Vicon CE-4US1TPC User manual

Vicon part number 8009-8244-00-00 Rev 0112
Page 1
INSTALLATION AND OPERATION MANUAL
CE-4US1TPC
4-PorT EThErnET SwiTCh wiTh UTP/
TwiSTEd CoPPEr and Coaxial CablE
ExTEndEr
The CE-4US1TPC is an unmanaged switch that combines four individual Ethernet data
channels over a single standard COAX or UTP cable. Symmetric bandwidth assures
full bandwidth transmission is maintained over the entire operational distance for both
uploads and downloads with virtually zero packet loss. Bandwidth assurance provides
the ability to transmit multiple cameras on single camera runs with no information loss.
Combined with the CE-(X)COAX series or CE-(X)UTP series multi-port extenders up to
64 cameras can be transmitted to a central location on just 16 cables.
The CE-4US1TPC can be powered using standard camera 12 VDC or 24 VAC power
supplies. It also can be powered by PoE eliminating the need for remote site extra cost
power supplies.
Type tested under NEMA-TS2 environmental standards for extended temperature
operation from -40F° to +167F° (-40C° to +75C°). Certified for use with high-
bandwidth megapixel or HD IP cameras and tested to network packet performance
standards along with major manufacturer compatibility testing.
Fixed managed L2 functions include 802.1p Qos, support of 2k MAC addressing,
learning and aging and a non-blocking switch fabric.
Packaged in a rugged aluminum housing, these units are designed for desktop or stand-
alone mounting. See Figure A on page 4for mounting instructions.
See Figures 1 – 5for complete installation details.
Important Safety Warning:
Read and keep these directions
Heed all warnings
Follow all instructions
Do not use this apparatus near water
Clean only with a dry cloth
Install in accordance with the
manufacturer’s instructions
This installation should be made by a
qualied service person and should conform
to all local codes
See further safety instructions on page 4

Vicon part number 8009-8244-00-00 Rev 0112
Page 2
CAT5/6
Coax UTP
BLACK
BLACK WITH WHITE STRIPE
12 VDC, 24 VAC or POE @ 250 mA, max.
FIGURE 1 – CE-4US1TPC
inSTallaTion and oPEraTion ManUal CE-4US1TPC
TECH SUPPORT: 800.34.VICON (800.348.4266)
FIGURE 2 – POSSIBLE ETHERNET CONFIGURATION
Multiple Configurations are possible. Consult your Vicon Sales Engineer.
≤3,000 ft (914 m) Cat-5
OR
≤5,000 ft (1524 m) Coax
CE-16UTP
NVR
CE-16UTP
PoE Switch
≤328 ft
(100 m) Cat-5
CE-4US1TPC
IP Cameras
IP Cameras
≤328 ft
(100m) Cat-5
IP Cameras
IP Cameras
ExtenderNetwork Switch Coax or UTP
Cat-5
CE-4US1TPC
PoE

Vicon part number 8009-8244-00-00 Rev 0112
Page 3
IinSTallaTion and oPEraTion ManUal CE-4US1TPC
TECH SUPPORT: 800.34.VICON (800.348.4266)
iP CaMEra-End
inSTallaTion (CE-4US1TPC)
Set the S1 10/100BaseT DIP switch to the appropriate rate based on the required maximum data rate and
maximum distance. OFF = 10BaseT; ON = 100BaseT
Set the S2 Master/Slave DIP switch to ON for “Master” mode.
For Extended UTP connection, set the S3 1- or 4-pair DIP switch ON for 1-pair or OFF for 4-pair operation.
For Extended Coax connection, set the S3-1 switch ON.
For systems not utilizing PoE, connect the 12V power supply to the power connector of the CE-4US1TPC. A power adapter connector
is provided to simplify connection.
Connect up to 4 IP cameras to the 10/100BaseT Ethernet port(s) of the CE-4US1TPC using standard Cat5/6 cables, each 100m length
(max).
The link LED on the 10/100 connector should be “ON” to indicate proper connection between the camera and the CE-4US1TPC.
Note: While each standard Ethernet port can operate at either 10 or 100 Mbps, the extended port is 100Mbps max. The recommended total
bandwidth limitation should not exceed 54Mbps and is above the upper limit for transmitting four cameras.
On
Off
S1 S2 S3
FIGURE 3 – POWER LED INDICATORS FIGURE 4 – EXTENDED LED INDICATORS
FIGURE 5 – ETHERNET LED INDICATORS
POWER
RED Power is on
OFF Power is off
TRAFFIC 10/100BaseT
GREEN – Connection is OK,
10BaseT mode
YELLOW Flashing, Trafc
present
–
ORANGE – Connection is OK,
100BaseT mode
OFF No trafc –
TRAFFIC LINK
GREEN Flashing – Connection
is OK with trafc
–
YELLOW – Connection is OK
OFF No connection No connection

Vicon part number 8009-8244-00-00 Rev 0112
Page 4
© 2011 Vicon Industries Inc. All Rights Reserved. Vicon and its logo are registered trademarks of Vicon Industries Inc.
89 ARKAY DRIVE | HAUPPAUGE, NY 11788 | USA
T: 631.952.2288 | F: 631.951.2288 | TOLL FREE: 800.645.9116
WEB: www.vicon-security.com
UK: [phone]
MEChaniCal inSTallaTion inSTrUCTionS
• Read and keep these directions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Install in accordance with the manufacturer’s instructions.
• This installation should be made by a qualified service person
and should conform to all local codes.
• DO NOT bundle UTP or Coax signals in the same conduit as
high-voltage wiring.
• To reduce the risk of fire or electrical shock, do not expose these
products to rain, moisture, dripping or splashing.
• No objects filled with liquids, such as vases, shall be placed on
the equipment.
• DO NOT install the unit in a place where the operating ambient
temperature exceeds 75ºC.
• Make sure that the external power supply output voltage is in the
recommended range.
• Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus (including DVRs) that
produce heat.
• Protect the power cord from being walked on or pinched,
particularly at the power source, convenience receptacles and
the point where they exit from the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• Unplug this apparatus during lightning storms or when unused
for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as when a power supply cord or plug is damaged, liquid
has been spilled, objects have fallen inside the apparatus, the
apparatus has been exposed to rain or moisture, do not operate
normally or has been dropped.
• The main plus is used as the disconnect device and shall remain
readily operable.
WARNING: To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture. This
apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
WARNING: This apparatus is a Class I product. This product
must be connected to a mains socket outlet through
an AC to DC power supply.
WARNING: The mains plug is used as the disconnect device and
shall remain readily operable.
WARNING: For non-PoE applications, unit is to be connected to
a mains socket outlet through a Listed Class I power
supply rated 12 VDC or 24 VAC.
FIGURE A
Dimensions are for the CE-4US1TPC standalone module.
5.125" (130 mm)
4.54" (115 mm)
4.54"
(115 mm)
1.2" (30 mm)
1.2” (30 mm)