Videofied DCV 600 User manual

Product Summary
The Camera Model DCV 600 is a wireless, indoor
motion activated camera designed for use in RSIalarm™
security systems.
The camera includes the following features:
> Lithium batteries for long life
>Wide angle lens
>Infrared LEDs for night illumination
>Standard motion coverage lens (40 ft./12 m distance)
>Dual tamper function provides detection for both
wall and cover tamper
>Transmits check-in/status signal every 8 minutes
Installation Guidelines
For easier installation, programming and RF testing
should be done to check for good communication between
the control panel and all system devices before mounting
system devices. Install the detector and other system
devices in the following order:
>Programming/RF Testing—program detector and all other
devices into the control panel and test RF communication
from each intended device location to the control panel.
>Mounting—mount detector at the tested location.
Programming/RF Testing
The following provides summarized steps for device
programming and testing. For complete details, refer
to the control panel installation manual.
1Loosen bottom screw, separate base
from camera and install batteries.
2Re-attach base to secure
tamper switch.
3Put control panel into
programming/configuration mode.
4Using a programmed alphanumeric
keypad, proceed through menus
until the display shows ADD A
NEW DEVICE.
5Press Yes. The display shows PRESS
PROGRAM BUTTON OF DEVICE.
6Press and release program button
on camera using a paper clip end.
The camera LED flashes. Wait for
keypad display to show CAMERA
(1 - 25) PROGRAMMED.
7Press Yes. The display shows
RADIO RANGE TEST? Press Yes
again. The camera LED starts
flashing and keypad display
shows TEST IN PROGRESS.
8Take camera to its intended mounting location and
make sure LED flashes continuously, indicating good
communication with control panel.
9Press Yes to end radio range test, then press Esc/No.
10 The display shows AREA ASSIGNMENT AREA: 1. Press
either arrow button repeatedly until desired AREA
number appears, then press Yes.
11 The display shows NAME + LOCATION. Enter appropriate
device name/location (up to 16 characters), then press
Yes. The display shows the device number and name
for your verification.
12 Press Yes. The display shows VERIFY DETECTION? Press
Yes again and verify camera operation. For example, wave
your hand in front of camera to activate its LED indicating
detection. (walk test LED)
13 Press Yes to end detection verification.
14 The display shows RECORDING NEW EQUIPMENT?
Repeat steps 1 - 14 for remaining cameras.
15 When finished, exit from configuration mode.
www.videofied.com
Program Button
Screw
INSTALLATION INSTRUCTIONS
Camera Model DCV 600
Manufactured by RSIalarm Document No. 1002-c November 2006

Mounting
> Use proper tools and hardware.
> Mount indoors in a temperature-controlled environment.
> Mount camera 7.5 to 9 ft. (2.3 to 2.8 m) from the floor.
> Mount detector on an outside wall, aimed at area to
be secured.
> Do not aim detector at windows, especially those that
let in direct sunlight, or at heat sources such as lamps,
fireplaces, radiators, and heating vents.
> Do not aim detector at moving objects such as curtains,
fans, or animals weighing more than 40 lbs. (18 kg).
Regulatory Information
FCC Part 15
This device complies with FCC Rules Part 15. Operation
is subject to the following two conditions:
1.) This device may not cause harmful interference
and, 2.) this device must accept any interference that
may be received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved
by RSIalarm, Inc. can void the user’s authority to operate
the equipment
Specifications
Panel Compatibility V-6000
Operating Frequency 915 MHz. 25 frequencies
Radio type Spread Spectrum Bidirectional RF
Power Requirements Three 3.6 V lithium batteries
Battery Type LS14500
Motion detection Lens: Fresnel
Detection distance: 40 ft./12 m
Angle: 90°
Detector type: Dual elements
Weight threshold: 40 lbs./18 kg
Camera sensor CMOS black & white
Video resolution 320 x 240 pixels
Video sequence (in alarm) 5 frames/s for 10 seconds
Video sensitivity .2 lux
Lens Wide-angle 85° (no IR treatment)
Night illumination type Infrared (LEDs)
Night illumination distance 14 ft./ 4.5 m
Operating Temperature 32° - 104° F (0° - +40° C)
Maximum Relative Humidity 70%, non-condensing
Dimensions (LxWxD): 3-1/2 in. x 2-3/4 in. x 2-3/4 in.
(89 mm x 70 mm x 70 mm)
Weight 5.3 oz./150 g (without batteries)
UL Listings 1023 (applied for)
1Separate base from camera.
2Hold camera base against
mounting surface and mark the
two appropriate mounting holes.
3Drill pilot holes and install
anchors where needed.
4Place base on mounting surface
so mounting holes line up with
pilot holes/anchors and secure
base with appropriate screws.
5Install batteries into camera, observing correct polarity.
6Attach camera to base and secure with screw.
4455 White Bear Parkway, Suite 700
White Bear Lake, MN 55110
USA
Toll Free: 877-206-5800
Fax: [phone]
www.videofied.com
© 2007 RSIalarm™ Videofied®is a Registered Trademark of RSIalarm™.
S2View is a registered trademark of RSIalarm™. Specifications subject to change without notice.
Flat Wall Mounting Holes
Corner Mounting Holes
INSTALLATION INSTRUCTIONSCamera Model DCV 600