ViewSonic DPX1002 User manual

ViewSonic®
Digital Photo Frame
DPX702
-Quick Start Guide
Model No. : VS12078
- Quick Start Guide
- Guide de démarrage rapide
- Guía de Inicio Rápido
Model No. : VS12074
Digital Photo Frame
ViewSonic®
DPX1002

Quick start guide
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modications not expressly
approved by the party responsible for compliance could void your authority to
operate the equipment.
For Canada
• This Class B digital apparatus complies with Canadian ICES-003.
• Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
CE Conformity for European Countries
The device complies with the requirements of the EEC directive
2004/108/EC as amended by 92/31/EEC and 93/68/EEC Art.5 with
regard to “Electromagnetic compatibility”, and 2006/95/EC as amended
by 93/68/EEC Art.13 with regard to “Safety.”
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical
and Electronic Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment as
unsorted municipal waste, but use the return and collection systems
according to local law.
English
2

Quick start guide 3
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth. If still not clean, see “Cleaning the Display” in
this guide for further instructions.
7.
Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other devices (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade and
the third prong are provided for your safety. If the provided plug does not t
into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs. Convenience receptacles and the point where they exit from the
unit. Be sure that the power outlet is located near the unit so that it is easily
accessible.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied
by the manufacturer, or sold with the unit. When a cart is used,
use caution when moving the cart/unit combination to avoid
injury from tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when
the unit has been damaged in any way, such as: if the power-supply cord or
plug is damaged, if liquid is spilled onto or objects fall into the unit, if the
unit is exposed to rain or moisture, or if the unit does not operate normally
or has been dropped.
English

Quick start guide
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive
2002/95/EC of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS
Directive) and is deemed to comply with the maximum concentration values
issued by the European Technical Adaptation Committee (TAC) as shown below:
Substance Proposed Maximum
Concentration
Actual
Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers
(PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex of
the RoHS Directives as noted below:
Examples of exempted components are:
1. Mercury in compact uorescent lamps not exceeding 5 mg per lamp and in
other lamps not specically mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, uorescent tubes,
and electronic ceramic parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by
weight or more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight,
aluminium containing up to 0.4% lead by weight and as a cooper alloy
containing up to 4% lead by weight.
English
4

Quick start guide 5
English
Package contents
Check your Digital Photo Frame package for the following items.
• Digital Photo Frame
• Power adapter
• Stand
• Quick Start Guide
• USB cable
• Replacement front panel*
* The bundled front panel varies depending on the model you purchase.
Replacing front panel
If your Digital Photo Frame package contains a spare front panel, follow these
instructions to replace the front panel for personal preference.
1. Locate the indent on the edge
near the memory card socket.
2. Follow the direction of the gure
and gently lift the front panel.
3. To install a new front panel, align
the panel edge to the Digital
Photo Frame and gently place the
panel on the device.
1
2
3

Quick start guide
English
6
Connect
Button Function
OK Enter or conrm the selection
Left Move to the previous or left selection
Right Move to the next or right selection
Up Move upward
Down Move downward
Power On/Off
Locate control keys (in the back panel)
Locate the control buttons in the back panel according to the following
table.
2. Plug the power adapter from the device to a power outlet.
1. Align the head of the stand with the
socket, then rotate clockwise until the
stand locks into place.
Turn ON/OFF the device
Turn on the device
Press turn on the device, then the main
screen appears.
Turn off the device
Hold for 2 seconds then release to turn off
the device.
Tips: If you can’t turn on the device normally, please try to turn off the device
then turn it on again.

Quick start guide 7
English
Remote Control
Refer to the following image and table for details of the remote control.
No. Item Description No. Item Description
1 POWER Enable/disable Standby Mode 14 EXIT Go back one menu level
2 MUSIC Shortcut to the Audio menu 15 ROTATE Rotate photo 90° clockwise
3 VIDEO Shortcut to the Video menu 16 DOWN/NEXT Navigate down in menus/
skip to next available media
4 MUTE Mute audio output 17 FULL SCREEN Enlarge image to full screen
5 VOLUME UP Increase audio volume 18 LEFT/
REWIND
Navigate left in menus/
rewind audio playback
6 SOURCE Shortcut to Source menu 19 OK Select/accept selected item
7VOLUME
DOWN Decrease audio volume 20 View Display advanced media options in media menus
8 STOP Stop Video or Audio
playback 21 UP/PREV. Navigate up in menus/skip to previous available media
9 SLIDE SHOW Start slide show of available
photos 22 PLAY Play selected media
10 CALENDAR Show/hide Calendar in OSD 23 PAUSE Pause current media
11 MAIN MENU Display Main Menu 24 ZOOM IN Enlarge photo image size
12 RIGHT/
FORWARD
Navigate right in menus/fast
forward audio playback 25 ZOOM OUT Reduce photo image size
13 Setting Shortcut to Settings menu 26 PHOTO Shortcut to Photo menu
• ZOOM IN/OUT are only available using the remote control.
Setting
View
1 2 3 4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26

Quick start guide
English
8
Settings
Brightness
Allows you to adjust the screen brightness.
Language
Allows you to select the language you need.
Alarm Clock
Allows you to set the alarm time and turn on/off the alarm function.
Alarm Clock is disabled when the DPF is powered off.
Time and Date
Allows to set the time and date displayed in the OSD.
Show Calendar
Allows you to show/hide the calendar in the OSD.
Auto On/Off
Allows you to set the Auto On/Off schedule and enable or disable the Auto
On/Off function.
Auto On/Off only works on Standby mode.
Default
Go to SETTINGS > Default, then select Yes to retore to the factory default
setting or No to discard the selection.
Set Beep
Allows you to turn on/off the key control sound.
Status
Displays the software version and the current memory size.
Auto Tilt
Automatically adjusts the orientation of the screen when you rotate the frame.
The default value is On.
Auto Tilt does not compensate if the frame is placed upside
down—only 90° rotation clockwise or counter clockwise is
supported.
Volume
Allows you to adjust the volume between 0 and 16. The default value is 8.

Quick start guide 9
English
View Photos
From the main screen, press the Up and Down navigation keys to select
PHOTO, then select the photo source you want to display.
Photos pre-stored in the device will appear when no memory card or USB
ash disk is connected.
When photo source is selected, press OK to switch between 3 view modes:
• Browse mode: manual viewing of photos one-by-one
• Thumbnail mode: list of all photos
When viewing photos in Thumbnail mode, hold the Down navigation
key for 2 seconds then release to quickly enter the setting menu for
photo-related settings, or press View on the remote control.
• Slideshow mode: automatically shifting display of photos
To exit the PHOTO function, switch to Thumbnail mode, then press the Up
navigation key.
Compact Flash card
Memory Stick/ XD/
Secure Digital/ MMC card
(Right side)
USB ash disk
View photos from your memory card or USB ash
disk
1. Insert your memory card
with photos into the
corresponding slot,
OR: insert your USB
ash disk into the USB
port.
2. Photos on your memory
card will appear after a
few seconds.
Copy photos from your photo source
1. In Thumnail mode, press the navigation keys to select one photo.
2. Hold the Down navigation key for 2 seconds then release to quickly
enter the setting menu, or press View on the remote control.
3. Select Copy to or Copy all to, then press OK.
4. Select the source where you want to store the selected photos.
5. Press OK to copy.

Quick start guide
English
10
Copy multi-photos
1. In Thumnail mode, select one photo, then press the Down navigation
key . The selected photo is labeled with a "+" mark.
2. Repeat step 1 to other photos you want to copy to a source.
3. Finishing selection, repeat step 2–5 in section Copy photos from your
photo source.
Delete photos from your photo source
1. In Thumnail mode, press the navigation keys to select one photo.
2. Hold the Down navigation key for 2 seconds then release to quickly
enter the setting menu, or press View on the remote control.
3. Select Delete or Delete all, then press OK.
Delete multi-photos
1. In Thumnail mode, select one photo, then press the Down navigation
key . The selected photo is labeled with a "+" mark.
2. Repeat step 1 to other photos you want to delete.
3. Finishing selection, repeat step 2–3 in section Delete photos from your
photo source.
Photo Setting menu
While in Thumnail mode, hold the Down navigation key for 2 seconds
then release to enter the photo setting menu You can adjust the screen view,
slideshow sequence/effect/speed, copy or delete photos, effect, rotate photos,
and set background music from the photo setting menu.
• Full Screen: sets the displayed photo to full screen.
When set to Full Screen, the displayed photo is automatically cropped to
t the screen.
• Slideshow Sequence: sets the photo transition sequence.
• Slideshow Effect: sets the photo transition effect.
• Slideshow Speed: sets the photo transition frequency.
• Copy/Copy all to: copy one or all photos to a selected source.
• Delete/Delete all: delete one or all photos.
• Effect: displays photos in black and white.
• Rotate: rotate the displayed photo 0/90/180/270 degrees
• Background Music: display photos with background audio. Default value
is Off.
Photo and Audio les must be from the same Source, for example,
USB ash disk.