Victa TORNADO EDGER TE250 User manual

VICTA
TE250 Edger
Assembly and
Owner’s Manual
WARNING! Read this manual before operating your VICTA Edger.
Not for
Reproduction

IMPORTANT INFORMATION
OIL WARNING
Congratulations on your purchase of a top quality Victa Edger. This instruction manual will aid in the
assembly, operation and maintenance of your new Edger.
Please read carefully to ensure safety and the long life of your product.
Do not operate the unit before reading this manual!
Keep this instruction manual in a safe place for future reference or if service is required on your unit.
Please read the ‘Warranty’ section carefully
• Victa H35 Engine must have 375ml off S.A.E. 30 Oil placed in the Sump
Before starting
NOTE: Failure to comply with the following
instructions will result in engine damage
that is not covered by product warranty.
Not for
Reproduction

Features 1
Unit Features
Safety & Handling 2
Safety Instructions
Hazards
Personal Safety Equipment
Assembly Procedures 5
Unit Details
Wheel Assembly
Handle Assembly
Operating Instructions 10
Operating the Edger
Edging Tips
Starting the Edger
Bail Engagement
Maintenance & Care 13
Cleaning
Belt
Adjustment
Engine Components
Oil Change
Air Filter replacement
Spark Plug Replacement
Maintenance Chart
Questions & Answers 22
Troubleshooting
Accessories & Spare Parts 23
Victa Products
Warranty 24
Warranty Conditions
Table of Contents
Not for
Reproduction

FEATURES
1
Cutting Blade guide
Dual fold handle for
compact storage
Easy to manoeuvre
wheel design
Tilt adjustment for garden
edge maintenance
O
perator presence
b
a
il
for user safety engagement
Ergonomically position
starter cord
Oil Filler Cap
Fuel Tank
Control Bail
Front Roller Rear Wheel
Mu r
Blade
Blade Guard
Exhaust
WARNING
HOT - DO NO T
TOUCH WHEN IN USE
OR AFTER STOPING! Fuel Cap
Lower Handl
e
Spark Plug
Upper Handle
Control Cable
Centre Handle
ON/OFF Switch
Not for
Reproduction

2
Safety Instructions
Transporting the Edger
t 5VSOUIFFOHJOFPGGCZNPWJOHUIF"ON - OFF" switch to the "OFF" position and then turn
the fuel tap to the "OFF" position.
t %JTDPOOFDUUIFTQBSLQMVHMFBE
t %POPUUSBOTQPSUUIF&EHFSJOBWFIJDMFJGUIFSFJTGVFMJOUIFGVFMUBOL
Before using the Edger
• For the Victa H35 engine 375ml of S.A.E 30 oil must be placed in engine sump
before starting engine. Failure to do so will cause engine damage and will void
engine warranty.
t %POPUTUBSUUIF&EHFSVOUJMZPVIBWFTUVEJFEUIFJOTUSVDUJPONBOVBM
t ,OPXUIF&EHFSDPOUSPMTBOEMFBSOIPXUPTUPQUIFFOHJOFRVJDLMZJOBOFNFSHFODZCZ
moving the "ON - OFF" switch to the "OFF" position.
t #FGPSFVTJOHUIF&EHFSFOTVSFUIFDVUUJOHCMBEFBTTFNCMZJTOPUXPSOPSEBNBHFE"MXBZT
replace worn or damaged blade and blade nut.
Note: Damaged or worn blade and blade nut are major hazards.
Use genuine Victa spare parts only.
t $IFDLBMMGBTUFOFSTBOEHVBSETSFHVMBSMZ"MXBZTFOTVSFUIF&EHFSJTJOBTBGFPQFSBUJOH
condition.
t $IFDLGPSHSBTTCVJMEVQBSPVOEUIFFOHJOFBOENVGGMFSXIJDINBZDBVTFPWFSIFBUJOHPS
become a fire hazard.
t %POPUTUBSUUIFFOHJOFVOMFTTUIFCMBEFHVBSEJTTFDVSFMZJOQPTJUJPO
t3FQMBDFCMBEFHVBSEJGXPSOPSEBNBHFE
Operating the Edger
t %POPUVTFXIJMFQFPQMFPSQFUTBSFJOUIFWJDJOJUZPGUIF&EHFSPSXJUIJOUIFPQFSBUJOHBSFB
Ensure that bystanders are a minimum of 15 metres away.
t %POPUPQFSBUF&EHFSJOCBSFGFFUPSPQFOTIPFT"MXBZT8FBSMPOHUSPVTFSTBOEIFBWZ
footwear.
t .BLFTVSFUIFPQFSBUJOHBSFBJTDMFBSPGTUJDLTTUPOFTCPOFTXJSFTUSJOHHMBTTOBJMTBOE
debris before use. Objects could be thrown by the blade and cause injury or damage.
t 4UBSUUIFFOHJOFDBSFGVMMZXJUIGFFUXFMMDMFBSPGCMBEFT%POPUUJMUUIF&EHFSXIFOTUBSUJOH
the engine.
t 4UPQUIFFOHJOFJGZPVMFBWFUIF&EHFSVOBUUFOEFE
t 0QFSBUFPOMZJOHPPEEBZMJHIU
Not for
Reproduction

3
t ,FFQIBOETBOEGFFUBXBZGSPNrotating parts beneath Edger when the engine is running.
t %POPUPWFSTQFFEUIFFOHJOFPSBMUFSUIFHPWFSOPSTFUUJOHT&YDFTTJWFFOHJOFTQFFEJT
dangerous and shortens engine life.
t Never lift or carry the Edger when the engine is running.
t 4UPQUIFFOHJOFCFGPSFQVTIJOHUIF&EHFSBDSPTTHSBWFMQBUITPSSPBET
t 4UPQUIFFOHJOFCFGPSFBEKVTUJOHUIFDVUUJOHEFQUI
t 6TFFYUSFNFDBVUJPOXIFODIBOHJOHEJSFDUJPOPOBTMPQF
t /FWFSQVMMUIF&EHFSUPXBSETZPV(Do Not Reverse) You may slip and pull the machine on
top of your feet.
t 8BMLXJUIUIF&EHFSOFWFSSVO
t "UUIFDPODMVTJPOPGVTFSFMFBTFDPOUSPMCBJMBOEXBJUGPSUIFDVUUJOHCMBEFUPTUPQUIFOUVSO
the engine and fuel tap off.
t"MXBZTTUBSUUIFFOHJOFPOGMBUMFWFMHSPVOE
t/FWFSMFBWFUIFVOJUVOBUUFOEFEXIFOJOVTF
t%POPUMFBWFUIF&EHFSJEMJOHGPSMPOHQFSJPET
(Turn unit off if not in use for longer than 5 minutes)
t%POPUTUBSUUIF&EHFSJOBFMFWBUFEQPTJUJPO(Above ground Level)
Maintaining the Edger
t *GUIF&EHFSCFHJOTUPWJCSBUFBCOPSNBMMZPSJGJUTUSJLFTBGPSFJHOPCKFDU4501UIFFOHJOF
disconnect the spark plug lead from the spark plug and inspect the Edger blade and guard
for any damage.
t 3FQMBDFXPSOPSGBVMUZNVGGMFSBTUIJTXJMMBEWFSTFMZBGGFDUFOHJOFQFSGPSNBODFBOEJODSFBTF
emissions.
t 7JDUBSFDPNNFOETUIBUBMMNBJOUFOBODFSFQBJSBOEJOTQFDUJPOXPSLCFDBSSJFEPVUCZB
Victa Authorised Service Centre.
t 4UPSFUIF&EHFSJOBXFMMWFOUJMBUFEBSFBBXBZGSPNBOZOBLFEGMBNFTTVDIBTUIPTFGPVOEJO
gas hot water heaters.
Refuelling the Edger
t 3FGVFMUIF&EHFSPVUEPPSTPOMZ(The engine must be stopped)
tNote: Ensure the fuel filter is clean and Replace if punctured or damaged!
t %POPUTNPLFXIFOSFGVFMMJOHUIFFOHJOF
Never add fuel or remove the fuel cap when operating the engine.t
If fuel is spilt,t Never start the engine! Move the Edger away from the area of the spill.
Always clean fuel spills immediately.t
Do not create any source of ignition until fuel vapours have dissipated from the spill.t
t 4UPSFGVFMJOBDPPMESZBMXBZTVTFBDPOUBJOFSTQFDJGJDBMMZEFTJHOFEGPSUIFQVSQPTFPG
holding fuel. Victa supplies a 5 litre fuel can as an optional extra.
Note: Plastic containers are unsuitable for fuel storage, except those specifically
designed to hold fuel.
THE EDGER IS INTENDED FOR CUTTING LAWN EDGES ONLY!
DO NOT USE FOR CUTTING WOOD OR STUMP GRINDING!
Safety instructions
Not for
Reproduction

4
The following safety precautions must be strictly observed to avoid the risk of damage or
personal injury.
t $IFDLBMMGBTUFOFSTSFHVMBSMZ"MXBZTFOTVSFUIBUUIF&EHFSJTJOTBGFPQFSBUJOHDPOEJUJPO
t %POPUPQFSBUFUIF&EHFSJODPOGJOFETQBDFTXIFSFFYIBVTUGVNFTDBSCPONPOPYJEFDBO
collect.
t 4UPQUIFFOHJOFXIFOFWFSZPVMFBWFUIF&EHFS
t /FWFSUSZUPDMFBSHSBTTGSPNUIF&EHFSXIJMFUIFFOHJOFJTSVOOJOH
t /FWFSMJGUPSDBSSZUIF&EHFSXIFOUIFFOHJOFJTSVOOJOH
t #ZTUBOEFSTNVTUCFBUMFBTUNFUSFTBXBZEVSJOHPQFSBUJPOPGUIF&EHFSBTSPDLTBOEPUIFS
materials may be thrown at high velocities.
t Never use the Edger unless the guards supplied by Victa are fitted correctly and in good order.
Hazards
A pair of Gloves
Personal Safety Equipment
Recommended safety equipment to wear when working with your Edger
MUFFLER & EXHAUST HOT
DO NOT TOUCH WHEN IN USE
OR AFTER STOPING!
SAFEZONE•
Operation Position - Only operate bail,
push & tilt in this position.
Turn off engine in all other Zones.
START & RE-FUEL ZONE•
Start, refuel & adjust height in this
position only.
ALWAYS TURN OFF ENGINE IN
THIS POSITION
DO NOT push & tilt or operate bail
in this position.
DANGER ZONE•
DO NOT OPERATE ANY
FUNCTION IN THIS POSITION!
Engine must be off when in this position.
Do not tilt or lift the unit in this position.
Remove spark plug when performing maintenance.
E
S
A
F
E
-
Z
O
N
E
S
T
A
R
T
I
N
G
&
R
E
-
F
U
E
L
I
N
G
Z
O
N
D
A
N
G
E
R
-
Z
O
N
E
A set of ear muffs Eye protection A pair of safety boots
NOTE: We Recommend Gloves are to be woren when any kind of Mainteance is performed!
E
Not for
Reproduction

ASSEMBLY PROCEDURES
5
Unit details
1. Edger chassis
Note: The chassis is connected to the upper handle by the control cable.
DO NOT DISCONNECT OR CHANGE THE CABLE SCREWS!
2. Lower handle x 1
3. Centre handle x 1
4. Fastener pack
- knobs & nut x 4
- knobs & bolt x 2
- M8 square neck bolt x 6
- Saddle plates x 2
- M8 nut x 2
- M8 washers x 2
5. Front roller x 1
6. Rear wheel x 1
.BOVBM/PUTIPXOY
2
3
5
6
1
4
x 2
x 4
x 6
x 2
x 2
x 2
Not for
Reproduction

ASSEMBLY PROCEDURES
Assembling the wheels
1. Remove edger and components from the carton.
Note: Remove the upper handle and place on the ground before lifting the Edger
chassis from the carton.
2. Locate the mounting bracket tension knobs x 2,
M8 knob bolts x 2 and washers x 2
3. Screw knobs and washers into the bracket.
'SPOUXIFFMNPVOUJOHCSBDLFU
4. Repeat step 3 for the
3FBSXIFFMNPVOUJOHCSBDLFU
5. Locate the rear wheel assembly post and insert into the right
rear wheel mounting bracket.
Adjust to the desired height & tighten knob firmly.
6. Locate the front roller assembly and insert into the front wheel
UIFNPVOUJOHCSBDLFU4FUUJOHUIFIFJHIUPGCPUISPMMFS
XIFFMBUGPSTUBSUJOHBOETUPSBHFJTSFDPNNFOEFE
Adjust to the desired height & tighten knob firmly.
Wheel assembly
2.
3.
5.
6.
WARNING!
TAKE CARE WHEN ADJUSTING
HEIGHT - KEEP FEET & HANDS
AWAY FROM UNDER EDGER
TO PREVENT STRIKING FROM
UNIT HEIGHT DROPPING.
WARNING! HAND & FINGER PINCH HAZARD
TAKE CARE & USE CAUTION WHEN ASSEMBLING
TO PREVENT PINCHING.
x 2x 2
Bracket
Knob
Washer
6
Not for
Reproduction

ASSEMBLY PROCEDURES
7
Your Edger should include a kit with the following parts.
When folding or unfolding the handles, ensure that the bale cable is
not caught, twisted, kinked or stretched!
Handle assembly
Assembling the handle
1. Insert the bolt through the hole, as shown.
The shoulder bolt should locate into the deck.
2. Lower handle in position as shown, Place one
of the saddle plates onto the protruding bolt.
x 4
x 6
x 2
x 2
Bolt
Handle
Not for
Reproduction

ASSEMBLY PROCEDURES
8
Handle assembly
Note: Ensure the control cable is not twisted,
pinched or damaged when assembling
the dual fold handle.
3.
5.
6.
3. Thread one of the nuts onto the top of the bolt
and tighten with fingers. Then torque the nut
to 17 - 22 Nm Maximum.
4. Repeat steps 1 & 3 on the right side
as shown.
5. Attach the dual fold centre handle
using the knobs and bolts provided.
The knobs should be on the outside,
as shown.
6. Attach the dual fold Upper handle
using the knobs and bolts provided.
The knobs should be on the outside.
As shown.
Nut
/N
Not for
Reproduction

9
ASSEMBLY PROCEDURES
Before using the Edger read the safety instructions!
To avoid damage to the Edger, do not allow string or other material to
wrap around the blade or spindle. Stop the engine, disconnect spark plug
and remove material immediately if this occurs.
Handle assembly
Bail Cable Attachment
1. Remove the bail Tag. 2. Remove bail by springing hook
inwards.
3. Slide cable eyelet over bail hook. 4. Reinsert bail in handle holes
"cable side first".
Operating the Edger
1. 2.
3. 4.
9
REMOVE BAIL
HOOKS
INWARDS
BAIL HOOK
THROUGH EYELET RE-INSE
CABLE SIDE
HOOK FIRST
THEN
RE-INSERT
OTHER HOOK
Not for
Reproduction

10
OPERATING INSTRUCTIONS
t 5IF&EHFSXJMMDVUBMPOHGPPUQBUITESJWFXBZTGMPXFSCFET
similar areas.
t 6TFUIFZFMMPXBSSPXHVJEFPOUIFCMBEFHVBSEUPBMJHOUIF
blade with the edging surface.
Note: The guide will give approximate location of the
cutting blade only!
t $VUBUBTUFBEZQBDF*GUIFCMBEFCFHJOTUPCPHEPXOZPV
are edging to fast. Slow your pace "DO NOT FORCE" the
blade into the ground.
t -JHIUDPOUBDUPGUIFCMBEFBHBJOTUUIFGPPUQBUIFEHFPS
curb is acceptable and will not damage the edger.
t #FTUWJTVBMBQQFBSBODFJTPCUBJOFEXIFOUIFHSBTTJT
dry. Avoid edging in wet soil or grass as the blade guard
might clog or result in an uneven edge. If the blade guard
becomes clogged, stop the engine & remove debris from
the blade guard.
Always remove the spark plug lead when cleaning the blade or guard!
Paths and Kerbs
t 4FUUIFDVUUJOHIFJHIUTPUIBUUIFCMBEFUJQDVUT
approximately 30mm below the surface. The blade
alignment indicator is located on the blade guard.
Align the indicator with the edge of the path or the
curb which is to be cut.
Always cut in a forward direction
Avoid allowing the blade to continually contact any
concrete or other hard edge.
Walls and Fences
t 5PFOBCMFZPVSFEHFSUPDVUSJHIUVQUPBXBMMPS
a fence the right rear wheel must be placed on
the lowest setting. Place the left hand side of the
machine against the vertical surface and cut a
narrow grove between the wall and the lawn.
Note: This operation will produce best results
when the blade is new! If the blade is heavily
worn it will not cut a satisfactory edge!
Note: Always take care to avoid damage to brick work, paths, pavers and tiles!
Cutting Tips
Operating the Edger
Blade
Guide
Not for
Reproduction

11
Starting the Edger
NOTE: Before starting your edger read the engine chapter then set the edger
operating height!
Ensure Fuel filter basket is clean and fitted correctly when filling. Replace if
damaged!
1. Connect spark plug lead. (Ensure the rubber
cover ts rmly onto the spark plug) 2. Fill tank with fuel 1.2 litres of
unleaded fuel.
3. Turn ON-OFF switch to the "ON" position. 4. Turn fuel tap to the "ON" position.
5. Set throttle to the "Choke" position. 6. Pull the engine starter until it engages.
Then pull starter cord briskley until the
engine starts.
OPERATING INSTRUCTIONS
Fuel
Tank
Spark
Plug
ON-OFF
Switch
Zone
Clip
Assemble starter cord & knob through the "Zone Clip" eyelet as shown.
This will assist with starting the engine & will prevent cord backlash damaging
the Edger. Avoid pulling the starter cord beyond the cord length limit.
Always gently return the cord knob recoil - Never release knob to backlash.
Not for
Reproduction

12
If problems arise consult an authorised Victa Service Centre.
t 5PFOHBHFUIFDVUUJOHGFBUVSF5JMUUIFFEHFS
backwards slightly and pull engagement bail
against Edger handle.
NOTE: During engagement the blade will plunge
towards the ground! Take care to ensure
the blade is in position!
t 5PBWPJENJTDVUUJOHUJMUUIFVOJUCBDLXBSETUP
engage the blade before lowering the blade into
the ground!
t )PMEUIFSFXIJMFDVUUJOHJTSFRVJSFE
t 5PEJTFOHBHFUIFDVUUJOHGFBUVSFSFMFBTFUIFCBJM
lever.
Pull to Drive
Release
to stop
Engagement Bail
7. Move Throttle to the "RUN" position. 8. To stop the engine, release the bail
and wait for the blade to stop then
turn "ON-OFF" switch to the "OFF"
position.
IMPORTANT: Turn fuel tap "OFF" after use!
Always store in a level position with both wheels set to "0" height
Never leave the edger running idle!
Cutting Control Operation
OPERATING INSTRUCTIONS
Starting the Edger
Bail Engagement
NOTE: "CHOKE" must be used at all times when starting the engine!
(When engine is HOT or COLD)
Not for
Reproduction

Cleaning
13
tRemove grass build up from the air intakes on the starter cowl, around the engine,
carburettor, and the air filter housing.
t"OZCVJMEVQPGHSBTTPSUXJOFPOTQJOEMFTIPVMECFDMFBOFEBOESFNPWFE
t 5IFVOEFSTJEFPGUIF&EHFSTIPVMECFDMFBOFESFHVMBSMZUPSFNPWFEJSUBOEHSBTTBTBOZ
build up will promote corrosion on the steel baseplate.
t When cleaning the underside of the Edger, tilt the handle back so the front wheel is off the
ground. Tilting in any other direction can cause the oil to contaminate & damage the air
filter causing starting difficulties.
NOTE: Do not leave edger tilted backwards for periods longer than 5 minutes!
t"MXBZTLFFQUIF&EHFSJOUIFVQSJHIUQPTJUJPO%POPUMBZ&EHFSPOJUTTJEF
t A hose can be used to clean the underside of your Edger. Care must be taken to "NOT" get
water into the engine as it may damage the magneto or get into the fuel system.
t 5PQSFWFOUDIBTTJTDPSSPTJPOUIFVOEFSTJEFPGZPVS&EHFSTIPVMECFDMFBOFEJNNFEJBUFMZ
after edging an area which has been recently dressed with sulphate of ammonia or
fertiliser.
t After cleaning run the engine briefly to dry off excess moisture before storing.
Before cleaning the Edger ensure the "ON -OFF" switch is in the "OFF"
position. Turn the fuel tap off and disconnect the spark plug lead.
DO NOT CLEAN THE EDGER WHEN THE ENGINE IS RUNNING!
For Your Safety
t /FWFSVTFUIF&EHFSVOMFTTUIFHVBSETTVQQMJFECZUIFNBOVGBDUVSFSBSFJOQPTJUJPO
t #FGPSFTUBSUJOHUIFFEHFSDIFDLCMBEFTBOECPMUTGPSEBNBHFPSXFBS
t *GZPVTUSJLFBOPCTUSVDUJPOTUPQUIFFOHJOFBOEDIFDLUIFCMBEFGPSEBNBHF
t 4UPQUIFFOHJOFBOEEJTDPOOFDUUIFTQBSLQMVHMFBECFGPSFBEKVTUJOHCFMUUFOTJPOPSGJUUJOH
new blades.
t "DO NOT" lay the Edger on its side!
Use only genuine replacement parts made and guaranteed by Victa, insist on them from your
parts and service dealer.
NOTE: Use of non-genuine blades may void your warranty and could result in
damage or injury
Saftey notes
Not for
Reproduction

Adjusting belt tension
3FNPWFUIFDBCMFDPWFSTJMWFS
3 x phillips head screws
2. Loosen tension arm bolt
4. Engage the bail and check that
the spring stretches by 8-10mm
3. Rotate tension arm slightly and
re-tighten screw.
5. If spring stretch is not 8-10mm
Repeat step 3 until spring is correct! 6. 3FQMBDFUIFDBCMFDPWFSTJMWFS
3 x phillips head screws
NOTE: Always Check blade brake operation after adjustment!
If correct belt adjustment cannot be achieved your belt may need replacing!
Replace belt if worn or damaged! 14
1.
3. 4.
5. 6.
2.
Belt tensioning may need increasing when the following symptoms arise
t 1PPSDVUUJOHt#MBEFGSFRVFOUMZTUBMMJOHSPVOEPSBQQFBSUPTUPQ
t#FMUXPSOt#MBEFXJMMOPUSPUBUFPSSPBUFTJOUFSNJUUFOMZ
Not for
Reproduction

15
4. Install the new blade, washer
(Concave to face blade) & re-t Nut.
3. Remove the split pin, blade nut, washer
& used blade.
6. Loosen the nut 1/4 turn and align
the slot with the spindle hole.
5. Tighten the nut until the conical washer
is at against the blade (41-47Nm)
Blade Replacement
2. Place pin or phillips head screw
driver into the locking hole.
1. Rotate the blade until the locking hole
in the lower pulley & bearing housing
line up.
8. Bend the split pin legs outwards to
rest against the nut.
7. Insert split pin through the slot and
spindle hole until the pin head is against
the nut.
1.
5.
7.
3.
8.
6.
4.
Push pin
inside slot!
2.
Not for
Reproduction

16
Engine - Components
Oil Filler Cap /
Dip Stick
Spark Plug
Air Filter Housing
Muffler
Fuel Tank
Fuel Cap
ON/OFF Switch
Starter grip
Throttle Control
"Choke - Run"
Fuel Tap
Starter
Not for
Reproduction

Engine - Oil Level
Engine - Fuel
H35 Engine must have 375ml S.A.E. 30 Oil placed in the Sump Before Starting Engine
Do not over fill the sump
PRE OPERATION CHECK
1. Clean dirt from around the oil filler cap area.
2. Remove oil filler cap and wipe clean.
3. Dip Oil filler cap/dip stick into engine
(Do not screw in to check)
4. Remove oil filler cap/dip stick and check oil level.
5. If the oil level is low add the recommended oil to the
upper mark on the dipstick.
(375ml S.A.E. 30 Oil - Sump Max Capacity)
6. Always check oil level 3 times.
Note: When the edger is level the oil capacity will
roughly fill/reach the brim of the sump oil filler.
CAUTION! Running the engine with insufficient oil can cause serious
engine damage. Be sure to check engine on a level surface with engine
stopped.
CAUTION! DO NOT USE nondetergent oil or 2 stroke engine oil as it will
shorten the engine service life and will not be covered under warranty.
tH35 ENGINE MUST USE REGULAR UNLEADED PETROL.
FUEL TANK CAPACITY IS 1.2 LITRES
t/FWFSVTF0JMQFUSPMNJYUVSFPSEJSUZGVFM"WPJEHFUUJOHEJSUEVTUPSXBUFSJOUIFGVFMUBOL
t1FUSPMJTFYUSFNFMZGMBNNBCMFBOEJTFYQMPTJWFVOEFSDFSUBJODPOEJUJPOT
t3FGVFMJOBXFMMWFOUJMBUFEBSFBXJUIUIFFOHJOFTUPQQFE%POPUTNPLFBMMPXGMBNFTPSBOZ
ignition source in the area where the engine is refilled or where petrol is stored.
t%POPUPWFSGJMMUIFGVFMUBOL (There should be no fuel in the filler neck) after refuelling.
Make sure the filter basket and fuel tank cap is closed. Ensure fuel cap is properly secured.
t#FDBSFGVMOPUUPTQJMMGVFMXIFOSFGVFMMJOH4QJMMFEGVFMPSGVFMWBQPSNBZJHOJUF*GBOZGVFM
is spilt make sure the area is dry before starting the engine.
t"WPJESFQFBUFEPSQSPMPOHFEDPOUBDUXJUITLJOPSCSFBUIJOHPGQFUSPMWBQPS
t0OMZTUPSFGVFMJOBOBQQSPWFEDPOUBJOFS(Victa Fuel Can)
CAUTION! - KEEP FUEL AND OIL OUT OF REACH OF CHILDREN
MAX
MIN
Oil Dip Stick
Maximum Oil Level
Minimum Oil Level
5.
17
CAUTION! - Always ensure the edger is level and on flat ground when checking or
filling oil! Adjust roller and wheel heights as required.
Not for
Reproduction