Videofied DCV250 User manual

Product Summary
The Outdoor P-CAM Model DCV250/DCV650/DCV750 is a wireless,
outdoor motion activated camera designed for use in VIDEOFIEDTM
security systems.
The Outdoor P-CAM includes the following features:
> Totally wireless, battery operated.
> Wide angle lens with infrared LED for night illumination.
> Transmits check-in/status signal every 8 minutes.
> Mobility - Use outdoors or indoors with a fully weather
proof casing withstanding temperatures from -20° to +60°C
(-10°/+140°F).
Installation Guidelines
For easier installation, programming and RF testing
should be done to check for good communication between the
control panel and all system devices before mounting system
devices. Install the Camera and other system devices in the
following order:
>Programming/RF Testing - program Outdoor Camera and
all other devices into the control panel and test
RF communication from each intended device
location to the control panel.
>Mounting - mount Camera at the tested location.
www.videofied.com
Programming/RF Testing
The following provides summarized steps for device
programming and testing. For complete details, refer
to the control panel installation manual.
1Separate base from Outdoor Camera by removing the four
screws.
2Place batteries with correct polarity.
3Put the control panel into conguration mode to add a
new device, using the keypad.
4When prompted by the keypad press the programming
button on the back of the Outdoor Camera.
5Press YES on the keypad. The display shows RADIO
RANGE TEST? Press YES again. The Camera LED starts
ashing and keypad display shows TEST IN PROGRESS.
6Take Camera to its intended mounting location and
make sure LED ashes continuously, indicating good
communication with control panel.
7Press YES to end radio range test, then press ESC/NO.
8The display shows AREA ASSIGNMENT AREA: 1. Press
either arrow button repeatedly until desired AREA
number appears, then press YES.
9The display shows NAME + LOCATION. Enter appropriate
device name/location (up to 16 characters), then press
YES. The display shows the device number and name
for your verication.
10 Press YES. The display shows FUNCTIONAL DEVICE
TEST? Press YES again and verify camera operation.
For example, wave your hand in front of the camera to
activate its LED indicating detection. (walk test LED)
11 Press YES to end detection verication.
12 When nished, exit from conguration mode.
I N S T A L L A T I O N I N S T R U C T I O N S
Outdoor P-CAM Model DCV250/DCV650/DCV750
Made by RSI VIDEO TECHNOLOGIES 1013-c July 2008

Regulatory Information
FCC Part 15
This device complies with FCC Rules Part 15. Operation
is subject to the following two conditions:
1.) This device may not cause harmful interference and,
2.) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved
by RSI VIDEO TECHNOLOGIES can void the user’s authority to
operate the equipment.
Specifications
Panel Compatibility VIDEOFIED VISIO1000/V6000/V7000
Operating Frequency 868/915/920 MHz
Radio type Spread Spectrum Bidirectional RF
Power Requirements Three 3.6 V Lithium Batteries
Battery Type LS14500
Operating Temperature -20°/+60°C (-10°/+140°F)
Maximum Relative Humidity 95%, non-condensing
Dimensions 101.6 mm x 89mm x 114.3 mm
(LxWxD) 4 in. x 3 1/2 in. x 4 1/2 in.
Weight 260.8 g/9.2 oz. (without batteries)
Camera Sensor CMOS black and white
Video Resolution 320 x 240 pixels
Video Sequence (in alarm) 5 frames/s for 10 seconds
Video Sensitivity 0.2 lux
Lens Wide-angle 85 degrees
Night illumination type Infrared (LED)
Approvals CE / EN50131 / EN300220 /IDA (DCV250)
UL / FCC (DCV650)
A-Tick (DCV750)
EMEA SALES
2, rue Alexis de Tocqueville
92160 ANTONY
FRANCE
Phone [phone]
Fax [phone]
© 2008 RSI VIDEO TECHNOLOGIES. VIDEOFIEDTM is a Registered Trademark of RSI VIDEO TECHNOLOGIES.
S2View®is a registered trademark of RSI VIDEO TECHNOLOGIES. Specications subject to change without notice.
USA SALES
4455 White Bear Parkway, Suite 700
White Bear Lake, MN 55110
USA
Phone [phone]
Fax [phone]
www.videofied.com
Mounting
> Use proper tools and hardware.
> Mount detector on an outside wall, aimed at area to be secured.
> Mount camera 2.1m/ 6.9 ft. from the oor.
> Do no aim detector at objects that are always in motion
such as animals weighing more than 18kg/40 lbs.
1Attach gimble mount to mounting sufrace facing the
general detection area.
2Thread Outdoor Camera base onto gimble mount.
3Adjust Gimble mount neck to aim at detection area.
I N S T A L L A T I O N I N S T R U C T I O N S
Outdoor P-CAM Model DCV250/DCV650/DCV750