Vicom VIR-30BL-4N1-2MP User manual

INTRODUCTION
Congratulations on your purchase of this product..
This User Guide suits camera series product. We
adopt the latest technical of sensor and driver. The most
attractive characteristics are night-time vision and van-
dalproof, and widely applicable to day & night, indoor &
outdoor. In addition, it owns the characters of high defini-
tion and stability, strong anti-jamming, rich and real color.
Fixing and using this model are convenient too. It is very
good for you to apply to yours CCTV system.
Please read this instruction manual carefully to en-
sure proper use of the product.
CONNECTING
BRIEF OF PRODUCT
Sensor
Using high-performance image sensor, with millions
of pixels resolution.
* Auto Gain Control (AGC)
Built-in auto gain control (AGC) circuit. The color camera
can get high definition picture in low Lux condition.
* Auto Electronic Shutter (AES)
Built-in auto electronic shutter function.
* Gamma Characteristic
Camera Gamma characteristic is 0.45.
* Scanning Mode
NTSC or PAL mode.
* Night-time Vision
0 Lux with IR LED ON. Adopt TaiWan high quality IR
LED, having very good night-vision effect.
TROUBLE AND SOLUTION
Note:
● Please note the camera’s operating temperature and its using
environment requirement. Avoid using the camera at too high
or too low temperatures. The operating temperature is -10℃-
50℃. (Recommendatory operating temperature is -5℃--40℃.)
● Never make the camera face the sun or bright object. Other-
wise, it will damage the CCD.
● Do not mount the camera near by the radiator or heater.
1. No Picture after providing power
. May be the power supply voltage abnormity, please check the power
supply voltage and pole whether exactitude.
. Please check all the connecting cable and monitors whether be connected
correctly or not.
2. The picture level direction have flowing interference ripples
. May be caused by the power supply AC ripples, it need filter the wave of the
power supply.
. Check the monitor and peripheral equipments used.
3. The picture background color changes continuously
. The fluorescent lamp’s electromagnetic field cause color roll. This is proper
phenomenon of the cameras.
. Reduce the fluorescent lamp numbers or increase the distance between the
camera and the fluorescent lamps can improve it.
. Use power supply external sync. camera can solve it.
4. The picture smear too mass
. The power supply’s voltage unstable.
. Connecting cables not connect correctly or have high impedance.
To prevent fire or shock hazarded. Do not expose the unit
The symbol is intended to alert the user to the presence of
The symbol is intended to alert the user to the presence of
to rain or moisture.
important operating and maintenance (servicing)
Instructions in the literature accompanying the appliance.
uninsulated ‘dangerous voltage’ within the product’s
enclosure that may be of sufficient Magnitude to consti-
a risk of electric shock to persons.
Notes：
●The power supply must through safe attestation. Its output voltage、
current、voltage polarity and operating temperature must match the
camera’s requirement.
●When using the camera in the thunderbolt condition,please note to
mount Anti-thunder device or put off the power supply plug and cable.
●In order to capture high quality pictures, the power supply’s cable and
video output cable should not be too long.
CAUTION:
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK
DO NOT REMOVE COVER OR BANCK NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
RISK OF ELECTRIC. DO NOT OPEN
CAUTION:
To prevent electric shocks and risk of fire hazards,
do NOT use other than specified power source.
DC12V Power Supply
Monitor
Link wire rule：
Power
Video
Video
12V DC
DVR
camera

VIR-30BL-4N1-2MP
Series Color Camera
Specification
Model VIR-30BL-4N1-2MP
Pick Up Element 1/2.9” CMOS sensor
Effective Picture
Elements ( H*V ) 1920*1080
Horizontal Resolution 1080P
S/N Ratio 48dB(min)(AGC closed)
Minimum Illumination 0 Lux (with IR LED ON)
Auto Electronic Shutter 1/60s-1/10000s
Auto Gain Control Auto
White balance Auto
Day and night conver-
sion ICR mechanical switch
IR Project Distance 20M
IR Status Under 10 Lux by CDS
IR Power On CDS Auto Control
Video Output C/A/T/CVBS
Power/Current 12VDC (+/-10%)/ 210mA
Lens 3.6mm
Dimension (mm) 150(L)×65(W)×65(H)
Weight (g) 330
Storage Temperature -30~ +60℃
Operating Temperature -10~ +45℃
Packing List
No Name Number
1. camera 1
2. User Guide 1
Franchiser：
Notes:Before providing power for the
camera, please read this User Guide in
detail!
Do not attempt to disassemble the camera.
If the camera can not work, please contact
local franchiser or our company.
IR Waterproof Camera