VIA Technologies COMe-9X90 User manual

DisplayPort ▪ 2 x DisplayPort
Expansion Bus ▪ 4 x PCIe x1
BIOS ▪ AMI eEFI BIOS
▪ 32Mbit SPI flas memory
Video
▪ Wake-on-LAN
▪ System power management
▪ AC power failure recovery
▪ Watc dog Timer (software programmable)
Operating System ▪ Windows 7, XP, XPe and CE 6.0
▪ Windows Embedded System 7
▪ Linux
Hardware Monitoring ▪ CPU temperature reading
▪ CPU fan speed reading
▪ System voltage monitoring
System Memory ▪ 2 x DDR3 1333/1066 SODIMM slots
▪ Supports up to 16GB memory size
COMe-9X90 COM Express Module
and
COMEDB4 Carrier Board
COM Express Module Type
▪ Support basic/compact form factor Type 6
COMEDB4 Carrier Board Specifications
▪ VIA VT2021 Hig Definition Audio Codec
▪ Fintek F71869ED
Audio
Super I/O
BIOS
▪ AMI BIOS
▪ 32Mbit SPI BIOS for uEFI
Front Panel I/O
▪ 1 x SD card slot (SDIO), s ared wit DIO1 pin eader
Rear Panel /O
▪ 1 x VGA port
▪ 1 x COM port
▪ 2 x DisplayPort
▪ 2 x USB 2.0 ports
▪ 2 x USB 3.0 ports
▪ 1 x Gigabit Et ernet port
▪ 6 x Audio jacks (supports multi-c annel audio outputs)
Operating and Storage Humidity
▪ 0% ~ 95% relative umidity
Storage Temperature
▪ -40°C ~ 70°C
Onboard Pin Headers and Connectors
▪ 1 x CD-In connector
▪ 1 x Front Audio pin eader
▪ 1 x COM2 pin eader
▪ 1 x LPT pin eader
▪ 1 x LPC pin eader
▪ 1 x SPI pin eader
▪ 1 x DIO1 pin eader, s ared wit SDIO slot
▪ 1 x DIO2 pin eader (from Fintek F71869ED)
▪ 1 x CPU fan connector
▪ 1 x Serial Port pin eader
▪ 2 x SATA power connectors
▪ 1 x LVDS panel connector (dual-c annel 18/24-bit)
▪ 1 x Inverter connector
▪ 1 x System fan connector
▪ 1 x SMBus pin eader
▪ 1 x I
2
C pin eader
▪ 2 x USB 2.0 pin eaders for four USB 2.0 ports
▪ 1 x Front LAN LED pin eader
▪ 1 x Front Panel pin eader (for HDD LED, Power LED, Switc
and Speaker)
▪ 1 x S/PDIF connector
Form Factor and Dimension
▪ Micro-ATX
▪ 10” x 9.6”
DisplayPort Interface ▪ DisplayPort 1: Support DisplayPort/HDMI interface
▪ DisplayPort 2: Support DisplayPort/HDMI interface
CRT Interface ▪ 1 x VGA port supports up to 2048 x 1536 resolution
C ipset ▪ VIA VX11 Media System Processor
Core
Processor ▪ 1.2GHz VIA Nano
®
X2 E-Series
▪ 1.0GHz VIA QuadCore E-Series (manufacturing optional)
COMe-9X90 Module Specifications
Grap ics ▪ Integrated VIA C-645/640 DX11 3D/2D grap ics
processor and video decoding acceleration
Operating Humidity ▪ 0% ~95% (relative umidity; non-condensing)
Storage Temperature ▪ -40°C ~ 70°C
COM Express Compliance ▪ COM Express
™
Type 6, basic module
Dimension ▪ 95mm x 125mm (3.73” x 4.92”)
Operating Temperature ▪ 0°C ~ 60°C
Controller ▪ Realtek RTL8111G/GS 10/100/1000M PCIe Gigabit
Et ernet Controller
Et ernet
Expansion Buses ▪ 1 x System Management Bus (SMBus) interface
▪ 1 x I
²
C bus
▪ 1 x SDIO interface as default (s ared wit GPIO 4INs
and 4 OUTs via VX11)
▪ 1 x LPC bus
▪ 1 x SPI
▪ Support Express Card, speaker out, reset function,
t ermal protection, suspend/wake signals, power
button, power good and fan control signals
Serial ▪ 2 x Serial ports wit TX and RX signals
SATA ▪ 2 x SATA 3.0 Gbps connectors
Audio ▪ 1 x Hig Definition audio digital interface
LAN ▪ 1 x Gigabit Et ernet port
USB ▪ 2 x USB 3.0 ports
▪ 6 x USB 2.0 ports
Input/Output
Mec anical and Environment
Key Features:
• 1.2GHz VIA Nano
®
X2 E-Series processor
• Supports up to 16GB 1333 DDR3 SDRAM
• DX11 3D/2D grap ics wit MPEG-2, WMV9,
VC1 and H.264 decoding acceleration
• Supports 18/24-bit dual-c annel LVDS panel,
two DisplayPort ports, or two HDMI
®
ports
• Supports two USB 3.0 and six USB 2.0 ports
Top View
Bottom View
Rear Panel I/O
Front Panel I/O
Quick Guide
Onboard Jumpers
▪ 1 x Clear CMOS jumper
▪ 1 x Inverter power select jumper
▪ 1 x LCD panel power select jumper
▪ 1 x COM1 voltage select jumper (+5V/+12V power select option)
▪ 1 x COM2 voltage select jumper (+5V/+12V power select option)
▪ 1 x MiniPCIe slot enabled select jumper
▪ 1 x USB 2.0 port 3 enabled select jumper
▪ 1 x BIOS select jumper (for selecting module/carrier board BIOS)
▪ 5 x AT/ATX mode select jumpers
▪ 1 x EDID power select jumper
Operating Temperature
▪ 0°C ~ 60°C
Onboard Slots, Buttons and Power Connectors
▪ 1 x AUX power connector (for AT mode)
▪ 1 x ATX power connector (for ATX mode)
▪ 1 x MiniPCIe slot
▪ 1 x Power button
▪ 1 x Reset button
▪ 3 x PCIe x1 slots
▪ 2 x SATA connectors
COMEDB4 Carrier Board Layout Diagram
System Monitoring
and Management
Grap ics memory ▪ Optimized Unified Memory Arc itecture (UMA)
supports frame buffer size from 64MB to 1GB (BIOS)
Controller ▪ VIA VT2021 Hig Definition Audio Codec
Audio
Compliance ▪ CE, FCC, BSMI and RoHS
COMe-9X90 Module Layout Diagram
Onboard Slots, Buttons and Power Connectors
LVDS Interface ▪ 1 x LVDS c annel supports dual-c annel 18-bit or
24-bit LVDS panel (VIA VT1636 or C rontel CH7305)
DDR3 SODIMM slot 1
VIA Nano X2 E-Series CPU
CPU fan connector
VIA VX11 Chipset
A1
B1
C1
D1 Pin Connector B
Pin Connector A
DDR3 SODIMM slot 2
SD card slot
VGA DisplayPort 2
COM
Gigabit Ethernet
Line-in
Mic-in
Surround Left/Right
Surround Back Left/Right
Center/Subwoofer
DisplayPort 1
USB 2.0
USB 3.0
Front Left/Right
COMEDB4
COMEDB4
PCIe x1 slots
Connector A
Connector B
SATA connectors
Power button
Reset button
miniPCIe slot
AUX power connector
ATX power connector

For more information on t is and ot er VIA products,
please visit www.viatec .com
Step 2
Install five 8mm ex spacers onto t e carrier board. T e ex spacer must
be placed on top of t e board. From t e bottom of t e board, tig ten
t e ex spacers by using t e M2.5x4mm screws (x5).
VIA Tec nologies, Inc.
1F, 531, Z ong-z eng Road, Xindian District,
New Taipei City 231, Taiwan
Tel: [phone]
Fax: [phone]
Web: www.viatec .com
-A4_L 1 2 PVDD
A4_L 3 4 PVDD
GND 5 6 GND
-A5_L 7 8 GND
A5_L 9 10 -A0_L
GND 11 12 A0_L
-A6_L 13 14 GND
A6_L 15 16 -A1_L
GND 17 18 A1_L
-CLK2_L 19 20 GND
CLK2_L 21 22 -A2_L
GND 23 24 A2_L
-A7_L 25 26 GND
A7_L 27 28 -CLK1_L
NC 29 30 CLK1_L
NC 31 32 GND
DDC_PWR 33 34 -A3_L
NC 35 36 A3_L
NC 37 38 SPCLK
NC 39 40 SPD
LVDS
15
1 FANIO
2 FANPWM
3 GND
SYSFAN
16
5V_DIO1 1 2 12V_DIO1
COM_GPO0 3 4 COM_GPI0
COM_GPO1 5 6 COM_GPI1
COM_GPO2 7 8 COM_GPI2
COM_GPO3 9 10 COM_GPI3
GND 11 12 GND
DIO1
17
1 I2C_CLK
2 I2C_DATA
3 GND
I2C_BUS
19
1 SMB_CLK
2 SMB_DATA
3 GND
SMBUS
20
FP_5V 1 2 FP_5V
FP_5V 3 4 -SATA_LED
-PLED 5 6 -PW_BTN
FP_5V 7 8 GND
NC 9 10 RST_SW
NC 11 12 GND
SPEAK 13 14 FP_5V
KEY 15 16 NC
F_PANEL
18
1 +5V
2 SPDIFO
3 GND
SPDIF
21
CD_IN
1
1 CD_IN_L
2 CD_IN_GND
3 CD_IN_GND
4 CD_IN_R
MIC2_FR_L 1 2 AGND
MIC2_FR_R 3 4 FNT_DET
HP_OUT_R 5 6 MIC2_JD
FNT_IO_SENSE 7 8 KEY
HP_OUT_L 9 10 LINE2_JD
+12V 11 12 +12V
AGND 13 14 AGND
F_AUDIO
2
COM_DCD2 1 2 COM_RXD2
COM_TXD2 3 4 COM_DTR2
GND 5 6 COM_DSR2
COM_RTS2 7 8 COM_CTS2
COM_RI2 9 10 KEY
COM2
3
-LP_STB 1 2 -LP_AFD
LP_D0 3 4 -LP_ERR
LP_D1 5 6 -LP_INIT
LP_D2 7 8 -LP_SLIN
LP_D3 9 10 GND
LP_D4 11 12 GND
LP_D5 13 14 GND
LP_D6 15 16 GND
LP_D7 17 18 GND
-LP_ACK 19 20 GND
LP_BUSY 21 22 GND
LP_SLCT 25 26 KEY
LP_PE 23 24 GND
LPT
4
LPC_AD1 1 2 LPC_33M_CLK
-LPC_RESET 3 4 GND
LPC_AD0 5 6 NC
LPC_AD2 7 8 -LPC_FRAME
LPC_SERIRQ 9 10 LPC_AD3
-LPC_DRQ1 11 12 NC
+5V 13 14 +3.3V
+5V 15 16 +3.3V
GND 17 18 GND
GND 19 20 KEY
LPC
5
DIO2
6
5V_DIO2 1 2 12V_DIO2
GPO34 3 4 GPI50
GPO35 5 6 GPI51
GPO36 7 8 GPI52
GPO37 9 10 GPI53
GND 11 12 GND
1 FANIO
2 FANPWM
3 GND
CPUFAN
7
SER0_TX_CON 1 2 SER0_RX_CON
NC 3 4 NC
GND 5 6 NC
SER1_TX_CON 7 8 SER1_RX_CON
NC 9 10 KEY
SER_PORT
11
VUSB 1 2 VUSB
USBD_T0- 3 4 USBD_T1-
USBD_T0+ 5 6 USBD_T1+
GND 7 8 GND
KEY 9 10 GND
USB2_0/1
9
1 IVDD_IN
2 IVDD_IN
3 BAKLITE_EN
4 BLT_CK
5 BAKLITE_EN
6 BLT_CTRL
7 GND
8 GND
Inverter
14
3VSUS 1 2 -LAN_ACT
3VSUS 3 4 NC
GND 5 6 W_LAN_LED
3VSUS 7 8 GND
KEY 9 10 GND
FLAN_LED
22
SPI_VCC 1 2 GND
-SPI_SS0 3 4 SPI_CLK
SPI_DI 5 6 SPI_DO
KEY 7 8 RESET
SPI
10
2
Installing SODIMM memory
on COMe-9X90 module
Step 1
Align t e notc on t e memory module wit t e protruding wedge on t e
SODIMM slot. Insert t e memory module into t e slot at 30 degrees angle.
Installing COMe-9X90 module
to COMEDB4 carrier board
Step 6
Connect t e CPU fan connector cable.
Step 1
Locate t e carrier board mounting points (x5) and t e connectors (x2).
Step 5
Install t e eatsink on COMe-9X90 module. Secure it wit four M2.5x15mm
screws (wit 3mm plastic was er).
1
Step 3
Align t e pin connectors and mounting points of t e COMe-9X90 module
into t e connectors and ex spacers on t e carrier board respectively. T en
press down t e COMe-9X90 module until t e pin connectors ave been
fully inserted into t e connectors.
Onboard Pin eaders and Connectors
Step 2
Pus down until t e memory module snaps into place. T e memory slot as
two locking mec anisms t at will click once t e memory module as been
fully inserted.
Pins Description
1-2 Enabled COM2 pin eader
to support +5V
2-3 Normal (default)
3-4 Enabled COM2 pin eader
to support +12V
24
JP_COM2_VSEL
23
Pins Description
1-2 Enabled COM1 pin eader
to support +5V
2-3 Normal (default)
3-4 Enabled COM1 pin eader
to support +12V
JP_COM1_VSEL
Pins Description
1-2 Keep CMOS setting (default)
2-3 Clear CMOS setting
36
CLEAR_CMOS
Pins Description
1-2 Enabled USB 2.0 port 3 pin eader. (default)
3-4 Enabled USB 2.0 port 3 pin eader. (default)
28
JP_USBP3_SEL
Pins Description
1-2 Use +5V for t e Inverter power.
2-3 Use +12V for t e Inverter power. (default)
30
IVDD
Pins Description
1-2 Use +5V for t e
LCD panel power.
2-3 Use +3.3V for t e
LCD panel power (default)
34
PVDD
Pins Description
1-2 Enabled Mini PCIe slot.
3-4 Enabled Mini PCIe slot.
29
JP_USBME_SEL
Note: For [29] JP_USBME_SEL to be activated,
t e [28] JP_USBP3_SEL function as to be
disabled.
Onboard Jumpers
Step 4
Secure t e COMe-9X90 module using M2.5x4mm screw. T en apply t e
t ermal paste on top of t e processor and c ipset.
VUSB 1 2 VUSB
USBD_T2- 3 4 USBD_T3-
USBD_T2+ 5 6 USBD_T3+
GND 7 8 GND
KEY 9 10 GND
USB2_2/3
8
1 +5V
2 +12V
3 GND
S_PWR2
12
1 +5V
2 +12V
3 GND
S_PWR1
13
Pins Description
1-2 Select module SPI BIOS (default)
2-3 Select carrier board SPI BIOS
33
BIOS_DIS1
Copyrig t © 2013-2017 VIA Tec nologies, Inc. All rig ts reserved.
Pins Description
1-2 ATX mode (default)
2-3 AT mode
25
JP_AT/ATX_SEL5
Pins Description
1-2 ATX mode (default)
2-3 AT mode
26
JP_AT/ATX_SEL2
Pins Description
1-2 ATX mode (default)
2-3 AT mode
27
JP_AT/ATX_SEL3
Pins Description
1-2 ATX mode (default)
2-3 AT mode
32
JP_AT/ATX_SEL4
Pins Description
1-2 +3.3V (default)
2-3 +5V
31
EDID_PWR
Pins Description
1-2 ATX mode (default)
2-3 AT mode
35
JP_AT/ATX_SEL1
Note:
Due to t e limitation of component eig t at t e bottom side of COMe-9X90,
t e SODIMM memory module installed in t is side (SODIMM2 slot) cannot
be bundled wit eatsink or t ermal pad.