Vibe SLICK s10 User manual

Instruction Manual
To ensure maximum performance and safety,
please follow this manual. Please retain the
manual for future reference after installation
Model: SLICK s10 s12 s15
SUBWOOFERS

Specification
Specifications* SLICK s10 SLICK s12 SLICK s15
Speaker Size 10" (274mm) 12" (323mm) 15" (392mm)
RMS Power 350w 400w 500w
Peak Power 1000w 1200w 1500w
Min input RMS 175w 200w 250w
Sensitivity 88dB 90dB 92dB
Frequency Response 30 - 1700Hz 25 - 1500Hz 20 - 850Hz
Impedance 4ohm 4ohm 4ohm
Mounting Diameter 232mm 275mm 350mm
Mounting Depth 126mm 133mm 168mm
Displacement 0.21Cu.Ft. 0.28Cu.Ft. 0.49Cu.Ft.
Recommended Amp SLICK a0 SLICK a0 SLICK a0
SLICK a1 SLICK a1 SLICK a1
SLICK a7 SLICK a7 SLICK a7
Introduction
This instruction manual is for your safety and must be adhered to at all times. Please read, ensure that you fully understand
the installation and set up procedures as explained and if you are unclear on the installation or set up of your VIBE SLICK
speakers please contact your nearest authorised VIBE dealer.
WARNING
DO NOT EXPOSE THIS PRODUCT TO DAMP OR MOISTURE - doing so may result in fire, shock or damage to the product.
ENSURE GOOD AND CORRECT CONNECTIONS - failure to make the correct connections may result in fire or damage to the product.
KEEP THE VOLUME AT A LEVEL SO YOU CAN STILL HEAR OUTSIDE NOISE - failure to do this may result in an accident. VIBE equipment is
capable of producing sound levels that can permanently damage your hearing. VIBE recommends caution when listening at high volume. For
safe and enjoyable listening the sound should be comfortable and clear without distortion.
CAUTION
Never connect any speaker lead to the car chassis. This can cause severe damage to your speaker /car radio /amplifier.
Before drilling or cutting any holes, investigate the layout of your vehicle thoroughly.
Use caution when working near the fuel / hydraulic lines and electrical wiring.
Observe the correct polarity when wiring, improper phasing may cause a loss of bass response.
Ensure that no moving parts catch on the speaker or grill (e.g. window or door handles, or window glass inside the door)
Installation
The quality of the installation will affect the system performance and reliability.
Contact your nearest authorised VIBE dealer if you are unsure about the installation of this product.
Please mount this unit away from any potential hazards.
Minimising the length of wires will provide higher audio output from the system.
The speaker should be securely fastened to the mounting position using the screws provided.
Pre drill your mounting holes using a drill and position with the template provided.
Be sure to investigate your mounting area thoroughly for electrical wires, brake or fuel lines or fuel tank to prevent causing any damage.
Congratulations on purchasing your SLICK subwoofer, please read this manual in order to
fully understand how to get the best results from your speakers and ensure that all advice on
how to look after your speakers is followed.
Thank you for buying VIBE, we hope you enjoy listening to your product as much as we enjoyed
creating it.
VIBE R&D Division
OWNERS MANUAL
Model: SLICK s10 s12 s15

Run in procedure
VIBE recommends that you follow the run in procedure for the subwoofer detailed below.
When your subwoofer is used for the first time naturally like most brand new items it is very stiff and rigid, it will take time for the
moving parts of this subwoofer to loosen up before the subwoofer will be ready to deliver its full potential.
For the first 30 hours it is recommended that you play the subwoofer initially at low to medium volumes, gradually increasing the
volume level as time progresses.
As a guide, if you listen to your subwoofer for 1 hour every day it will take a month for the subwoofer to run in properly.
You will notice a big change in the sound of the subwoofer over this period, as the spider and surround begin to run in, the sound
will get deeper and harder, also the output of the subwoofer will increase as the suspension loosens up.
The subwoofer is like your cars engine, it needs a few thousand miles before you can drive it to it’s full potential, driving it into the
redline from the first day will mean damage is certain and this kind of damage will not be covered by warranty.
Failure to follow this simple procedure is the most common reason for a subwoofer to fail after a very short period of time.
+ -
wiring configuration
4 Ohm

Installation
The vibe subwoofer can be installed in a variety of different ways, the most suitable will depend upon your application.
Free-air installation
The SLICK Subwoofer can be mounted free-air, this does not mean that the woofer can work without any form of enclosure, what it
does mean is that the enclosure can be very large and therefore the subwoofer can utilise the vehicles boot as an enclosure.
The Subwoofer needs to be mounted to a rigid panel as excess vibration will result in poor sound quality, the panel or baffle, should
also seal the output from the front of the Subwoofer from the output from the rear otherwise poor sound quality known as phase
error will occur. This simply means that the output from the rear of the woofer will cancel out the output from the front resulting in a
loss of bass.
As such an enclosure in free-air applications is so large it is worth noting that the power handling of the Subwoofer is reduced to half
that of the same woofer in a measured enclosure, please take this into account when choosing your amplifier.
The sound quality of a free-air mounted subwoofer will not match that of the same subwoofer mounted in a measured enclosure
however in applications where building a traditional enclosure is impossible free-air mounting will add increased bass response to your
system.
Sealed enclosure installation
The most basic and simple of all speaker enclosures is the sealed enclosure otherwise referred to an acoustic suspension design.
They are called acoustic suspension enclosures because the air inside the box acts like a brake to control the woofer.
The sealed enclosure is the easiest design to build and tune, as long as you work within the minimum and maximum recommended
volumes you cannot get it wrong, the smaller enclosures produce a tighter punchy bass, the larger enclosures produce a deeper
bass. Sealed enclosures offer high power handling, tight response and smooth low end roll off and cone motion is better controlled at
all frequencies because of the constant pressure on the back of the woofer.
Sealed enclosures are ideally suited to rock, jazz and live music
PRODUCT TIGHT BASS DEEP BASS
SLICK s10 1.0 cu.ft 1.5 cu.ft
SLICK s12 1.5 cu.ft 2.0 cu.ft
SLICK s15 1.75 cu.ft 2.5 cu.ft
For twin enclosures simply double the volume. E.G. 2 x SLICK s10 in deep bass enclosure will be 3.00cuft

Enclosure construction
Use at least 3/4 inch MDF (medium density fibreboard) or birch ply to construct your enclosure and at least 3/4 inch is
recommended for the baffle. It is recommend that the panels are glued, screwed and braced with sections of the same material
you have used to build the enclosure. The SLICK woofer is capable of producing internal pressures that can literally blow apart
badly made enclosures, great care needs to be taken with the construction and bracing of your enclosure it is also worth sealing
the joints with a silicone sealer once the glue has dried to make a perfect airtight seal.
NOTE- Do not screw the subwoofer into the enclosure within 24 hours of applying silicone sealer to the joints, the gasses given
off as the silicone cures can perish the surround of the Subwoofer causing a non warranty failure.
Enclosure Volume
To work out the volume required for your enclosure please refer to recommended enclosure volumes specified for your
subwoofer, these are listed in cubic feet, to convert cubic feet to litres multiply the cubic feet by 28.3 If you use this formula
calculating your enclosure size will be easy 1 cubic foot is expressed as 12” x 12” x 12” = 1728 cubic inches

If we require a volume of 2.5ft3then we multiply this by 1728 2.5 x 1728= 4320 cubic inches
We now take 2 known enclosure dimensions that we will use E.G. height and width and divide this figure by them which will give
us the depth, for example our height is 15”, our width is 20”
So our depth is 14.4” for this enclosure
Note : this formula is for the INTERNAL dimensions, please add the thickness of the material used to construct the enclosure to
the formula to give you the outside dimensions.
So assuming we are using 1 inch material we need to add 2 thicknesses to each internal dimension to allow for material top and
bottom so the external dimensions for this enclosure would be 17 x 22 x 16.4 inches
T/S Parameters SLICK s10 SLICK s12
Revc 3.6 Ohm 3.6 Ohm
Fo 46.476 Hz 34.5 Hz
Sd 34.600 sqM 53 sqM
BL 8.33 T 7.309 T
Qms 2.209 3.232
Qes 0.828 0.87
Qts 0.52 0.58
No 0.307% 0.40%
SPLo 88.2 dB 90.1 dB
Vas 30.901 ltr 88.095 ltr
Cms 181.773 u M/N 220.897 u M/N
Mms 64.514 g 72.815 g
Mmd 60.813 m KG 65.8 m KG
SLICK s15
3.6 Ohm
29.057 Hz
85.00 M
12.513 T
2.882
0.681
0.551
0.70 %
92 dB
166.659 m M
185.862 u M/N
162.289 g
148.040 Kg

In order to protect your purchase and aid your
warranty please fill in the following form and
keep it safe for your future reference:
Model Number:
Serial Number:
Purchased From:
Date of Purchase:
KEEP IT SAFE
Staple your receipt here:
Limited Warranty
All VIBE products carry a full twelve months manufacturers warranty, valid from
the date of the original receipt / proof of purchase. In order to
validate this warranty, the warranty card should be returned to VIBE
within seven days of the original purchase date. The original receipt
and packaging should also be retained for this twelve month period.
If at any stage during the warranty period you have a problem with the
product then it should be returned to the point of purchase, with proof of purchase in its
original packaging, complete with no items missing.
If the store is unable to fix the product it may have to be returned to
VIBE this process takes around 7 working days.
A full description of VIBE's warranty information can be found on our
website:
www.vibeaudio.co.uk/warranty
A written version can also be obtained from
VIBE warranty Dept
PO BOX 11000
B75 7WG
Technical enquires
call 09067 031420
call cost 50p per minute
call costs correct at date of publication (01/01/09)
Hours of business 9.00am - 5.30pm
all calls are recorded for training purposes
MIDBASS Distribution
PO Box 11000
B75 7WG

NOTES:

FLATBASS™ 13 SPK Bass speaker cable
There are many powerful bass amplifiers on today’s market – the ever increasing power is putting huge strains on speaker wire
– VIBE present a new breed of speaker cable specially developed for BASS applications – the VIBE FLATBASS speaker cable
offers SolidCores™ that can handle and sustain considerably more power than conventional speaker cable.
Model: FlatBass 13 SPK – 13 gauge SolidCore™ flat BASS speaker cable
VIBE 140 amp circuit breaker
Big systems require big protection – The VIBE circuit breaker is rated at a massive 140 amps and offers critical protection to
your system – if the system over powers or short circuits the breaker will cut in and save your equipment. No need to replace
expensive fuses, system is reset via a simple switch – also offers safe and instant system shutdown.
Model: CB140 – 140 amp circuit breaker
FLAT Y 2M / FLAT Y 2F RCA Y leads
Our professional quality full range OFC Y-interconnect guarantees a pure and strong signal. With a flat
design and ferrite loaded gold plated plugs interference is greatly reduced. The FLAT-Y Interconnect is
available in 1 male – 2 female FLAT Y 2F and 2 male – 1 female FLAT Y 2M configurations.
Model: FLAT Y 2f – 1 pair RCA Y lead 1male to 2 female
Model: FLAT Y 2m – 1 pair RCA Y lead 2male to 1female
VIBE SD4/5 subwoofer defender grill
The new VIBE subwoofer defender not only provides protection for your sub but also adds style with its metallic
badge and black rubberised steel construction allow it to integrate perfectly with the VIBE EVO enclosures
Model: SD4 – sub grill fits both 10” and 12” subwoofers
Model: SD5 – sub grill fits 15” subwoofers
VIBE BC10 level controller
The VIBE BC10 gain level controller is a perfect addition to any subwoofer system, the BC10 allows the level of the amplifier to be
controlled from the driver’s seat giving the user easy adjustment of gain level. Particularly useful for adjusting the gain level for
amplifiers controlling subwoofers. The BC10 controller is RCA input and output making it compatible with any system allowing gain
level adjustment of any amplifier it is connected to. It can also be used with full range amplifiers.
Model: BC10 – RCA Gain level control
Slick level remote
A new addition to the Slick range of amplifiers is the Slick level control which allows level adjustment of the amplifier from the front of
the car - Simply plug the supplied cable into the Slick remote level port on the end panel of the amplifier and remote gain control is
yours, it is that easy.
Model: SLR1 – optional remote for use with all Slick amplifiers
VIBE PortPlug™
The VIBE PortPlug allows easy tuning of the VIBE CBR bass enclosures. The PortPlug™ is used to tightly
seal the VIBE TurboPort™ in the enclosure to either create a sealed enclosure for better transient
response or in the case of a multi ported enclosure re-tune the enclosure using only 1 PortPlug™
Model: PP25 – PortPlug™ for 2.5” TurboPort™
Model: PP30 - PortPlug™ for 3” TurboPort™
VIBE official Merchandise
MPS – VIBE polo shirt with embroidered VIBE logo on front and rear
MTS – VIBE T-shirt with small VIBE printed logo on front.
MCD – VIBE CD, containing exclusive VIBE bass tracks as featured on the Bass Tunnel and VIBE Dredd.
MCC – VIBE CD case, metallic silver CD case with VIBE logo.
VFL – VIBE fleece with embroidered logo on the front and large on back.
VTD – VIBE tax disc holder, stylish silver tax disc holder featuring VIBE logo.
VIBE GB41 banana plug
The VIBE GB41 banana plugs are the easy and convenient way to quickly remove your bass enclosure without
having to constantly re-thread your speaker cable into the box terminal, simply attach the speaker cable to the
VIBE GB41 banana plug and you have a reliable quick release solution. Designed for optimum use with the TP-2
and QP-4 terminal, our professional gold plated 4mm banana plugs are polarity marked and feature rubber
shrouds.
Model: GB41 – Gold Banana plug
VIBE FD4 fused distribution block
The VIBE FD4 fused distribution block is a professional AGU fused distribution block which gives easy
connection for up to 4 amplifiers. The VIBE FD4 has 1 x 4AWG input and 4 x 8AWG outputs each
individually fused up to a maximum of 80 amps (AGU fuses available separately)
Model: FD4 – 4 way AGU fused distribution block, 1 x 4 gauge input 4 x 8 gauge outputs
VIBE RT4 / RT8 crimp on ring terminal
The professional range of VIBE RT gold plated ring terminals for connecting power cable to the vehicle
battery. Packed in pairs and include red and black rubber over boots with are easy crimp design.
Model: RT8 – 1 pair of 8 gauge crimp on ring terminals with PVC overboots
Model: RT4 – 1 pair of 4 gauge crimp on ring terminals with PVC overboots
VIBE CT0 / CT4 compression fit ring terminal
The VIBE CT range of gold plated ring terminals are professional compression fit designed for maximum
conductivity when connecting power cable to the vehicle battery. The VIBE RT compression fit terminals are
the best way to connect heavy gauge power cable to the vehicles battery.
Model: CT0 – 0 gauge compression fit ring terminal
Model: CT4 – 4 gauge compression fit ring terminal
VIBE DB6 non fused distribution block
The VIBE DB6 non fused distribution block is a professional non fused distribution block which gives easy
connection for up to 5 amplifiers. The VIBE DB6 has 2 x 4AWG input and 4 x 8AWG outputs which can be
used for power distribution or ground distribution giving a common grounding point for all system
components eliminating the risk of ground loop interference.
Model: DB6 non fused distribution block
VIBE AGU30, AGU60, AGU80 fuses
The VIBE AGU fuse series are the perfect companion to the VIBE FD4 fused distribution block and the Active
and stereo system wiring kits.
Model: AGU30 – 1 pair 30 amp AGU fuses to fit all AGU fuse holders
Model: AGU60 – 1 pair 60 amp AGU fuses to fit all AGU fuse holders
Model: AGU80 – 1 pair 80 AGU fuses to fit all AGU fuse holders
All Accessories are available direct, for next day delivery call 0870 765 8423 or vist www.vibeaudio.co.uk/shop (UK ONLY)
For more product info see www.vibeaudio.co.uk

The CriticalLink™ range of FLAT series cabling from VIBE
The VIBE CriticalLink range of cabling has been developed to achieve the critical link between source (headunit), amplifier and speakers –
VIBE audio equipment is high quality, using anything less than the VIBE CriticalLink™ range of cables will severely compromise your
equipment and will not allow it to perform to its maximum potential.
NOTE: Your audio equipment will only ever be as good as the cables you use to connect it. The link between your audio equipment is critical
for a bigger cleaner sound.
VIBE cabling and interconnects can enhance your system power and sound quality by more
than 20% over other brand cable.
FLATSTEREO™ High Definition full range Interconnect
The VIBE FLATSTEREO RCA is an OFC high definition full range interconnect – delivering the fullest signal possible from source to
amplifier - the cable make up has been developed to run flat with left and right cables running parallel both with individual screening but
sharing an outer FLAT jacket easing installations.
Available in:
Model: FlatStereo RCA 1m – 1 metre full range interconnect
Model: FlatStereo RCA 5m - 5 metre full range interconnect
FLATBASS™ – SolidCore™ Bass interconnect
The VIBE FLATBASS™ interconnect has been specifically developed for use in BASS SYSTEMS - the cable make up has a unique super
FLAT™ design easing installation - Its trick ingredient is oversized SolidCore™ OFC signal wires - allowing a heavier voltage to be passed
down the cable. This is the central wire that caries the main signal from source to amplifier.
Available in:
Model: FlatBass RCA 1m – 1 metre BASS interconnect
Model: FlatBass RCA 5m - 5 metre BASS interconnect
FLATFLEX™ High Definition speaker cable
The delivery of power and signal to the speaker is the final CriticalLink™ in any audio system – VIBES FlatFlex OFC high definition
speaker cable is produced from super fine OFC copper strands collectively picking up all the detail in your music – the multi strands
are aligned in a row making the cable super FLAT™ which can be run invisibly under carpets.
Available in:
Model: FlatFlex 16 SPK – 16 gauge High definition flat flexible speaker cable
Model: FlatFlex 12 SPK – 12 gauge High definition flat flexible speaker cable
FLATLINES™ Power and Ground Cable
VIBE FlatLines™ power cable has been developed to maximises voltage transfer from battery to amplifier - The cable has 2 main lines
running side by side which are made up of fine copper strands - This design makes the cable flat allowing us to make very slim heavy duty
power cable which is highly flexible easing installation.
Available in: system kits, by the roll or by the metre
Model: FLATLINES 8 PWR – 8gauge red power cable Model: FLATLINES 8 GND – 8gauge black power cable
Model: FLATLINES 4 PWR – 4gauge red power cable Model: FLATLINES 4 PWR – 4gauge red power cable
Model: FLATLINES 0 PWR – 0gauge red power cable Model: FLATLINES 0 GND – 0gauge black power cable
BASS SYSTEM KIT
The VIBE 3000watt BASS KIT is specifically designed to gain maximum output from high power Bass systems. Featuring the best BASS specific
cables from the VIBE CriticalLink™ Range.
Contents of this Kit:
FLATLINES™ 4AWG PWR Power and Ground cable
FLATBASS™ RCA SolidCore™ Interconnect
FLATBASS™ 13 SPK Bass speaker cable
FLATLINES ™ remote 18
VIBE 140 amp circuit breaker
All cable is terminated with crimped terminal rings in place and accessory fitting kit
COMPATIBILITY
This kit is compatible with the majority of amplifiers on the market – VIBE recommends this kit for all VIBE BASS monoblock amplifiers new, current
and old models.
Model: Bass Kit – Bass specific amplifier wiring kit
STEREO SYSTEM KIT
The VIBE 1500 watt STEREO KIT is specifically designed to gain maximum output from high power full range systems. Combining the best full
range cables from the VIBE CriticalLink ™ range.
Contents of this Kit:
FLATLINES™ 8AWG PWR Power and Ground cable
VIBE FLATSTEREO™ RCA - OFC high definition full range interconnect
FLATLINES ™ remote 18
FLATSTEREO™ speaker cable
AGU Fuse Holder
All cable is terminated with crimped terminal rings in place and accessory fitting kit
COMPATIBILITY
This kit is compatible with the majority of amplifiers on the market – VIBE recommends this kit for all VIBE full range STEREO amplifiers new,
current and old models. FLATLINES™ 8 PWR Power
Model: Stereo Kit – full range stereo amplifier wiring kit
ACTIVE SYSTEM KIT
The VIBE 1500watt ACTIVE BASS KIT is specifically designed to gain maximum output from high power Active Bass systems (Bass Boxes).
Featuring BASS specific components from the VIBE CriticalLink™ range.
Contents of this Kit:
FLATLINES™ 8AWG PWR Power and Ground cable
FLATBASS™ RCA SolidCore™ Interconnect
FLATLINES ™ remote 18
AGU Fuse Holder
FastPlug™
COMPATIBILITY
This kit is compatible with the majority of amplifiers on the market – VIBE recommends this kit for all VIBE active bass enclosures new, current and
old models.
Model: Active Kit – Bass specific active enclosure wiring kit
The VIBE FastPlug™ (pat. pending), is a product long overdue. Designed and developed by VIBE Engineers the plug
offers safe, fast removal of your active bass enclosure (bass box) or amplifier. You may wish to remove your
system for security reasons, or for the full use of your boot space, whatever the reason the VIBE FastPlug makes
it easy and safe.
The plug is a heavy duty connector that connects positive, negative and remote wires. It is made up of 2 parts –
one end to connect to your equipment and the other to your power source – made from high quality ABS plastic
the device is tough and hard wearing. Model: FASTPLUG
The Deltabox line driver is the ideal solution for those looking to install multiple amplifiers from a single RCA preout. Most people use
RCA “Y” splitters for this task unaware of the signal degradation caused. The Deltabox not only divides the signal but also isolates and
boosts the signal up to a maximum of 9 volts independently for each of the 3 output channels giving much cleaner sound and
excellent signal to noise ratio. For SPL competition the Deltabox is an essential tool as each of the outputs can be split 4 times giving
control of 12 amplifiers from a single gain enabling precise adjustment of the system without having to reset every amplifier
individually. Additionally if your headunit has a weak preout or you wish to run multiple amps but only have one output the Deltabox™
is your ideal solution. Model: DELTABOX
The VIBE 1.5 farad power capacitor is a must for any high performance audio system. VIBE’s 1.5 farad power capacitor
bridges the gap between the vehicles battery and the amplifiers ensuring rapid smooth current flow resulting in louder
tighter bass and clean crisp midrange and treble. The built in digital voltage display constantly and accurately displays the
systems DC voltage. An all new VIBE power distribution block is built into the top of the capacitor to allow easy wiring into
the system and also will allow 3 amplifiers to be wired directly to the capacitor for maximum current flow to the amplifiers.
Model: PC15
All Accessories are available direct, for next day delivery call 0870 765 8423 or vist www.vibeaudio.co.uk/shop (UK ONLY)
For more product info see www.vibeaudio.co.uk