VIEWONHOME VOH1001 User manual

I N S T A L L A T I O N A N D U S E R M A N U A L
G S M V O H 1 0 0 1

1 . S t at u s / G S M S i g n al I n d i c at o r
2 . P o w e r s t a t u s I n d i c a t o r
3. P an i c ( S O S )
4 . P an e l
5 . S t an d
6 . M o n i t o r i n g M I C
SIM 1 . S I M C a r d S l o t
2 . C o n n e c t
3. P o w e r
4 . A d a p t e r I n t e r f ac e
5 . U S B U p g r ad e P o r t
2 3
-32 - b i t h i g h s p e e d p r o c e s s o r , r e l i a b l e c ap ab i l i t y
- 100% w i r e l e s s D . I . Y .
-B u i l t - i n 1 , 0 0 0 , 0 0 0 R F c o d e s
- S u p p o r t s 1 0 r e m o t e c o n t r o l s an d 1 0 0 w i r e l e s s s e n s o r s .
-T h e a l ar m s y s t e m c an b e c o n t r o l l e d b y S M S , A p p o r p h o n e c al l
-S t o r e s 5 p h o n e n u m b e r s an d 5 S M S n u m b e r s f o r al ar m al e r t
-S u p p o r t s e x i t an d e n t r y d e l a y ar m / al e r t
-W i r e l e s s s e l f - l e ar n i n g c o d e
-A d d i n g n e w ac c e s s o r i e s f a s t an d e a s y
-S u p p o r t s ar m an d d i s ar m b y A p p
-S u p p o r t s r e m o t e m o n i t o r b y A p p
-S u p p o r t s r e m o t e c o n t r o l / ar m / d i s ar m / m o n i t o r b y p h o n e
- S M S f o r p o w e r p o w e r r e c o v e r y an d l o w
-S u p p o r t s g l o b a l G S M 85 0 / 90 0 / 1 80 0 / 1 90 0 M H z
C o n tro l P an e l F e atu re s
F e atu re s
1 . S tatu s / L o w P o w e r I n d i c ato r

B l u e s y s t e m i s ar m e d
B l u e  t h e al ar m h as b e e n t r i g g e r e d
2 . P o w e r / G S M S i g n al I n d i c ato r
P r o d u c t 
S h i e l d 2 0 0
P o w e r s u p p l 
InputA C 1 1 0 ~ 2 4 0 V / 5 0 ~ 6 0 H z
 D C 1 2 V / 1 A
G S M w o r k i n g f r 
85 0 / 90 0 / 1 80 0 / 1 90 0 M H z
S t an d b y c u r r e n 
6 0 m A h
A l ar m c u r r e n 
1 2 0 m A h
B u i l t - i n
7 . 4 V 6 0 0 m A h l i t h i u m
S u p p o r t w i r e l e s s 
1 0 r e m o t e c o n t r o l , 1 0 0 w i r e l e s s d e t e c t o r s
W i r e l e s s r e c e i v i n g f r 
4 33M H z ( ± 7 5 K H z )
S i r e n v 
90 d B
H o u s i n g m a t 
A B S
T e m p e r a t u r  - 1 0 ° C ~ + 5 5 ° C
 ≤80%
( n o n - c o n d e n s i n g )



4 5
Quick Start-up Guide
First
Store a phone number
To interact with the control panel by SMS, by phone call and/or from the app, at least one phone number
must be stored in the control panel. Please refer to the on “Store Phone Numbers” on page
7 of this manual.
Change the language
By default the language of the kit control panel is set to English. If you wish to change the system
language, refer to the “Change system language” on page 12 of this manual. “System
language” refers to the language of the SMS you receive from the control panel.
Arm / Disarm the system
The alarm system can be armed or disarmed by SMS, by App and by phone call.
By SMS
To arm the system: Send “1” by SMS to the number of your system’s SIM card.
To disarm the system: Send “0” by SMS to the number of your system’s SIM card.
By app
Click on “Arm” in the app to arm the system, and “Disarm” to disarm the system. The app is available
for download on the App Store and Google Play.
Register wireless accessories
Control by Phone Call
Method 1
When an alarm has been triggered, the control panel dials the pre-stored phone numbers. When
you pick up the phone, control the panel from distance according to the in the table
below).
Method 2
1. Dial the telephone number of the SIM card in your control panel.
2. Enter your user code, followed by ”#”. ey you press on your phone, you hear one beep
3. Select the to control the panel (see in the table below).
Note
The call will end ally if you do not send any command within 30 seconds.
Voice
Command
Press “1“ Arms the system
Press “0“ -
-
-
-
-
-
-
Stops monitoring without hanging up
Press ““
Press “6“ Turns all sirens
Press “9“
Press “#“ -
-
Exits control by phone call
- Stops call recycles
Note
In GSM mode, the audio monitoring is not limited in
Hard Reset
Press the Connect and the Panic (SOS) simultaneously. Release them 3 beeps.
Wait 10 seconds. The panel beeps twice: the system is restored to default
Stored phone numbers and accessories will also be deleted.
successful.
If the accessory has already been registered, the control panel will beep twice. The first accessory
registered is assigned to zone 1, the second accessory registered is assigned to zone 2, etc. Zones
learn how to rename zones).
Disarms the system and turns the siren off
Stops the built-in siren and the wireless siren (if connected to the control panel)
Turns the wireless siren on (if connected to the control panel)
Turns all sirens off

6 7
Zone setup of accessories
Every detector can be assigned to 4 t categories of zones: Home Mode Zone, Delay Zone,
Normal Zone and 24-H Zone. To assign a detector to a zone, open its case and move its jumpers
according to the drawing below:
D0
D3
D0
D3
D0
D3 D3
D0
A. Home Mode Zone B. Delay Zone C. Normal Zone D. 24-H Zone
Normal zone
When the system is armed, if a sensor is triggered, the siren rings out. When the system is disarmed,
sensors do not trigger an alarm.
24h zone
Regardless the system is armed or disarmed, sensors assigned to the 24h zone can trigger an alarm.
It is recommended to set smoke detectors, gas detectors and outdoor beam sensors in the 24-H zone.
Delay zone
An entry and an exit delay can be set. In such case, sensors assigned to the “Delay Zone” will not
trigger an alarm during the of delay set. For example, if you assign a detector to the
Delay zone and you set the Entry/Exit Delay to 30 seconds, the detector will not trigger an
alarm within 30 seconds you enter your home and within 30 seconds before you leave it so that
you can leave and enter your home without triggering an alarm. Refer to the on page 6
of this manual to learn how to set the entry and exit delay. It is recommended to assign the Door /
Window Contact to the Delay zone.
Home zone
When the system is armed in Home Mode, the sensors assigned to the Home zone do not trigger an
alarm. It is rec
armed in Home Mode when you are home and move inside your home without triggering any alarm.
SMS
IMPORTANT: BEFORE USING FOR THE
FIRST TIME
SAVE A PHONE NUMBER FOR SMS
NOTIFICATIONS. (Refer to
on the opposite column)
Only stored numbers can control and
INSERT A SIM CARD IN THE CONTROL PANEL
Each SMS opera in this user
manual will be illustrated as follows:
You send:
SMS Command
command sent by the user.
The control panel replies:
Control panel’s reply
by the control panel.
The speech bubbles that follow are the
dialogue between the user and the control
panel (SMS sent by the user are in pink, SMS
sent by the control panel are in grey).
The system is in English by default. To
change the system’s language, refer to page
12 of this manual.
Store Phone numbers for SMS
Send:
6
SMS numbers:
1.
2.
3.
4.
5.
Copy, Paste, then Edit
(case
SMS numbers:
1. 067890033
2. 067890022
3. 067890011
4. 067890000
5.
Ok
7
BEFORE STARTING SMS OPERATIONS .
MAKE SURE THE SIM CARD DOES NOT
REQUIRE ANY PINCODE .

8 9
Disarm the System
Send:
0
System disarmed.
Arm the System
Send:
1
System armed.
Home Mode
Send:
2
System in home mode.
Enquiry
Send:
00
System:Disarmed
AC power:on
Entry delay
Exit delay
Siren
Disarm password:1234
Note
The value of default will be changed
er having set up the system.
Store Phone Numbers
Send:
5
Phone numbers:
1.
2.
3.
4.
5.
Copy, Paste, then Edit
(case e):
Phone numbers:
1. 067890033
2. 067890022
3. 067890011
4. 067890000
5.
Ok
Change Zone Name
Send “91~99”. For example for zone 1, send:
91
Zones names:
1.
Copy, Paste, then Edit
(case e):
Zones names:
1.Entrance door alarm
Ok
Note
Zones 1 to 9 can be renamed. The name
of the zone cannot consist of more than
30 characters per line due to SMS
character limit. Zones 10 to 99 cannot be
renamed.

10 11
SMS Alert for Accessory Low ery
(available for two-way acessories such as
Detectors)
For accessories assigned to zones that have
been renamed, an SMS will be sent under
the format “Zone name + low ery”.
Bedroom PIR low
For accessories assigned to zones that have
not been renamed, an SMS will be sent under
the format “Zone number + low ery”.
Zone 10 low
SMS Alert for Accessory Tamper Alarm
(available for two-way acessories such as
Detectors)
For accessories assigned to zones that have
been renamed, an SMS will be sent under
the format “Zone name + tamper alarm”.
Bedroom PIR tamper alarm.
For accessories assigned to zones that have
not been renamed, an SMS will be sent
under the format “Zone number + tamper
alarm”.
Zone 10 tamper alarm.
Entry and Exit Delay Time
Send:
11
Entry delay
Exit delay
Copy, Paste, then Edit
(case
Entry delay
Exit delay
Ok
Note
This can be used if you do not want
to bring a remote control or RFID tag with
you. When the system is armed, you hear
one beep every second to remind you to
leave. The beep rhythm speeds up during the
last 10 seconds. If an intruder is detected,
the alarm will be delayed accordingly.
Siren Volume and Ringing Time
Send:
12
Siren volume(0=Mute,1=High):1
Siren ringing
Copy, Paste, then Edit
(case
Siren volume(0=Mute,1=High):0
Siren ringing
Ok
Disarm Password
Send:
13
Disarm password (4 digits):
1234
Copy, Paste, then Edit
(case
Disarm password (4 digits):
8888
Ok
Set Ringing Times
Send:
19
Ringing
Copy, Paste, then Edit
(case
Ringing
This enables you to the number of
the control panel rings before taking the call.
Ring can be set from 0 to 9. When set to 0,
the alarm system will not ring when being called.

1312
Call repe
If the user does not pick up his phone when
the alarm detects an intrusion, the alarm will
keep re-dialing the number a certain amount
of
Send:
20
Call
Copy, Paste, then Edit
(case
Call
The number of call can be set
from 1 to 9.
Delete all Wireless Accessories
Send:
21
Ok
Change system language
Send the code of the language. For example,
for English, send “0001”.
0001
Ok
Refer to the table below for the full list of
languages:
0001 English
0002 French
0004 Danish
0006 Italian
0007 Swedish
0008 German
0009 Spanish
0010 Finnish
0011 Norwegian
Restore System to Factory by SMS
Send:
0000
Ok
The will be restored to default
values. Stored phone numbers and
connected accessories will also be deleted.
Only stored numbers can send the SMS to
restore factory
Accessories
Wireless Remote Control
Home Mode
Arm
SOS
Disarm
LED indicator
Arm the system
Press the Arm " " to arm the alarm
system. The LED indicator lights up (the siren
rings out once). The system is armed.
If an intruder is detected, the siren rings
out. (The siren turns 5 minutes as
per default In the the
system dials the pre-stored phone numbers
Disarm the system
Press the Disarm " " to disarm the
alarm system. The LED indicator turns (the
siren rings out twice). The system is disarmed.
Home Mode
Press the Home Mode " " on the
remote control. The system state LED is on.
All the sensors in regular zones are armed
except those in the Home Mode zone.
The sensors in the Home Mode zone are
disarmed so that users can move inside their
home.
0016 Czech

1514
Emergency Mode
Regardless the status of the system, the alarm
is triggered when the SOS "SOS" is
pressed on the remote control.
At the same the control panel sends a
by SMS and dials the pre-stored
phone numbers.
Register in the control panel
Press the at the back of the control panel to enter the mode. Press
any on of the remote control.
Power supply:
DC 3V (CR2025 on ba x1)
Oper current:
≤7 mA
St current:
10 uA
Transmission distance
≤80 m (in open area)
Radio-frequency:
433MHz (±75KHz)
Housing material:
ABS plas
c
Temperature: -10°C ~ +55°C
RHumidity: ≤80%
(non-condensing)
Dimensions:
57 x 31 x 11 mm
Wireless Detector
With automa temperature compensa and turbulence technology, it easily
adapts to environmental changes.
Design
Features
3
1
2
1. LED indicator
2. Detection window
3. Bracket
PCB Layout
Alarm zone
setup
Tamper
switch*
Infrared
sensor**
AA 1.5V LR6
Antenna
LED working
indicator
*Tamper switch
When the alarm system is armed, the tamper
switch will trigger the alarm if the case is
opened.
**Infrared sensor
Detects the infrared rays released by human
body Do not touch the surface. Keep
the surface clean.
LED
Blinks self
Blinks once: an intruder is detected
Blinks twice: self is complete; entering working mode.
Blinks once every 3 seconds: under-voltage indica the eries must be replaced. (You will
be informed by SMS when the eries are low if the detector is registered in the control
panel.)
The PIR moon detector is a high performance wireless moon detector boasng a digital
dual-core fuzzy logic infrared control chip with intelligent analysis. This technology idenfies
interferences created by body moon and reduces the false alarm rate.

1716
Usage
Open the case and remove the strip. will start for 30 seconds.
When the sensor is in operation, if it is
triggered more than twice within 3 minutes,
it will switch to standby mode to save power.
If no movement is detected within the next
3 minutes, the sensor goes back to working
mode.
Connect
Register in the control panel
Press the at the back of the control panel to enter the mode.
Press the connect at the back of the sensor or trigger the sensor (by moving in
front of it).
Avoid the detector close to windows, air , heater, refrigerator, oven,
sunshine and places where the temperature changes fast or where the air stream s
frequently.
If two detectors are installed in the same det scope, adjust the loca to avoid interferences
and false alarms.
Fix the bracket on the wall with
screws and ach the detector to the
bracket. Adjust the bracket to change
the det distance and angle. It is
recommended to mount the detector
2m from the ground.
Top
Ground
2.2 m
The detector is more sensitive to
cross movements than vertical
movements.
Side view
Top view
A. the inst turn the detector on. one minute of self-t press the test
walk in the scope of det and watch the LED indicator to make sure the detector
is working.
B. The LED indicator blinks once when body movement is detected.
C. Adjust the detector angle to achieve the best de performance.
Power supply
DC 3V (AA 1.5V LR6 Ba x 2)
St current
≤30uA
Alarm current
≤15 mA
De scope
8m / 110°
Tdistance
≤80m (in open area)
Radio-frequency
433 MHz (±75 KHz)
Housing material
ABS plas
c
Temparature: -10°C~55°C
Rhumidity: ≤80% (non-condensing)
Detector dimensions (L x W x H)
107 x 53 x 32 mm
Bracket dimensions (L x W x H)
52 x 30 x 26.5 mm
Scope
110°
Top view
0m 2m 4m 6m 8m
2m
0m
Side view

1918
Wireless Door / Window Contact
Features
signals to the control panel when the
Thanks to the tamper switch, any t to remove the cover of the Door / Window Contact
will trigger the alarm.
Design
Magnet
Transmitter
LED indicator
PCB Layout
LED working indicator
Zone setting
AAA 1.5V Battery
AAA 1.5V Battery x 1
Tamper switch
LED
Blinks once: the door or window is open and the sends a signal to the control panel.
Blinks quickly: Low power indica the eries must be replaced.
Register the detector in the alarm system
Press the at the back of the control panel to enter the mode. Then
separate the magnet from the er.
To check if the registr is complete, arm the system and separate the magnet from the
again by opening the door or window on which it is installed. If the siren rings out,
the regis is successful.
- Open the case and remove the ery strip.
- Mount the sensor on the door and the magnet on the
door frame.
- Make sure the magnet is placed above the er.
- Mount the magnet max. 1 cm away from the
and secure the and magnet with double-sided
tape or screws.
- Avoid the sensor in areas with a large amount of
metal or electrical wiring such as a furnace or room.
Power supply
current
≤30 uA
Alarm current
≤15 mA
Tr distance
≤80 m (in open area)
Radio-frequency
433 MHz (±75 KHz)
Housing material
ABS
Oper temperature
-10°C~55°C
humidity
≤80% (non-condensing)
Tdimensions (LxWxH)
60 x 45 x 18 mm
Magnet dimensions (LxWxH)
45 x 19 x 17,5 mm
The door/window contact can be installed on doors, windows, and any other objucts that open
and close. The sensor sends signals to the control panel when the magnet is separated from the