Videcon ANTIVANDAL 10x IP SPEED DOME CAMERA User manual

INSTRUCTION MANUAL Ver 2.1
ANTIVANDAL 10x IP SPEED DOME CAMERA |MPEG4 with Motion Tracking
Firmware Ver. 1.2.1a

ANTI
-VANDAL 10x SPEED DOME CAMERA 2/96
This lightning flash with arrowhead symbol is intended to alert the user to the
presence of un-insulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.

ANTI
-VANDAL 10x SPEED DOME CAMERA 3/96
Important Safeguard
1. Read Instructions
Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments / Accessories
Do not use attachments or accessories unless recommended by the appliance manufacturer as they may
cause hazards, damage product and void warranty.
4. Water and Moisture
Do not use this product near water or moisture.
5. Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly
installed product may fall, causing serious injury to a child or adult, and damage to the product. Use only
with a mounting device recommended by the manufacturer, or sold with the product. To insure proper
mounting, follow the manufacturer's instructions and use only mounting accessories recommended by
manufacturer.
6. Power source
This product should be operated only from the type of power source indicated on the marking label.
Precautions
Operating
Before using, make sure power supply and others are properly connected.
While operating, if any abnormal condition or malfunction is observed, stop using the camera
immediately and then contact your Special dealer.
Handling
Do not disassemble or tamper with parts inside the camera.
Do not drop or subject the camera to shock and vibration as this can damage camera.
Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your
quality of camera.
Installation and Storage
Do not install the camera in areas of extreme temperature, which exceed the allowable range.
Avoid installing in humid or dusty places.
Avoid installing in places where radiation is present.
Avoid installing in places where there are strong magnetic fields and electric signals.
Avoid installing in places where the camera would be subject to strong vibrations.
Never expose the camera to rain and water.
NOTICE

ANTI
-VANDAL 10x SPEED DOME CAMERA 4/96
○
1Introduction
Features 6
About Network Function 8
Product & Accessories 9
Parts Name & Functions 10
○
2Installation
DIP Switch Setup 12
Installation using Surface mount on the Ceiling 14
Installation using Flush Mount Ring Bracket 15
Installation using Ceiling Mount Bracket 16
Installation using Wall Mount Bracket 17
Cabling 18
○
3Operation
Checking Before Operation 20
Preset and Pattern Function Pre-Check 20
Start OSD Menu 21
Reserved Preset 21
Preset 22
VST 22
Pattern 23
Group 24
Schedule 25
Other Functions 26
OSD Display of Main Screen 27
○
4How to use OSD Menu
General Rules of Menu Operation 28
Main Menu 28
Display Setup 29
Privacy Zone Mask Setup 30
Motion Setup 31
Function Setup 33
Preset Setup 34
VST Setup 36
Pattern Setup 37
Group Setup 38
Schedule Setup 40
Camera Setup 41
System Setup 43
System Initialize 44
C
ONTENTS

ANTI
-VANDAL 10x SPEED DOME CAMERA 5/96
○
5Network Setup
DDNS Registration 45
Quick Start of Network Connection 46
Initial Setup via a Crossover Cable 48
Guide to Network Setup 51
Case A : Dynamic IP or PPPoE + Personal Router 52
Case B : Static(Fixed) IP + Personal Router 54
Case C : Static(Fixed) IP 56
Case D : Dynamic IP + DSL/Cable Modem 58
Case E : PPPoE + DSL Modem 59
Port Forwarding 60
Starting IP Speed Dome 61
○
6Web Viewer
Web Viewer Screen 62
How does Motion Tracking work? 66
Create, Save, Load Map 68
Preset 69
Group 70
Viewer Interface 71
○
7Admin Tool
Video Tool 72
Control Tool 74
Motion Detection Tool 75
Motion Tracking Tool 76
TCP/IP Tool 78
DDNS Tool 79
SMTP Tool 80
Date & Time Tool 81
Users Tool 82
Firmware Update Tool 83
Default Set Tool 84
Rebooting Tool 84
○
8Appendix
A : Current TCP/IP Setting 85
B : Changing your computer’s IP address and subnet mask 86
C : Port Forwarding 87
○
9FAQ 91
○
10 Specifications 95
Specifications 95
Dimension 96
C
ONTENTS

ANTI
-VANDAL 10x SPEED DOME CAMERA 6/96
Features
Network Video Interface
High frame are using hardware MPEG4 compression.
High frame rate with superior Video Quality
High speed : 30 fps at 720 x 480, 25 fps at 720 x 576
Web Browser based Viewer & i-Pro Multi Viewer supported.
Remote control for Pan/Tilt & Sensor I/O.
Bidirectional Audio support
Support with DDNS Service (www.net4c.net) for Dynamic IP
Hardware based Motion Detection function
Hardware based Intelligent Motion Tracking Algorithm (PMI-M200 Only)
Auto Map Generation (PMI-M200 Only)
Virtual Joystick is inspired by real Joystick (PMI-M200 Only)
Camera Specifications
CCD Sensor : 1/4" Interline Transfer CCD
Zoom Magnification : 10 Optical Zoom, 10 Digital Zoom (Max 100 Zoom)
Day & Night Function
Various Focus Mode: Auto-Focus / Manual Focus / Semi-Auto Focus.
Independent & Simultaneous Camera Characteristic Setup in Preset operation
Powerful Pan/Tilt Functions
Max. 360/sec high speed Pan/Tilt Motion
Using Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path. As a result,
time to target view is reduced dramatically and the video on the monitor is very natural to watch.
For jog operation using a controller, since ultra slow speed 0.05/sec can be reached, it is very easy
to locate camera to desired target view. Additionally it is easy to move camera to a desired position
with zoom-proportional pan/tilt movement.
PTZ(Pan/Tilt/Zoom) Control
With RS-485 communication, max. 255 of cameras can be controlled at the same time.
Pelco-D or Pelco-P protocol can be selected as a control protocol in the current version of firmware.
I
NTRODUCTION
1

ANTI
-VANDAL 10x SPEED DOME CAMERA 7/96
Preset, Pattern,VST, Group, Privacy Mask, Schedule and More…
MAX. 127 Presets are assignable and characteristics of each preset can be set up independently,
such as White Balance, Auto Exposure, Label and so on.
Max. 8 set of VST action can be stored. This enables to move camera repetitively between two
preset positions with designated speed.
Max. 4 of Patterns can be recorded and played back. This enables to move camera to follow any
trajectory operated by joystick as closely as possible.
Max. 8 set of Group action can be stored. This enables to move camera repetitively with
combination of Preset or Pattern or VST. A Group is composed of max. 20 entities of
Preset/Pattern/VSTs.
Privacy Masks are assignable, not to intrude on other’s privacy. (4 Privacy Zones)
7 rules of Schedule can be assigned by day and time. Appropriate actions (such as Home, Preset,
Group, Pattern, VST) can be defined for each rule. Also, it is possible to make rule by Weekday and
weekend to simplify the rule.
OSD(On Screen Display) Menu
OSD menu is provided to display the status of camera and to configure the functions interactively.
The information such as Camera ID, Pan/Tilt/Zoom/Direction, Alarm Input & Output, date/time,
current temperature and Preset can be displayed on screen.
Each display item can be turned on or off independently.
Alarm I/O Functions
2 alarm sensor Inputs and 1 relay output are available.
To reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo
coupler.
The signal range of sensor input is from DC 5.0 to 12.0 volts to adopt various applications.
If an external sensor is activated, camera can be set to move to the corresponding Preset position.
Relay output can be assigned to work with a certain preset.
Reserved Presets for Special Purpose
Most camera characteristics can be set up easily and directly with reserved preset, not entering
into OSD menu. For more information, refer to “Reserved Preset” in this manual and “Direct Key
Command” Manual.
I
NTRODUCTION
1

ANTI
-VANDAL 10x SPEED DOME CAMERA 8/96
About Network Function
This product is only compatible with current versions of the Microsoft Windows OS.
This product operates with Microsoft’s Internet Explorer only.
You must have ActiveX controls enabled on your browser, found in the Options menu.
Some pop-up blockers may block legitimate configuration screens, please disable these
blockers when configuring the IP Speed Dome.
Some hardware manufacturers include a cable/DSL modem, router/firewall, and Ethernet
switch in one device.
If you have no available ports on your router (with integrated switch) you can purchase a
10/100 Ethernet switch to “expand” your Local Area Network
The crossover cable is not wired as a typical straight-through network cable. This cable (or
any crossover) should be used for initial setup of the IP Speed Dome via a PC/laptop.
Please temporarily disconnect any proxy servers associated with Internet Explorer while
configuring the IP Speed Dome.
Modification and Development
The Linux-based operating system and flash memory file system enable advanced users and
application developers to customize the IP Speed Dome. An SDK developer kit is available for
users to interface ActiveX controls and other applications.
Attempts to modify the IP Speed Dome will void all warranties and will not be supported by
manufacturer or its seller. Further development tools and documentation for assistance may be
accessible in future releases. We strongly recommend that inexperienced users DO NOT modify
the firmware of IP Speed Dome.
The manufacturer or its seller will not be held accountable in a user's attempt to modify the IP
Speed Dome that renders the unit inoperable or otherwise.
This document is for Network firmware version 1.2.1a
1
I
NTRODUCTION

ANTI
-VANDAL 10x SPEED DOME CAMERA 9/96
Product & Accessories
Product & Accessories
Main Body Surface Mount Bracket
Screws & Terminal Block Crossover Cable
Options
Ceiling Mount Bracket Wall Mount Bracket
Flush Mount Ring Bracket
I
NT
RODUCTION
1

ANTI
-VANDAL 10x SPEED DOME CAMERA 10/96
Parts Name & Functions
Main Unit / Surface Mount Bracket Back of Main Unit
Dome Cover Do not detach protection vinyl from dome cover before finishing all
installation process to protect dome cover from scratches or dust.
Surface Mount Bracket This is used to install the camera directly on the ceiling. After
separating this cover first and then attach this directly to ceiling.
Camera must be assembled at the last stage.
Do not use this bracket when installing camera on the wall with wall
mount bracket or on the ceiling with ceiling mount bracket.
Lockup Screw Fixes main unit to surface mount bracket.
Cabling Terminal Block During installation, Power, Video, Communication, Alarm Input cables
are connected on to this cabling terminal block.
DIP Switch Adjusts camera ID and protocols.
Ethernet Connector This RJ-45 connector is for network connection and designed to operate
on 10 or 100 Mbps.
Reset Switch Return all settings to their factory defaults. Care must be taken since
you will lose all data made previously.
ACTIVE LED When in use, this Yellow indicator should always be flashing or
flickering. During reboots or power cycling, it may take several
seconds for the unit to initialize and illuminate the indicator.
I
NTRODUCTION
1