Victor Tools 11149 User manual

Cordless Screwdriver 11149 Instructions for Use
Please read and retain these instructions for future reference V002: 09/09/18
Please read this instruction manual thoroughly before starting and ensure you are familiar with
the operation of your new Cordless Screwdriver
Controls;
Pistol Driver:
1. Keyless Chuck
2. Charging port
3. Forward/Reverse Switch
SPECIFICATIONS
Screwdriver:
Voltage: 3.6V (DC)
Torque: 3 (Newton Meter)
Speed (no load): 180RPM
AC Adaptor:
Input: 100V-240V (AC)/ 50-60Hz
Output: 5 Volts (DC)
Charging Time: 3 hours to fully charge
battery for 1 hour usage
1
2
3

Cordless Screwdriver 11149 Instructions for Use
Please read and retain these instructions for future reference V002: 09/09/18
Components:
•Cordless Screwdriver
•AC Adaptor
Accessories:
•32pcs bits
•8 pcs x hex sockets (5mm –12mm)
•2pcs drill bits
•1pc extension bar
•1pc universal joint
Charging the Battery:
Be sure to place the tool on a clean dry surface.
Insert AC adaptor into the Charging Port located on
the back of the unit.
Plug the AC adaptor into the closest wall outlet.
Allow 3 hours for the battery to become fully
charged.
Switch on the mains socket power supply. The red
indicator light will illuminate to show the battery is
charging.
The red light will remain illuminated until the charger is connected (do not charge the
screwdriver for more than 6 hours).
Disconnect AC adaptor from the socket after
charging.
Operation:
•Insert the bit into the chuck until it snaps into
place.
•Grasp the tool firmly with both hands, align the
bit with the screw and press it firmly into the
screw.
•The screwdriver is fitted with a forward/reverse
rocker switch, to change the direction of rotation.
•Start the tool by squeezing the Forward/Reverse
trigger switch. Press the top of the switch to turn
the screw FORWARD (tighten fixings). Press the
bottom of the switch to REVERSE the screw
(loosen fixings).
•To stop rotation, release the switch.
Basic safety precautions should always be followed, failure to follow all instructions listed below,
may result in electric shock, fire and/or serious personal injury.

Cordless Screwdriver 11149 Instructions for Use
Please read and retain these instructions for future reference V002: 09/09/18
Work Area
•Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
•Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
•Keep bystanders, children and visitors away while operating a power tool. Distractions can
cause you to lose control.
Electrical Safety
TO PROTECT AGAINST ELECTRIC SHOCK, DO NOT IMMERSE CHARGING CORD, PLUG OR ITEM
IN WATER OR ANY OTHER LIQUID.
UNPLUG FROM OUTLET WHEN FULLY CHARGED.
DO NOT CHARGE WITH A DAMAGED CORD OR PLUG OR IF THE ITEM HAS BEEN DAMAGED IN
ANY MANNER.
THE USE OF ACCESSORY ATTACHMENTS NOT RECOMMENDED BY COOPERS OF STORTFORD
MAY CAUSE INJURIES AND INVALIDATE ANY WARRANTY YOU MAY HAVE.
NEVER USE THE CORD TO CARRY THE TOOL. KEEP CORD AWAY FROM HEAT, OIL, SHARP
EDGES OR MOVING PARTS. REPLACE DAMAGED CORDS IMMEDIATELY. DAMAGED CORDS
MAY CREATE A FIRE.
BEFORE USE, CHECK THOROUGHLY FOR ANY DEFECTS AND DO NOT USE IF DEFECTS ARE
FOUND. TAKE CARE NOT TO DROP AS HEAVY IMPACTS MAY CAUSE INTERNAL DAMAGE.
•BEFORE CONNECTING, CHECK IF THE VOLTAGE INDICATED ON THE BOTTOM OF THE
APPLIANCE IS IN ACCORDANCE WITH THE MAIN VOLTAGE IN YOUR HOME.
Personal Safety
•STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE COMMON SENSE WHEN OPERATING
A POWER TOOL. DO NOT USE THIS TOOL WHILE UNDER THE INFLUENCE OF DRUGS,
ALCOHOL, OR MEDICATION. A MOMENT OF DISTRACTION HILE OPERATING POWER TOOLS
MAY RESULT IN SERIOUS PERSONAL INJURY.
•DRESS PROPERLY. DO NOT WEAR LOOSE CLOTHING OR JEWELRY. KEEP YOUR HAIR,
CLOTHING, AND GLOVES AWAY FROM MOVING PARTS.
•AVOID ACCIDENTAL STARTING, CARRYING TOOLS WITH YOUR FINGER ON THE SWITCH
INVITES ACCIDENTS.
•DO NOT OVERREACH. KEEP PROPER FOOTING AND BALANCE AT ALL TIMES TO ENABLE
BETTER CONTROL OF THE TOOL IN UNEXPECTED SITUATIONS.
•USE APPROPRIATE SAFETY EQUIPMENT FOR THE CONDITIONS. ALWAYS WEAR EYE
PROTECTION, DUST MASK, NON-SKID SAFETY SHOES, HARD HAT OR HEARING PROTECTION
AS APPROPRIATE.
•DO NOT TOUCH MOVING PARTS. ALLOW THE POWER TOOL ACCESSORIES (BIT AND BLADES
ETC.) TO COOL BEFORE TOUCHING THEM. THEY CAN BECOME EXTREMELY HOT DURING USE
AND CAN BURN YOUR SKIN.

Cordless Screwdriver 11149 Instructions for Use
Please read and retain these instructions for future reference V002: 09/09/18
Tool Use and Care
•Use clamps or other practical ways to secure and support the work piece to a stable
platform. Holding the work piece by hand or against your body is unstable and may lead to
loss of control.
•Do not force tool. Use the correct tool for your application. The correct tool will do the job
better and safer at the rate for which it is designed.
•Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the
switch is dangerous and must be repaired.
•Store idle tools out of reach of children and other untrained persons. Tools are dangerous in
the hands of untrained users.
•Check for misalignment or binding of moving parts. Breakage of parts, and any other
condition that may affect the tool’s operation. If damaged, have the tool serviced before
using.
Service
•Tool service must be performed only by qualified repair personal. Service or maintenance
performed by unqualified personnel may result in a risk of injury.
Maintenance:
•Always switch off and unplug before cleaning.
•Do NOT immerse in water. Do not allow any liquids to get inside the tool. Risk of electric
shock.
•Use only mild soap and a damp cloth to clean the cordless screwdriver.Do NOT use abrasive
cleaners or sharp utensils to clean.
•Wipe with a soft, dry cloth.
PLUG WIRING (UK & IRELAND)
This appliance is fitted with a mains adapter.
DISPOSAL:
•Dispose of all packaging, paper, cartons, plastic and plastic bags in accordance with your
local recycling regulations.
•At the end of the product’s lifespan please dispose of it at an authorised household waste
recycling centre.