Viking F20664B User manual

Viking Range Corporation
111 Front Street
Greenwood, Mississippi 3 930 USA
[phone]
For more product information,
call 1- -VIKING1 ( 45-4641) or
visit the Viking web site
vikingrange.com
F20664B EN (033011)
Built-In Electric Warming Dra ers
(Indoor and Outdoor Models)
Viking Installation Guide

Table of Contents
Warnings & Important Safety Instructions _______________________________________________3
Dimensions _________________________________________________________________________4
Specifications _______________________________________________________________________6
Cutout Dimensions (VEWD & DEWD) __________________________________________________7
Cutout Dimensions (DFWD)___________________________________________________________
Electrical Requirements ______________________________________________________________9
General Information ________________________________________________________________10
Installation (VEWD & DEWD)_________________________________________________________11
Custom Front (DFWD)_______________________________________________________________13
Final Preparation ___________________________________________________________________14
Performance Checklist ______________________________________________________________14
Service & Registration_______________________________________________________________15
IMPORTANT– Read and Follo !
Your safety and the safety of others is
ery important.
We have provided ma y importa t safety
messages i this ma ual a d o your
applia ce. Always read a d obey all
safety messages.
This is the safety alert symbol. This
symbol alerts you to hazards that
ca kill or hurt you a d others.
All safety messages will be preceded by
the safety alert symbol a d the word
“DANGER,” “WARNING” or “CAUTION.”
These words mea :
Hazards or unsafe practices
which WILL result in se ere personal
injury or death
DANGER
Hazards or unsafe practices
which COULD result in se ere personal
injury or death
Hazards or unsafe practices which
COULD result in minor personal injury or
property damage.
All safety messages will ide tify the
hazard, tell you how to reduce the cha ce
of i jury, a d tell you what ca happe if
the i structio s are ot followed.
WARNING
CAUTION
•Before beginning, please read these
instructions completely and carefully.
•DO NOT remove permanently affixed
labels, warnings, or plates from product.
This may void the warranty.
•All local and national codes and ordinances
must be observed. Installation must
conform with local codes, or in the absence
of codes, the National Electrical Code,
ANSI/NFPA70 - latest edition.
•The installer must leave these instructions
with the consumer who should retain for
local inspector’s use and for future
reference.
In Canada: Installation must be in accordance
with the current CSA C22.1 Canadian
Electrical Codes Part 1 and/or local codes.
WARNING
FIRE AND ELECTRICAL
SHOCK HAZARD
To reduce the risk of electric
shock a d fire, DO NOT use a
flexible power-supply cord with
this applia ce.
WARNING
For outdoor in tallation, in taller mu t
in tall a ground fault interrupt.
WARNING
Make sure that i comi g voltage is the
same as u it rati g. A electric rati g plate
specifyi g voltage, hertz, wattage, amps,
a d phase is attached to the product.
Wiri g the warmi g drawer with more
voltage tha it is rated for may cause
severe damage to the thermostat,
eleme t, a d other compo e ts. Wiri g
the warmi g drawer with less voltage tha
it is rated for may cause sig ifica t
decrease i performa ce.
WARNING
To reduce the risk of fire, electric shock, or
i jury to perso s, i stallatio work a d
electrical wiri g must be do e by qualified
people i accorda ce with all applicable
codes a d sta dards, i cludi g fire-rated
co ditio s.
23

Dimensions - VEWD
4
Dimensions - DEWD & DFWD
5
23-1/4”
(59.1 cm)
27-3/4”
(70.5 cm)
8-31/32”
(22.8 cm)
10”
(25.4 cm)
A
23-1/4”
(59.1 cm)
27-7/16”
(69.7 cm)
8-31/32”
(22.4 cm)
10”
(25.4 cm)
A
27-3/4”
(70.5 cm)
26-3/4”
(67.9 cm)
23-1/4”
(59.1 cm)
1-3/8”
(3.5 cm)
23-1/4”
(59.1 cm)
10-1/2”
(26.7 cm)
8-31/32”
(22.8 cm)
A
27-7/16”
(69.7 cm)
23-7/16”
(59.5 cm)
1-5/8”
(4.1 cm)
22-15/16”
(58.3 cm)
23-1/4”
(58.7 cm)
23-1/4”
(58.7 cm)
Custom
VEWD527/530/536 Designer
DEWD102
Custom Front
DFWD171/101
DEWD102
Overall
width A
29-1/2”
(74.9 cm)
DFWD171 DFWD101
Overall
width A
26”
(66.0 cm)
29”
(73.7 cm)
VEWD527 VEWD530 VEWD536
Overall
width A
26-1/2”
(67.3 cm)
29-1/2”
(74.9 cm)
35-1/4”
( 9.5 cm)
23-1/4”
(59.1 cm)
26-3/4”
(67.9 cm)
8-31/32”
(22.8 cm)
10”
(25.4 cm)
A
26-3/4”
(67.9 cm)
23-1/4”
(59.1 cm)
1-3/8”
(3.5 cm)
25-3/4”
(65.4 cm)
Professional
VEWD173T/103T/163T
VEWD173T VEWD103T VEWD163T
Overall
width A
26-1/2”
(67.3 cm)
29-1/2”
(74.9 cm)
35-1/4”
( 9.5 cm)

Cutout Dimensions - VEWD & DEWD
7
A
C
B
VEWD527 VEWD530 VEWD536 DEWD102
Cutout width (A) 25-1/4” (64.1 cm) 2 -1/4” (71. cm) 34” ( 6.4 cm) 2 -1/4” (71. cm)
Cutout depth (B) 23-1/2” (59.7 cm) 23-1/2” (59.7 cm) 23-1/2” (59.7 cm) 23-1/2” (59.7 cm)
Cutout height (C) 9-1/4” (23.5 cm) 9-1/4” (23.5 cm) 9-1/4” (23.5 cm) 9-1/4” (23.5 cm)
VEWD173T VEWD103T VEWD163T
Cutout width (A) 25-1/4” (64.1 cm) 2 -1/4” (71. cm) 34” ( 6.4 cm)
Cutout depth (B) 23-1/2” (59.7 cm) 23-1/2” (59.7 cm) 23-1/2” (59.7 cm)
Cutout height (C) 9-1/4” (23.5 cm) 9-1/4” (23.5 cm) 9-1/4” (23.5 cm)
C
B
A
2” min.
(5.1 cm)
Outdoor
Indoor
Note: For Outdoor Models, seal around drawer opening with silicon caulk that is pro ided.
Specifications
6
Flus Mount Option:
Note: To install the warming drawer in a flush mount application, a flush mount
accessory kit is required and sold separately.
VEWD527 VEWD530 VEWD536 DEWD102
Cutout width (A) 26-15/16” (6 .4 cm)29-15/16” (76.0 cm) 35-15/16” (91.3 cm) 29-5/ ” (75.3 cm)
Cutout depth (B) 25-3/ ” (64.5 cm) 25-3/ ” (64.5 cm) 25-3/ ” (64.5 cm) 25-1/ ” (63. cm)
Cutout height (C) 10-5/ ” (27.0 cm) 10-5/ ” (27.0 cm) 10-5/ ” (27.0 cm) 10-1/ ” (25.7 cm)
Description VEWD527 VEWD530 VEWD536 VEWD173T VEWD103T VEWD163T DEWD102 DFWD171 DFWD101
Overall width 26-1/2”
(67.3 cm)
29-1/2”
(74.9 cm)
35-1/4”
( 9.5 cm)
26-1/2”
(67.3 cm)
29-1/2”
(74.9 cm)
35-1/4”
( 9.5 cm)
29-1/2”
(74.9 cm)
26”
(66.0 cm)
29”
(73.7 cm)
Overall height
(from bottom) 10” (25.4 cm) 10-1/2” (26.7 cm)
Overall depth (from rear)
To end of handle
With drawer fully
extended
27-3/4”(70.5 cm)
51-3/ ” (130.5 cm)
26-3/4”(67.9 cm)
50-3/ ” (12 .0 cm)
27-7/16”
(69.7 cm)
4 ”
(121.9 cm)
N/A N/A
Interior width 17-1/4”
(43. cm)
20-1/2”
(52.1 cm)
25”
(63.5 cm)
17-1/4”
(43. cm)
20-1/2”
(52.1 cm)
25”
(63.5 cm)
20-1/2”
(52.1 cm)
17-1/4”
(43. cm)
20-1/2”
(52.1 cm)
Interior height 6” (15.2 cm)
Interior depth 22-3/4” (27. cm)
Electrical
Requirements
Hard wire direct with separate 15 amp minimum 2-wire with ground circuit;
120 VAC/50-60 Hz
Max. Amp Usage 425 watts
3.6 amps
450 watts
3. amps
550 watts
4.6 amps
425 watts
3.6 amps
450 watts
3. amps
550 watts
4.6 amps
450 watts
3. amps
425 watts
3.6 amps
450 watts
3. amps
Approx. shipping wt. 0 lb.
(36 kg)
90 lb.
(40.5 kg)
110 lb.
(49.5 kg)
0 lb.
(36 kg)
90 lb.
(40.5 kg)
110 lb.
(49.5 kg)
90 lb.
(40.5 kg)
110 lb.
(49.5 kg)
Rear View
VEWD/DEWD/DFWD
C
2”
(5.1 cm)
8-31/32”
(22.8 cm)
2” (5.1 cm)
120V Electrical Opening
(When facing cabinet, opening is
located on right side.)
VEWD527/
173T DFWD171
VEWD530/103T
DEWD102 DFWD101
VEWD536/
163T
Overall
width C
24-7/ ”
(63.2 cm)
24-7/ ”
(63.2 cm)
27-7/ ”
(70. cm)
27-7/ ”
(70. cm)
33-5/ ”
( 5.4 cm)
Dimensions

Electrical Requirements
WARNING
Electrical shock hazard.
To avoid the risk of electrical
shock, perso al i jury or death;
verify electrical power is tur ed
off at the breaker box u til the ra ge is
i stalled a d ready to operate, i stallatio
by a authorized i staller o ly.
9
Electrical Connection
VEWD527/
173T,
DFWD171
VEWD530/
103T,
DEWD102
DFWD101
VEWD536/
163T
Max. amp
usage
425 watts
3.6 amps
450 watts
3. amps
550 watts
4.6 amps
Electrical Requirements
Check your national and local codes
regarding this unit. Hard wire direct with
seperate 120V/15 amp minimum 2-wire
wtih ground circuit. Maximum amp usage.
Note: Use copper conductors ONLY!
Grounding Instructions
This appliance must be connected to a
grounded metal, permanent wiring system,
or an equipment-grounding conductor
must be run with the circuit conductors and
connected to the equipment-grounding
terminal or lead on the appliance.
With the appliance positioned in front of
the cabinet opening, connect wire leads
extending from the power supply to the
terminal block of the unit. Make sure the
colored wires of the terminal block are
connected to the corresponding colored
wires extending from the power supply.
Cutout Dimensions - DFWD
DFWD171 DFWD101
Cutout width (A) 25-1/4” (64.1 cm) 2 -1/4” (71. cm)
Cutout depth (B) 24” (61.0 cm) 24” (61.0 cm)
Cutout height (C) 9-1/4” (23.5 cm) 9-1/4” (23.5 cm)
A
C
B
Custom Front Models

Installation - VEWD & DEWD
11
1
2
1
2
Pull out warming drawer
pan until fully extended.
Slide finger along right and left side until you reach the
black hand latches (located at the front of the rails). Pull
up on both the right and left latches and pull out
drawer pan support.
3
Outdoor onlyOutdoor onlyOutdoor only
2”
(5.1 cm)
2”
(5.1 cm)
Electrical opening
(from rear)
4
Apply silicone caulk around the back
of the warming drawer trim.
Note: For outdoor models ONLY.
2
1
1
5
Feed supply cord up through
hole in rear of warming drawer.
Remove strain relief bracket and mounting
screws on the terminals.
1
2
6
Attach the white (neutral) and black (line) lead
terminals. Attach ground wire to the
center terminal.
General Information
10
• When installing this unit directly below
other units, only install with Viking built-
in products.
•Remove warming drawer carefully from
carton. Remove all loose packaging and
accessories.
• It is the responsibility of the installer to
comply with local codes. If no local
codes are applicable, wire in accordance
with the National Electrical Code,
ANSI/NFPA 70 - latest edition.
•T is appliance is not fused. Protect
wit a proper sized fuse or circuit
breaker and a GFI for outdoor models.
• Line disconnect switch, circuit breaker,
GFI (for outdoor models) or
plug/receptacle of power cord
connection should be readily accessible
to the operator.
• Ground unit per applicable electrical
codes.
• Any installation not matching the
specifications discussed in these
instructions will void the manufacturer’s
warranty.
READ AND FOLLOW ALL WARNING
AND CAUTION INFORMATION
WHEN INSTALLING THIS APPLIANCE.
Moving, Handling and Unpacking
Remove and discard all packing materials,
including cardboard and tape on the
outside and inside of the warming drawer.
Some stainless steel parts may have a
plastic protective wrap which must be
peeled off. The interior should be washed
thoroughly with hot, soapy water to remove
film residues and any dust or debris before
being used, then rinsed and wiped dry.
Solutions stronger than soap and water are
rarely needed.

12
1
2
7
Push supply cord toward terminal
block to relieve strain, reattach supply cord strain relief
bracket over supply cord.
8
9
x4
Slide cavity assembly into the cabinet opening.
Secure the warming drawer using four
# mounting screws (four screws provided).
10
Replace drawer assembly.
Installation - Custom Front DFWD
13
1
2
1
2
Pull out warming drawer pan until fully extended. Slide finger along right and left side until you reach the
black hand latches (located at the front of the rails). Pull
up on both the right and left latches and pull out
drawer pan support.
Inside Drawer
Custom Front
Panel
3
id
d
C
to
ne
e
r
Center the custom front on the inside drawer panel.
Attach the custom front with the six 5/ ” screws provided.

Final Preparation
14
Service & Registration
15
• All stainless steel body parts should be
wiped with hot, soapy water and with a
liquid cleaner designed for this material.
If buildup occurs, DO NOT use steel wool,
abrasive cloths, cleansers, or powders!
If it is necessary to scrape stainless steel
to remove encrusted materials, soak with
hot, wet cloths to loosen the material, then
use a wool or nylon scraper. DO NOT use
a metal knife, spatula, or any other
material tool to scrape stainless steel!
Scratches are almost impossible to
remove.
Only authorized replacement parts may be used in performing service on the appliance.
All servicing should be referred to a qualified technician.
Contact Viking Range Corporation, 1- -VIKING1 ( 45-4641), for the nearest service parts
distributor in your area or write to:
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
Warming Drawer – The serial number and model number for your
appliance can be found by pulling drawer out until it stops and lifting
inner lining. Rating/Serial plate is located on the left, rear side.
Record the following information indicated below. You will need it if service is ever required.
Model number ____________________________________________________________________________________
Serial number _____________________________________________________________________________________
Date of purchase __________________________________________________________________________________
Date installed ______________________________________________________________________________________
Dealer's name _____________________________________________________________________________________
Address ___________________________________________________________________________________________
T ese installation instructions s ould remain wit t e unit for future reference.