
• PoE Ports: Class 3, 15.4 watts maximum per port, x12
ELECTRICAL INFORMATION ACCESSORIES
REV.01321
eDIN4-PORT DMX/RDM GATEWAY
Pathway Connectivity
www.pathwayconnect.com
POWERIN
V+ V- GRD V- V+
18-48VDC 6Watts MAX
PORTA
D1-
SHLD COM
D1+ D2- D2+
D1-
SHLD COM
D1+ D2- D2+
D1-
SHLD COM
D1+ D2- D2+
D1-
SHLD COM
D1+ D2- D2+
PORTB PORTC PORTD
SDCARD OK
PROCESSOR
ISOPWR D
ISOPWR A ISOPWRB ISOPWR C
OUTPUTD
OUTPUTA OUTPUTB OUTPUT C
INPUTD
INPUTA INPUT B INPUTC
MICRO-SD
IDENTIFY
ETHLINK ACTIVITY
ETHERNET
802.3AF PoE
1107 eDIN enclosure
Intelligent Fixtures
Pathway Modular Receptacle
(EtherCon)
Console
Choreo Architectural Controller
NSB - 2-Button Master, (2) 4-Button
Local
NSB - 2-Button Master (2) 2-Fader Local,
(1) 1-Fader Local
NSB - 4-Button
Master
NSB - 2-Button Master, (2) 2-Fader Local,
(1) 1-Fader Local
LED Wash Lights
48VDC 100W
Power Supply
6716 VIA16
2100-DIN
eDIN Patch
Building Cat5
Cat5
Patch
Cables
1014-TRM Pathport
Gateway