Victor Mist Pro 360 User manual

Surface Sanitising System
www.VictorFloorcare.com
CAUTION
Read instructions before using the
Mist Pro 360
This machine is not suitable for
spraying / sanitising electrical items.
KEEP FOR FUTURE REFERENCE
Instruction Manual

Contents - Mist Pro 360 Unit, Hose, Nozzle, Extension Lance.
TECHNICAL CHARACTERISTICS
Voltage ........................... 220 - 240 v 50/60 Hz
Dimensions .................... 530 x 380 x 485H mm
Weight............................. 11 kg
Tank Capacity................. 7 ltr
Flow ................................ 140ml per min
Coverage ........................ 12m2 Per Min
Spray Distance ............... 3m
Droplet Size .....................15 - 30 Microns
Run Time Capacity ......... 50 Minutes (per 7L)
Hose Length .................... 2.5 m
Cable Length ................... 7 m
Pressure .......................... 3.2 BAR
DANGER:
This manual forms an integral part of the machine itself. It must
therefore be kept in a safe place where it is accessible to all
users (operators and maintenance personnel) throughout the life
of the machine.
TYPE OF USE
This appliance was designed for mist disinfecting and sanitising.
It has only been designed for these uses.
DANGER:
The manufacturer can not be held responsible for any damage
due to improper or incorrect use. Any other use releases the
manufacturer from liability for harm to persons and/or property
and invalidates any warranty condition.
IMPROPER USE
Do not use the appliance to: Mist flammable, explosive, corrosive
and toxic substances. Expel hot substances. Do not use the
appliance in areas at risk of explosion. Do not use the appliance
to sanitise electrical equipment.
NOTE: This Appliance is not suitable for misting electrical
devices or equipment.
Important: Always disconnect the machine from power socket
after use.

Fig. 1 Fig. 2 Fig. 3
7
5
1
4
1
2
3
6
Assembly - Connecting the solution tube to the unit
Fig. 5 Fig. 6 Fig. 7
13
9
11
8
10 14
10
9
10
11
10
11
12
11
13
Assembly - Connecting the extension nozzle pipe
Assembling the hoses
- Insert, as far as possible, the sleeve (1 Fig. 1) of the air hose into the nozzle (2 Fig. 1) on the drum.
- To release the sleeve (1 Fig. 2) move the lever (3 Fig. 2) clockwise then pull the sleeve outwards (1 Fig. 2).
- Connect the (4 Fig. 3) sanitising solution delivery hose to the quick coupling (5 Fig. 3); to release it push the quick coupling (5 Fig. 3)
inwards.
- Connect the sanitising solution suction (6 Fig. 4) hose to the quick coupling (7 Fig. 4); to release it push the quick coupling (7 Fig. 4)
inwards.
Rigid pipe assembly for long range misting (if present)
After connecting the air hose to the outlet the drum, do as follows:
- Make sure the lever (8 Fig. 5) is in vertical position then attach the first extension (10 Fig. 5) to the ergonomic handle (9
Fig. 5) of the flexible hose and lock it in place by turning the lever (8 Fig. 5) to the horizontal position.
- Attach the first extension (10 Fig. 6) to the second extension (11 Fig. 6) and lock it in place using the lever (12 Fig. 6) as
described previously for the first extension.
- Attach the misting nozzle (13 Fig. 7) to the second extension (11 Fig. 7) and lock it in place using the lever (14 Fig. 7) as
described above
Fig. 4

Fig. 8
15
16
Filling the Tank
C
E
R
T
I
F
I
E
D
9
9
.
9
9
9
9
%
*
Hygiene Range
For best results and
To avoid risk of
invalidating warranty,
recommended for
use with Victor
Sanitiser Mist
Solution
* 99.9999% effective in inactivating and destroying pathogens when using complete Mist Pro 360 System. System
comprises Mist pro 360 unit applying V-SMS5 Victor Sanitiser Mist Solution. V-SMS5 Victor Sanitiser Mist Solution
Meetsthe requirements of: EN1276, EN1650, EN13697 and EN14476.
Filling the sanitising solution tank
- Remove the cap (15 Fig. 8) and pour the sanitising
solution (suitable for misting purposes only) into the
tank (16 Fig. 8).
NOTE:
For sanitising solution dosing refer to the
manufacturer’s instructions.
- Put the cap back on (15 Fig. 8)
- Do not fill beyond Max Fill Level.
NOTE:
The Mist Pro 360 has been specifically designed to
be used with V-SMS5 Sanitiser Mist Solution.
Incorrect selection of other liquids or solutions with
this device may cause damage and invalidate the
warranty. Damage may include, but is not limited to,
corrosion, pump failure, unsatisfactory mist
performance, lack of sanitised areas.
- V-SMS5 Sanitiser Mist Solution is a ready to use
solution where dilution is not required.
Refills available from www.VictorFloorcare.com

Key Features - Mist Pro 360
Fig. 12
21
Fig. 13
22
Fig. 11
Fig. 9 Fig. 10
21
18
17
19
Storing Cables
- When not in use, wrap power cable around the hooks provided (17-18 Fig 9)
Motor Housing
- To remove the motor housing from the base, release 2 clips (19 Fig 10)
Removing Fluid Tank
- To remove the fluid tank for maintenance purposes, disconnect the fluid line and lift from the base. (20 Fig 11)
Country Specific Power supply
- As standard, your Mist Pro 360 device has been fitted with a UK power cable.
On request this can be changed to a country specific power cable prior to purchase. (21 Fig 12)
Carry Handle
- The appliance is fitted with wheels and can therefore be pulled along using the flexible hose.
- To lift it up, insert your fingers under the handle (22 Fig. 13) on the top of the cover.

Operation Guide - Mist Pro 360
USING THE APPLIANCE
Starting up the appliance
- Insert the plug (21 Fig. 12) into the electrical socket.
- Push the switch (24 Fig. 14) on “I” to start the
expulsion motor; the switch lights up.
- Push the switch (25 Fig. 14) on “I” to start the
sanitising solution pump; the switch lights up.
NOTE:
The expulsion motor and the sanitising solution pump
operate independently; therefore, it is necessary to start
both simultaneously.
Creating Mist Flow
- Ensure both pump and motor switches are on “I”.
- Press trigger to allow mist to expel from the nozzle
(28 Fig 16)
NOTE:
If nozzle releases a jet opposed to a fine mist, ensure
motor switch has been pushed to “I”
If Nozzle releases compressed air opposed to fine mist,
ensure solution pump switch has been pushed to “I”.
Fig. 16
29
Fig. 15
26
27
11
28
10
9
Fig. 14
24
25

Important Information - READ BEFORE USE
Troubleshooting guide
Problem Cause Solution
No power to the unit
Mist is not satisfactory.
Not dispensing solution
No mist / only air being released
Switch not pressed.
Plug not inserted.
Power cut.
Nozzle or fluid line clogged.
Pump or motor not switched on.
Nozzle clogged.
Pump or motor not switched on.
Switch not pressed.
Press the switch.
Insert the plug into the socket.
Check the power Cable connection.
Check and clean the flexible hose and
the misting nozzle.
Check both switches are on.
Clean nozzle.
Clean misting filter
Check both switches are on.
Press the switch.
This instruction manual forms an integral part of the Mist Pro
360 and must be read before use.
All operators of the Mist Pro 360 device should be suitably
instructed before use.
Before use, routine observations and maintenance should be
executed to ensure safe operation. - Failure to carry out
periodical maintenance could cause the equipment to become
unsafe. The manufacturer can accept no responsibility in this
event.
Maintenance and the replacement of parts should only be
carried out by a fully qualified technician.
Please ensure the machine is fully switched off and
disconnected from any power source during routine
maintenance, replacing parts or cleaning of the machine.
Any fluid expelled from the machine may be unsafe due to a
number of factors, including, but not limited to temperature,
pressure or chemical content.
This machine is only intended for applying mist to inanimate
objects. Avoid contact with face, eyes and skin.
Appropriate PPE should be worn whilst operating this
machine.
The Mist Pro 360 is designed for professional use only and
should be kept away from children or untrained persons or
those with limited experience at all times.
When operating any electrical equipment, suitable care and
attention should be given whilst in use.
This machine has been designed for, and is intended for use in
commercial environments only.
The Mist Pro 360 is intended for indoor use only.
The Mist Pro 360 should be stored indoors and never exposed
to extreme temperatures for prolonged periods of time.
- Do not remove plug from wall socket by pulling power cable.
- Do not immerse.
- The use of pressure washers or steam cleaners to clean this
machine is prohibited.
- Intended for indoor use only
- Do not use this machine in the rain.
- Ensure power supply is disconnected from power before
commencing any maintenance or cleaning of the machine.
- The power lead should be unwound from the storage hook
fully before use.
- Ensure filters are kept clean.
- Ensure machine is kept clean. This includes Nozzles and
Hoses.
- Ensure the machine is inspected for damage before and after
use. If visible damage occurs, it should be repaired by a
qualified person.
- Ensure the power cable is inspected for damage before and
after using this machine. If visible damage occurs, it should be
replaced by a qualified person.
- Only use Victor approved parts, hoses and nozzles.
- Ensure the fluid tank is empty before inspecting underneath
the machine.
- Ensure the Mist Pro 360 motor housing is connected to the
drum by both clips on the side before moving.
Use handle provided for moving the machine.
- Only use the hose to move the Mist Pro 360 whilst on
smooth, even surfaces.
- Consider the weight if the machine before lifting.

Important Information - WEEE Compliance
Personal Protective Equipment (PPE)
WEEE Registered Producer: WEE/MM8824AA
The European Community WEEE directive deals with the disposal of
Waste Electrical and Electronic Equipment at the end of its useful life.
Our obligation is to ensure the correct disposal of Electrical and
Electronic Equipment (EEE) we produce when it reaches the end of its
useful life and becomes Waste Electrical and Electronic Equipment
(WEEE).
The WEEE symbol on the product indicates that the product must not be
disposed of with normal household waste. Instead such marked waste
equipment must be disposed of by arranging to return to a designated
collection point for the recycling of waste electrical and electronic
equipment. Separating and recycling this waste equipment at time of
disposal will help to conserve natural resources and ensure that the
equipment is recycled in a manner that protects human health and the
environment. Victor offers our customers the opportunity to return
products at the end of their functional lives to Victor for recycling,
qualifying products are marked with the WEEE symbol shown.
Delivery cost of any authorised product returned to Victor will be at the
expense of the sender.
Only applies to EU countries
Ear Protection Hi-Vis Vest / Jacket Eye Protection Protective Headwear
Face Mask Protective Clothing Safety Gloves Safety Footware
Wet Floor Sign
a full risk assessment should be carried out prior to the use of this machine to determine correct use of PPE
Following a full risk assessment, Personal Protective Equipment (PPE) may be required for certain applications.

ICC Products ltd. Unit 15 & 16 Ace Business Park,
Mackadown Lane, Birmingham B33 0LD (UK)
www.VictorFloorcare.com [e-mail]
Tel: [phone]
Misting / Fogging Device
220 - 240 v 50/60 Hz
1200w Pmax 1300W 5,5A
11kg
MADE IN UNITED KINGDOM
Mod: V-MP360
Cap.ty: 7 I
Air flow 55 l/s
Pump: 16W
Bar / PSI 3.2 / 46
Year: 2020
1 2 3
EN Manufacturer Model Product Name
5678
EN Air Flow Pump Max Pressure Electrical Characteristics
5678
EN
5678
EN Weight Country of Origin WEEE Logo
9 10 11 12
EN
Rating Label
1
2
11
12
4
5
6
7
14
15
13
3
9
IP Code
567
EN CE Code YearProtection Class 2 Symbol
13 14 15
EN
4
Capacity
10
IPX4
8

01/12/2020
Schematic Datagram - Mist Pro 360
Technical Spec. - Mist Pro 360
Mist Pro 360
Model
220 - 240 v
50/60 Hz
Voltage
7 LTR
Tank Capacity
12m²
per min
Coverage
3m
Spray Distance
15 - 30 Microns
Droplet Size
220 - 240 v 50/60 Hz
50 min
(per 7L)
Run Time
Capacity
500 x 380 x 485
Size
2.5m
Hose Length
7m
Cable Length
11kg
Weight
3.2 BAR
Pressure
Rating
Class II
Protection
Class
IPX4
IP Rating

www.VictorFloorcare.com
Victor Floorcare
Unit 15 & 16
Ace Business Park
Mackadown Lane
Birmingham
B33 0LD
0121 706 5771
[email protected]
Contact Information