Vida Designs Panama User manual

Page 01
PANAMA FLAT SCREEN TV UNIT
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
SEC/SW/02/21/PJ1
FOR DOMESTIC USE ONLY

* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
Page 02
PARTS LIST
SEC/SW/02/21/PJ1
Part Code
Part Number Part Description Quantity Carton
1
2
3
4
5
6
7
8
9
10
11
12
13
14
S300-305-019-PJ1-01 Right Side Panel 11/1
Le Side Panel
Right Front Upright
Le Front Upright
Top Panel
Shelf Panel
Front Crossbeam
Base
Back Side Panel
Back Centre Panel
Right Division Panel
Le Division Panel
Right Door
Le Door
S300-305-019-PJ1-02
S300-305-019-PJ1-03
S300-305-019-PJ1-04
S300-305-019-PJ1-05
S300-305-019-PJ1-06
S300-305-019-PJ1-07
S300-305-019-PJ1-08
S300-305-019-PJ1-09
S300-305-019-PJ1-10
S300-305-019-PJ1-11
S300-305-019-PJ1-12
S300-305-019-PJ1-13
S300-305-019-PJ1-14
1
1
1
1
1
1
1
2
1
1
1
1
1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
10
2
10
14
10
13
10
12
10
11
10
10
10
5
10
6
10
4
10
3
10
1
10
7
10
8
10
9
10
9

FITTINGS
TOOLS REQUIRED
Page 03
SEC/SW/02/21/PJ1

Page 04
7 - x1
FRONT CROSSBEAM
STEP 2
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A08
STEP 1
11 - x1
RIGHT DIVISION PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A08
D04
12 - x1
LEFT DIVISION PANEL
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
A
Ø 8 x 30mm
8 - x1
BASE
A
SEC/SW/02/21/PJ1
11
12
7
8
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
D
D
D
D
D
F
C
C
F
C
C
C04
F02
C
C
F

Page 05
STEP 4
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B04
STEP 3
1 - x1
RIGHT SIDE PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A08
2 - x1
LEFT SIDE PANEL
Ø 3,5 x 30mm
SEC/SW/02/21/PJ1
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
A
1 - x1
RIGHT SIDE PANEL
2 - x1
LEFT SIDE PANEL
3 - x1
RIGHT FRONT UPRIGHT
4 - x1
LEFT FRONT UPRIGHT
A
A
A
A
A
A
A
A
BB
B
B
B
2
4
1
2
3
1

Page 06
11 - x1
RIGHT DIVISION PANEL
STEP 6
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B04
STEP 5
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B08
Ø 3,5 x 30mm
Ø 3,5 x 30mm
SEC/SW/02/21/PJ1
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
1 - x1
RIGHT SIDE PANEL
2 - x1
LEFT SIDE PANEL
7 - x1
FRONT CROSSBEAM
8 - x1
BASE
2
1
7
8
12 11
12 - x1
LEFT DIVISION PANEL
B
B
BB
B
B
BB
B
B
B
B
B

Page 07
9 - x2
BACK SIDE PANEL
STEP 8
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
J30
STEP 7
5 - x1
TOP PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B08
10 - x1
BACK CENTRE PANEL
10x10mm
SEC/SW/02/21/PJ1
Please assemble on
a clean soft surface
to avoid damage.
B
B
B
B
5
10
9
9
J
J
J
J
J
J
J
J
J
JJ
J
J
J
J
J
J
J
J
J
J
J
JJJ
J
J
Please assemble on
a clean soft surface
to avoid damage.
Ø 3,5 x 30mm
For your future reference
order number should be here
XXXXX
B
BB
B
B

Page 08
STEP 10
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
STEP 9
13 - x1
RIGHT DOOR
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
C12
SEC/SW/02/21/PJ1
Please assemble on
a clean soft surface
to avoid damage.
I
H
CC
I
I
C
C
C
C
C
C
F
C
C
F
CC
C
CC
C H
H
CC
13
14
Please assemble on
a clean soft surface
to avoid damage.
14
13
6
C
C
C
C
C
C
14 - x1
LEFT DOOR
F
F02
H02
I02
C08
6- x1
SHELF
13 - x1
RIGHT DOOR
14 - x1
LEFT DOOR

Page 09
STEP 12
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
STEP 11
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
E02
SEC/SW/02/21/PJ1
Please assemble on
a clean soft surface
to avoid damage.
E
E
G
G
E
G
G02