Vigor 2765 Series User manual

i
Vigor2765/2766 Series
VDSL2/G.Fast Security Router
Quick Start Guide
(Wireless models)
Guide Version: 1.3
Region: United Kingdom & Ireland
For updates and support, visit www.draytek.co.uk
August 2021 / Firmware V4.2.3_BT
Note: Product specification is subject to continuous evolution which may
not always be reflected in current documentation. For the formal specification
and details of the supported features of your product, please refer
only to the web site at www.draytek.co.uk
Regional and Network Compatibility
For all models, please check that you have been supplied with a device intended for your geographic region and networks.
Hardware and software varies by region, as well as local support and warranty services. To be sure of compatibility and local
support, ensure that you are buying the correct product through authorized channels. The outside of the product’s box will
state the region compatibility (e.g. “Applied Region: UK”). If you are unsure, check with DrayTek or your supplier. The use of
unofficial components (e.g. PSUs) or adapting interfaces or the use of unauthorized software/firmware may cause malfunction,
product damage or personal danger and invalidates your warranty and access to support services.

ii
Safety and Warranty Information
Safety
Instructions
Read the installation guide thoroughly before you set up the router.
The router is a complicated electronic unit that may be repaired only be authorized and qualified
personnel. Do not try to open or repair the router yourself.
Do not place the router in a damp or humid place, e.g. a bathroom.
Do not stack the routers.
The router should be used in a sheltered area, within a temperature range of 0 to +40 Celsius.
Do not expose the router to direct sunlight or other heat sources. The housing and electronic
components may be damaged by direct sunlight or heat sources.
Do not deploy the cable for LAN connection outdoor to prevent electronic shock hazards.
Keep the package out of reach of children.
When you want to dispose of the router, please follow local regulations on conservation of the
environment.
Warranty We warrant to the original end user (purchaser) that the router will be free from any defects in
workmanship or materials for a period of two (2) years from the date of purchase from a DrayTek
authorized dealer in the UK/Ireland. Please keep your purchase receipt in a safe place as it serves as proof
of date of purchase. During the warranty period, and upon proof of purchase, should the product have
indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or
replace the defective products or components, without charge for either parts or labour, to whatever
extent we deem necessary tore-store the product to proper operating condition. Any replacement will
consist of a new or re-manufactured functionally equivalent product of equal value, and will be offered
solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with,
damaged by external factors, used with unapproved accessories or subjected to abnormal working
conditions. Warranty applies to hardware only, not software or firmware. Defects which do not
significantly affect the usability of the product will not be covered by the warranty. We reserve the right
to revise the manual and online documentation and to make changes from time to time in the contents
hereof without obligation to notify any person of such revision or changes.
External Power Supply (Power Adapter) Information
1 2 3 4 5 6 7 8 9
A Manufacturer CWT CWT CWT CWT CWT APD APD APD APD
B Address No. 222, Sec.
2, Nankan
Rd., Lujhu
Township,
Taoyuan
County 338,
Taiwan
No. 222, Sec.
2, Nankan
Rd., Lujhu
Township,
Taoyuan
County 338,
Taiwan
No. 222, Sec.
2, Nankan
Rd., Lujhu
Township,
Taoyuan
County 338,
Taiwan
No. 222, Sec.
2, Nankan
Rd., Lujhu
Township,
Taoyuan
County 338,
Taiwan
No. 222, Sec.
2, Nankan
Rd., Lujhu
Township,
Taoyuan
County 338,
Taiwan
No.5, Lane 83,
Lung-Sou St.,
Taoyuan City
330, Taiwan
No.5, Lane 83,
Lung-Sou St.,
Taoyuan City
330, Taiwan
No.5, Lane 83,
Lung-Sou St.,
Taoyuan City
330, Taiwan
No.5, Lane 83,
Lung-Sou St.,
Taoyuan City
330, Taiwan
2ABB012F UK 2ABB018F UK 2ABL024F UK 2ABL030F UK 2ABN036F UK WA-12M12FG WB-18D12FG WA-24Q12FG WA-36A12FG C Model identifier 2ABB012F EU 2ABB018F EU 2ABL024F EU
2ABL030F EU 2ABN036F EU WA-12M12FK WB-18D12FK WA-24Q12FK WA-36A12FK
D Input voltage 100~240V 100~240V 100~240V 100~240V 100~240V 100~240V 100~240V 100~240V 100~240V
Input AC frequency 50/60Hz 50/60Hz 50/60Hz 50/60Hz 50/60Hz 50/60Hz 50/60Hz 50/60Hz 50/60HzE Output voltage DC 12.0V 12.0V 12.0V 12.0V 12.0V 12.0V 12.0V 12.0V 12.0V
F Output current 1.0A 1.5A 2.0A 2.5A 3.0A 1.0A 1.5A 2.0A 3.0A
G Output power 12.0W 18.0W 24.0W 30.0W 36.0W 12.0W 18.0W 24.0W 36.0W
H Average active
efficiency 84.9% 86.2% 87.6% 87.8% 89.8% 83.7% 85.4% 88.6% 88.2%
I Efficiency at low load
10% 73.6% 78.0% 81.3% 83.3% 83.7% 74.5% 80.5% 86.4% 85.4%
J No-load power
consumption 0.07W 0.07W 0.07W 0.07W 0.07W 0.07W 0.10W 0.07W 0.10W
For more updates & information, please visit www.draytek.co.uk. The external power supply used for each product will be
model dependent.
Join the UK mailing list Users in the UK & Ireland can sign up to our mailing list which goes out approximately 4
times per year with products news, updates, hints & tips and offers. For details, please visit
www.draytek.co.uk/list
Firmware & Tools Updates
Due to the continuous evolution of DrayTek technology and emerging risks, router firmware
updates may be issued.
Please consult the DrayTek web site for more information on newest firmware, tools and
documents: www.draytek.co.uk (For UK/Ireland)

iii
Declaration of Conformity
Hereby, DrayTek Corporation declares that the radio equipment type Vigor2765 is in compliance with
Regulation SI 2017 No. 1206.
The full text of the UKCA Declaration of Conformity is available at the following internet address:
https://www.draytek.com.tw/ftp/Vigor2765/Document/UKCA/
https://www.draytek.com.tw/ftp/Vigor2766/Document/UKCA/
Manufacturer: DrayTek Corp.
Address: No. 26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan
Product: Vigor2765/2766 Wireless Series
Importer: SEG, 11 Capital Business Park, Borehamwood, Herts, WD6 1GW
Frequency Information for UK area:
2.4G WLAN 2412MHz - 2472 MHz, max. TX power: 19.79dBm *1
5G WLAN 5160MHz - 5340 MHz, max. TX power: 22.74dBm *2
5480MHz - 5720 MHz, max. TX power: 29.88dBm
Requirements in UK. 5150MHz~5350MHz is for indoor use only.
(*1: for 2.4G WLAN model; *2: for 5G WLAN model)
This product is designed for DSL and 2.4GHz /5GHz WLAN network use in the UK & Ireland.
Declaration of Conformity
Hereby, DrayTek Corporation declares that the radio equipment type Vigor2765 is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://www.draytek.com.tw/ftp/Vigor2765/Document/CE/
http://www.draytek.com.tw/ftp/Vigor2766/Document/CE/
Manufacturer: DrayTek Corp.
Address: No. 26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan
Product: Vigor2765/2766 Wireless Series
Importer: SEG, 11 Capital Business Park, Borehamwood, Herts, WD6 1GW
Frequency Information for Europe area:
2.4G WLAN 2412MHz - 2472 MHz, max. TX power: 19.79dBm *1
5G WLAN 5160MHz - 5340 MHz, max. TX power: 22.74dBm *2
5480MHz - 5720 MHz, max. TX power: 29.88dBm
Requirements in AT/BE/BG/CZ/DZ/DK/EE/FR/DE/IS/IE/IT/EL/ES/
CY/LV/LI/LT/LU/HU/MT/NL/NO/PL/PT/RO/SI/SK/TR/FI/SE/CH/
HR. 5150MHz~5350MHz is for indoor use only.
(*1: for 2.4G WLAN model; *2: for 5G WLAN model)
This product is designed for DSL and 2.4GHz / 5GHz WLAN network throughout the EC region.

iv
T
Ta ab bl le e o of f C Co on nt te en nt ts s
1. Package Contents................................................................................................. 1
2. Panel Explanation................................................................................................. 2
2.1 Vigor2765ac/Vigor2766ac.......................................................................................................... 2
2.2 Vigor2765Vac/Vigor2766Vac...................................................................................................... 4
3. Hardware Installation ........................................................................................... 6
3.1 Connecting up the Vigor Router................................................................................................. 6
3.2 Wall-Mounting the Vigor 2765.................................................................................................... 7
4. Setup & Configuration.......................................................................................... 8
4.1 Accessing the Router Web Interface..........................................................................................8
4.2 WAN1 –ADSL & VDSL Connection Setup ...............................................................................11
4.2.1 PPPoE connection with FTTC VDSL2........................................................................ 11
4.2.2 DHCP / Static IP connection with FTTC VDSL2......................................................... 14
4.2.3 PPPoA connection with ADSL / ADSL2+.................................................................... 17
4.3 WAN2 – Ethernet Connection Setup........................................................................................ 18
4.3.1 Enabling the Ethernet WAN Port ................................................................................ 19
4.3.2 PPPoE......................................................................................................................... 20
4.3.3 Static or Dynamic IP.................................................................................................... 21
4.4 WAN3 / WAN4 – 3G / 4G USB Modem Setup......................................................................... 23
4.4.1 PPP Mode................................................................................................................... 23
4.4.2 DHCP Mode................................................................................................................25
5. Getting Further Help........................................................................................... 26
5.1 Additional Feature Setup.......................................................................................................... 26
5.2 Keep up to date with our mailing list ........................................................................................ 26
5.3 Firmware Updates.................................................................................................................... 27
5.4 Security & Router Best Practice............................................................................................... 27

1
1
1. . P Pa ac ck ka ag ge e C Co on nt te en nt ts s
DrayTek Vigor router Quick Start Guide
(This document)
RJ-45 Cable (Ethernet)
(Connects to your PC or Switch) RJ-11 to RJ-11 Cable (Connects to your DSL line)
UK Power Adapter Antenna
The maximum power consumption is 17-23 Watts.
Important
Note
Remove the protective film from the router before use to
ensure ventilation.

2
2
2. . P Pa an ne el l E Ex xp pl la an na at ti io on n
2
2. .1 1 V Vi ig go or r2 27 76 65 5a ac c/ /V Vi ig go or r2 27 76 66 6a ac c
LED Status Explanation
Blinking The router is ready and operating normally
(Activity) Off The router is powered off
On DSL connection synchronised
Blinking
(Slowly) DSL connection not currently synchronizing or not detected
(DSL)
Blinking
(Quickly) DSL connection is synchronising
On (Green) 2.4GHz Access Point is active
Blinking
(Green) Data is being transmitted on the router’s 2.4 GHz wireless interface
Blinking
(Orange) WPS pairing mode is active for two minutes
(Wireless LAN
On/Off/WPS)
Off 2.4GHz Access Point is turned off
On (Green) 5GHz Access Point is active
Blinking
(Green) Data is being transmitted on the router’s 5GHz wireless interface
(Wireless LAN
On/Off/WPS) Blinking
(Orange) WPS pairing mode is active for two minutes
On Ethernet LAN (RJ45) is connected
Blinking Data is transmitting (sending/receiving)
~
(LAN1/2/3/4)
Off Ethernet LAN is disconnected
On USB device is connected and ready for use
(USB) Blinking Data is being transmitted over USB

3
Interface Description
WLAN
ON/OFF/WPS Press for less than 2 seconds to switch toggle the router’s wireless interfaces:
For example,
2.4G (On) and 5G (On) – Default state.
2.4G (Off) and 5G (On) – press and release the button once.
2.4G (On) and 5G (Off) – press and release the button
twice.
2.4G (Off) and 5G (Off) – press and release the button
three times.
When WPS is enabled in the router’s web interface, press this
button for more than 2 seconds to enable WPS pairing mode.
Factory Reset Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press gently
and hold for more than 5 seconds. When the ACT LED blinks
rapidly, release the button. Then the router will restart with
the factory default configuration
USB1~USB2 Connector for a USB 3G/4G modem, storage, printer or USB
Thermometer
P1~P4 RJ-45 Gigabit Ethernet connectors for local network devices.
LAN port P4 can be configured as the Ethernet WAN port, see
Section 5.3 for details
DSL RJ-11 connector for ADSL or VDSL line
I/O Power Switch. Turns the unit on (I) or off (O)
PWR Connector for the power adapter

4
2
2. .2 2 V Vi ig go or r2 27 76 65 5V Va ac c/ /V Vi ig go or r2 27 76 66 6V Va ac c
LED Status Explanation
Blinking The router is ready and operating normally
(Activity) Off The router is powered off
On DSL connection synchronised
Blinking
(Slowly) DSL connection not currently synchronising or not detected
(DSL)
Blinking
(Quickly) DSL connection is synchronising
On The phone connected to this port is off-hook
Off The phone connected to this port is on-hook
Blinking A phone call is incoming
On (Green) 2.4GHz Access Point is active
Blinking
(Green) Data is being transmitted on the router’s 2.4 GHz wireless interface
Blinking
(Orange) WPS pairing mode is active for two minutes
(Wireless LAN
On/Off/WPS)
Off 2.4GHz Access Point is turned off
On (Green) 5GHz Access Point is active
Blinking
(Green) Data is being transmitted on the router’s 5GHz wireless interface
Blinking
(Orange) WPS pairing mode is active for two minutes
(Wireless LAN
On/Off/WPS)
Off 5GHz Access Point is turned off
On Ethernet LAN (RJ45) is connected
Blinking Data is transmitting (sending/receiving)
~
(LAN1/2/3/4)
Off Ethernet LAN is disconnected
On USB device is connected and ready for use
(USB) Blinking Data is being transmitted over USB

5
Interface Description
WLAN
ON/OFF/WPS Press for less than 2 seconds to switch toggle the router’s wireless interfaces:
For example,
2.4G (On) and 5G (On) – Default state.
2.4G (Off) and 5G (On) – press and release the button
once.
2.4G (On) and 5G (Off) – press and release the button
twice.
2.4G (Off) and 5G (Off) – press and release the button
three times.
When WPS is enabled in the router’s web interface, press
this button for more than 2 seconds to enable WPS pairing
mode.
Factory Reset Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press gently
and hold for more than 5 seconds. When the ACT LED blinks
rapidly, release the button. Then the router will restart with
the factory default configuration
USB1~USB2 Connector for a USB 3G/4G modem, storage, printer or USB
Thermometer
P1~P4 RJ-45 Gigabit Ethernet connectors for local network devices.
LAN port P4 can be configured as the Ethernet WAN port, see
Section 5.3 for details
DSL RJ-11 connector for ADSL or VDSL line
Phone2/Phone1 RJ-11 connectors for VoIP usage with analogue telephones
I/O Power Switch. Turns the unit on (I) or off (O)
PWR Connector for the power adapter

6
3
3. . H Ha ar rd dw wa ar re e I In ns st ta al ll la at ti io on n
3
3. .1 1 C Co on nn ne ec ct ti in ng g u up p t th he e V Vi ig go or r R Ro ou ut te er r
Here we take Vigor2765ac as an example.
1. ADSL/VDSL Connections: Connect the DSL port to the Modem or DSL port of the
external splitter/microfilter (not supplied) with the RJ-11 line cable. In some
cases, your RJ-11 DSL socket will be built-into your phone line socket on the wall
and you won’t have a separate microfilter/splitter.
2. LAN Connections: Connect a LAN port of the router to your computer or switch.
3. Wireless Antennas: Connect the wireless antennas to the router
4. Power Supply: Connect the power adapter to the Vigor 2765’s PWR socket on
the rear and plug the power adapter into a suitable mains socket.
Turn the Vigor 2765 on using its power switch.
5. The router will start up. After completing the system test, the ACT LED will light
up and start blinking once per second to indicate that it is ready for use.
For more detailed information of LED status, please refer to section 3.1 Front
Panel Overview.
6. Ethernet-based Internet Connections: LAN port P4 can be switched to operate
as the Ethernet WAN port. This must be configured in the router’s web interface
before it can operate in this mode – Section 5.3 of this Quick Start Guide details
how to do that.

7
3
3. .2 2 W Wa al ll l- -M Mo ou un nt ti in ng g t th he e V Vi ig go or r R Ro ou ut te er r
DrayTek Vigor 2765/2766 series routers have keyhole type mounting slots on the
underside to hang the router on, using screws attached to a wall or other
surface.
1. Drill two holes on the wall. The distance between the holes shall be 168mm.
2. Fit screws into the wall using the appropriate type of wall plug
3. With the screws installed, the router can be slotted into place
Note
The recommended drill diameter is 6.5mm (1/4”).

8
4
4. . S Se et tu up p & & C Co on nf fi ig gu ur ra at ti io on n
This section provides examples of how to initially access the router and configure
internet access for the most common types of Internet connection in the UK.
If the instructions in this quick start guide do not allow you to get online with
your ISP or type of Internet connection, there are additional guides available
from the Product Knowledgebase on www.draytek.co.uk.
Note To access the router, your PC will need to either get its IP
address using DHCP or have an IP address in the 192.168.1.x
range.
For details on how to change this, please refer to the “Trouble
Shooting” section in the User Guide.
4
4. .1 1 A Ac cc ce es ss si in ng g t th he e R Ro ou ut te er r W We eb b I In nt te er rf fa ac ce e
Open a web browser on your PC and type https://192.168.1.1.
The https:// prefix ensures that your connection is encrypted using SSL so that
your session data cannot be intercepted. Without that prefix, your data passes in
clear text.
You may get a warning from your browser (IE, Chrome, Edge, Safari etc.) about
your server (the router) having an invalid certificate. Your browser will demand
further confirmation or exception before allowing access. The warnings will look
something like these examples.
An example of how to access the router via HTTPS with Mozilla Firefox:

9
An example from Microsoft Edge, click “Continue to this webpage” to proceed:
Most other browsers will present equivalent warnings. In each case, following the
prompts/links will allow you to access the router's web interface. It is still
encrypted with SSL/TLS.
Note This warning appears because the router's default certificate is
'self-signed' rather than issued to you by a certificate authority
who has verified your identity.
A self-signed certificate means that you cannot verify the
identity of the server, but as it's your own local router, that
shouldn't be an issue - your connection is still encrypted.
The router login prompt will then request a username and password to allow
access. Here we take Vigor2765 as an example.
The factory default login details are:
Username: admin
Password: admin

10
Note If you cannot access the web interface, please go to the “Trouble
Shooting” section in the User Guide to determine the cause of
and solve your problem.
Upon successful login, the router will display the Dashboard, which shows a
summary of the router model, WAN status, front panel port status and other
information:
Note We recommend configuring a secure password when first logging
in to the router’s administration interface.
The router’s administration password can be changed from
[System Maintenance] > [Administrator Password]

11
4
4. .2 2 W WA AN N1 1 – – A AD DS SL L & & V VD DS SL L C Co on nn ne ec ct ti io on n S Se et tu up p
The WAN1 interface of the Vigor 2765 router can connect to VDSL2 / 35b and
ADSL2+ lines.
If your Internet connection uses VDSL2 and your ISP has supplied you with a
Username and Password to connect to the Internet, go to section
4.2.1 PPPoE connection with FTTC VDSL2
If your Internet connection uses VDSL2 and your ISP does not supply or require a
Username and Password to connect to the Internet, go to section
4.2.2 DHCP / Static IP connection with FTTC VDSL2
If your Internet connection uses ADSL or ADSL2+ and your ISP has supplied you
with a Username and Password to connect to the Internet, go to section
4.2.3 PPPoA connection with ADSL / ADSL2+
4
4. .2 2. .1 1 P PP PP Po oE E c co on nn ne ec ct ti io on n w wi it th h F FT TT TC C V VD DS SL L2 2
1. Go to [WAN] > [General Setup] and click on the WAN1 link:
2. On the settings page:
Set the Enable option to Yes to activate the WAN1 connection
Set the Active Mode to Always On
Enable the Service – VLAN Tag insertion
Set the Tag value setting to 101
DSL mode can be set to “VDSL2 only” but this is not required
Note The VLAN tag value of 101 is required to connect to ISPs that
operate on the Openreach VDSL2 network, if your ISP operates
on a different VDSL2 network, this tag value may differ.
Please check with your ISP or the DrayTek UK Knowledgebase for
ISP specific guides.

12
Click OK on that page to apply the changes.
3. Go to [WAN] > [Internet Access]
Set the WAN1 Access Mode to PPPoE / PPPoA, then click the Details Page
button to proceed:
4. On the PPPoE / PPPoA settings tab:
Select the Enable radio button at the top of the page to ensure that the PPPoE
interface is enabled.
In the ISP Access Setup section, input the ISP username into the Username field
and password in the Password field.
If your ISP has provided a static IP address, that can be specified by setting the
Fixed IP setting to Yes and entering the IP in the Fixed IP Address field.

13
Click OK on this page to apply the changes and the router will then prompt to
restart. Click the OK button to restart the router.
5. Once the router has restarted, the [Online Status] > [Physical Connection]
page will display the VDSL information and PPP connection status, if the
WAN1 section shows an IP address, it has connected to the internet
successfully:

14
Note If the WAN 1 IP address displayed begins with 172.16.x.x, it’s
possible that the ISP has not accepted the supplied Username
and Password for the Internet connection.
Check that the ISP Access Setup - Username and Password match
the details supplied by your ISP.
4
4. .2 2. .2 2 D DH HC CP P / / S St ta at ti ic c I IP P c co on nn ne ec ct ti io on n w wi it th h F FT TT TC C V VD DS SL L2
2
1. Go to [WAN] > [General Setup] and click on the WAN1 link:
2. On the settings page:
Set the Enable option to Yes to activate the WAN1 connection
Set the Active Mode to Always On
Enable the Service – VLAN Tag insertion
Set the Tag value setting to 101
DSL mode can be set to “VDSL2 only” but this is not required
Note The VLAN tag value of 101 is required to connect to ISPs that
operate on the Openreach VDSL2 network, if your ISP operates on
a different VDSL2 network, this tag value may differ.
Please check with your ISP or the DrayTek UK Knowledgebase for
ISP specific guides.

15
Click OK on that page to apply the changes.
3. Go to [WAN] > [Internet Access]
Set the WAN1 Access Mode to MPoA / Static or Dynamic IP, then click the
Details Page button to proceed:
4. In the MPoA / Static or Dynamic IP settings:
Select the Enable option and select Obtain an IP address automatically which
will obtain an IP from the ISP using DHCP.
If your ISP has provided a static IP range, with a Network address and a Subnet
Mask, specify that with the Specify an IP address option.

16
Click OK on this page to apply the changes and the router will then prompt to
restart. Click the OK button to restart the router.
5. Once the router has restarted, the [Online Status] > [Physical Connection]
page will display the VDSL information and DHCP connection status, if the
WAN1 section shows an IP address, it has connected to the internet
successfully: