Vingtor Stentofon TCIV-2 Instruction sheet

Configuration Manual
Turbine Compact IP Video Stations
TCIV-2
TCIV-3
TCIV-6
A100K11559
TECHNICAL MANUAL

About this Document
Document Scope
This document describes the setup procedure and conguration of the various models of the Turbine
Compact IP Video station series.
Station Firmware Version: VSF-Turbine 4.7
Product Item Number
Tubine Compact IP Video Station - TCIV-2 1008115020
Tubine Compact IP Video Station - TCIV-3 1008115030
Tubine Compact IP Video Station - TCIV-6 1008115060
Publication Log
Rev. Date Author Status Comments
1.0 21.12.2015 HKL Published
1.1 9.5.2016 HKL Published Same IP for camera & station
1.2 20.6.2016 HKL Published New screenshots IP Desktop
1.3 22.8.2016 HKL Published Pulse and SIP for IP Desktop
1.4 27.9.2017 HKL Published ITSV-1, SW 4.7
Related Documentation
For further information, refer to the following documentation:
Doc. number Documentation
A100K11194 Turbine IP Stations Technical Manual
A100K11625 Turbine Compact IP Video Station Mounting Guide
A100K11293 Turbine Compact IP Station Getting Started for Alphacom
A100K11335 Turbine Compact IP Station Getting Started for SIP
A100K11336 Turbine Compact IP Station Getting Started for Pulse
A100K11664 IP Desktop Station with Video Display Manual
A100K11619 VS-IMT User Manual
A100K11705 ITSV-1 Video Phone Quick Installation Guide

3
Turbine IP Video Station Conguration Guide
A100K11559
Contents
1 Turbine Compact IP Video Stations ............................................................................................. 5
2 Station Connections...................................................................................................................... 7
2.1 External Connectors on IP Video Station................................................................................ 7
2.2 Power Supply.......................................................................................................................... 7
2.3 Network Connection................................................................................................................ 7
2.4 Input/Output Connections ....................................................................................................... 7
3 Starting Up the Video Station ....................................................................................................... 8
4 Turbine Video Settings .................................................................................................................. 9
5 AlphaComConguration ............................................................................................................ 10
5.1 Logging into the Station ........................................................................................................ 10
5.2 Station Main Settings .............................................................................................................11
5.3 AlphaCom Conguration for ITSV-1 Video Phone ................................................................ 12
5.3.1 Video Settings for ITSV-1............................................................................................ 12
5.3.2 ITSV-1 Phone Settings................................................................................................ 13
5.3.3 ITSV-1 Account Setup................................................................................................. 13
5.3.4 ITSV-1 Audio Codec Settings...................................................................................... 14
5.3.5 ITSV-1 Video Conguration......................................................................................... 14
5.4 AlphaCom Conguration for VS Desktop Video Display Station........................................... 15
5.4.1 Video Settings for Desktop Station ............................................................................ 15
5.4.2 VS Desktop Station Video Conguration .................................................................... 16
6 SIPConguration......................................................................................................................... 18
6.1 Logging into the Station ........................................................................................................ 18
6.2 Station Main Settings ........................................................................................................... 19
6.3 SIP Conguration for ITSV-1 Video Phone ........................................................................... 20
6.3.1 SIP Settings for ITSV-1 ............................................................................................... 20
6.3.2 Video Settings for ITSV-1............................................................................................ 21
6.3.3 ITSV-1 Phone Settings................................................................................................ 21
6.3.4 ITSV-1 Account Setup................................................................................................. 22
6.3.5 ITSV-1 Video Conguration......................................................................................... 22
6.4 SIP Conguration for Cisco Video Phone ............................................................................. 23
6.4.1 SIP Settings ................................................................................................................ 23
6.4.2 Video Settings for Cisco Phone .................................................................................. 24
6.4.3 Direct Access Key Settings ......................................................................................... 25
6.5 SIP Conguration for Bria Softphone.................................................................................... 26
6.5.1 Video Settings for Bria Softphone............................................................................... 27
6.5.2 Direct Access Key Settings ......................................................................................... 28
6.5.3 Bria Softphone Settings .............................................................................................. 28
6.6 SIP Conguration for VS Desktop Video Display Station...................................................... 30
6.6.1 SIP Settings ................................................................................................................ 30
6.6.2 Video Settings for Desktop Video Display Station ...................................................... 31
6.6.3 Desktop Video Display Station Settings...................................................................... 31
7 PulseConguration..................................................................................................................... 34
7.1 Logging into the Station ........................................................................................................ 34
7.2 Station Main Settings ........................................................................................................... 35
7.3 Pulse Conguration for ITSV-1 Video Phone........................................................................ 36
7.3.1 SIP Settings ................................................................................................................ 36
7.3.2 Third Party SIP Terminals ........................................................................................... 36
7.3.3 Video Settings for ITSV-1............................................................................................ 37
7.3.4 Direct Access Key Settings ......................................................................................... 37
7.3.5 ITSV-1 Phone Settings................................................................................................ 38
7.3.5.1 ITSV-1 Account Setup.......................................................................................... 38
7.3.5.2 ITSV-1 Video Conguration ................................................................................. 39
7.3.6 Verifying Registration of ITSV-1 .................................................................................. 39
7.4 Pulse Conguration for Bria Softphone................................................................................. 40
7.4.1 SIP Settings ................................................................................................................ 40
7.4.2 Video Settings for Bria Softphone............................................................................... 40
7.4.3 Direct Access Key Settings ......................................................................................... 41
7.4.4 Third-Party SIP Terminals ........................................................................................... 41
7.4.5 Bria Softphone Conguration...................................................................................... 42
7.4.6 Verifying Registration of Bria Softphone ..................................................................... 43
7.5 Pulse Conguration for Snom Video Phone.......................................................................... 43
7.5.1 SIP Settings ................................................................................................................ 43
7.5.2 Video Settings for Snom Phone.................................................................................. 44
7.5.3 Direct Access Key Settings ......................................................................................... 45

4
A100K11559
Turbine IP Video Station Conguration Guide
7.5.4 Third Party SIP Terminals ........................................................................................... 45
7.5.5 Snom Phone Settings ................................................................................................. 46
7.5.6 Verifying Registration of Snom Video Phone .............................................................. 47
7.6 Pulse Conguration for VS Desktop Video Display Station .................................................. 47
7.6.1 SIP Settings ................................................................................................................ 47
7.6.2 Video Settings for Desktop Video Display Station ...................................................... 48
7.6.3 Direct Access Key Settings ......................................................................................... 49
7.6.4 Desktop Video Display Station Settings...................................................................... 49
8 Station Indication LEDs .............................................................................................................. 52
8.1 LEDs on Front Plate.............................................................................................................. 52
9 Restoring Factory Defaults......................................................................................................... 53
9.1 Reset to Factory Default Settings with Activated DHCP ....................................................... 53
9.2 Reset to Factory Default Settings with Static IP.................................................................... 53
10 Camera Field of View................................................................................................................... 54
Figures
Figure 1 Turbine TCIV-2 / TCIV-3 Station Keys & Functions .............................................................. 5
Figure 2 Turbine TCIV-6 Station Keys & Functions ............................................................................ 6
Figure 3 External Connectors on IP Station........................................................................................ 7
Figure 4 Turbine Video AlphaCom/Pulse/SIP System ........................................................................ 8
Figure 5 AlphaCom Video Intercom System..................................................................................... 10
Figure 6 SIP Video Intercom System................................................................................................ 18
Figure 7 Pulse Video Intercom System............................................................................................. 34

5
Turbine IP Video Station Conguration Guide
A100K11559
1 Turbine Compact IP Video Stations
All IP Video stations in the Turbine Compact series o󰀨ers audio features such as: HD voice quality,
Open Duplex, Active Noise Cancellation, MEMS microphone, a 10W Class D amplier and our
unique speaker grille design. The Video camera features wide FoV HD Video, Digital PTZ, and
support for H.264 or MJPEG.
There are three station models in the Turbine Compact IP Video series:
TCIV-2
Stainless steel frontplate with single call button
TCIV-3
Thermoplastic frontplate with single call button
TCIV-6
Thermoplastic frontplate with call & scrolling
buttons and PMOLED display
Figure 1 Turbine TCIV-2 / TCIV-3 Station Keys & Functions
Speaker
Microphone
Call Button
Camera
Lens

6
A100K11559
Turbine IP Video Station Conguration Guide
Figure 2 Turbine TCIV-6 Station Keys & Functions
Speaker
Cancel
Microphone
Call Button
Scroll Up
Scroll Down
PMOLED
Display
Camera
Lens

7
Turbine IP Video Station Conguration Guide
A100K11559
2 Station Connections
2.1 External Connectors on IP Video Station
Figure 3 External Connectors on IP Station
The following table is an overview of the main connectors involved when installing the Turbine IP
Stations.
Ethernet / Power 10/100 Mbps Ethernet RJ-45 port for LAN (uplink) connection. Supports PoE
(802.3af). Draws power from either spare line or signal line.
Secondary Power 24 VDC (16 – 48 V) secondary power is provided from an external adapter.
Relays There is one Double Throw relay contact with 60W switching power. COM, NO,
NC contacts are provided. Max: 250VAC/220VDC, 2A, 60W.
Input/Output 6 general purpose I/Os are available. Each I/O can be congured as either
button input or LED driver.
Audio Line Out A balanced 600 ohm audio line out with induction loop signal
2.2 Power Supply
The Turbine Station supports Power over Ethernet (PoE, IEEE 802.3 a-f) where power can be drawn
from either the spare line or signal line.
If PoE is not available, the Turbine Station can be connected to a 24 VDC local power supply.
2.3 Network Connection
There is one RJ-45 port located on the Turbine station that is used as the PoE/LAN port.
2.4 Input/Output Connections
There are 6 I/O connection options for the Turbine Station.
These connections are used as relay contacts for door lock control and external I/O devices.
1
5
4
3
2
1
6
10
5
4
3
2
9
8
7
RJ-45
PoE
port
24 VDC for external secondary power
if PoE is not used. Pin 1 is positive.
- 5.3V (LED driver)
- GND
- Input/Output 5
- COM relay
- NC relay
- NO relay
- Input/Output 1
- Input/Output 2
- Input/Output 3
- Input/Output 6
- 600 ohm balanced line out +
- 600 ohm balanced line out -
- Input/Output 4
Ethernet Connection
PoE port

8
A100K11559
Turbine IP Video Station Conguration Guide
3 Starting Up the Video Station
The Turbine Video Station features an embedded web interface, which allows users to log in via a
standard web browser.
LSoftware upgrade procedure for the video station is the same as for the audio stations in the
Turbine series. For further details, see A100K11194 Turbine IP Stations Technical Manual.
To start up the station, your PC and the IP station have to be connected together via a PoE switch
using network cables:
1. Connect the PC to the PoE switch
2. Connect the PoE port on the IP station to the PoE switch
When the Turbine Video Station is connected to the network, the IP address of the station is
automatically obtained in one of two ways:
1. An IP address is obtained from a DHCP server if there is one.
2. If there is no DHCP server, an IP address in the range 169.254.x.x will be assigned.
To make the station speak its IP address:
●Press the call button on the station
- when the station is not registered yet
At commissioning, the IP Video station needs to be congured to enable it to be used as:
● Station subscribed to an AlphaCom server
●SIP station
● Pulse station
Figure 4 Turbine Video AlphaCom/Pulse/SIP System
AlphaCom XE Server/Exchange
AlphaComXE7
Turbine TCIV-2
Turbine TCIV-6
Desktop Video Display Station
Turbine TCIV-3
iPBX (SIP domain)
SIP Video Phone
ITSV-1 Video Phone
IP Network

9
Turbine IP Video Station Conguration Guide
A100K11559
4 Turbine Video Settings
After logging into the station via the web interface:
● Select menu option Video Settings
The parameters for video settings are as shown below:
Video Mode
This parameter denes whether the video stream will be in either of the two modes: MJPG in http or
H.264 in RTP.
Enable Video
This parameter denes whether calls made from the station will be video calls.
Camera IP address and port
This is the IP address and port number of the camera streaming the video to a web browser or video
display station. The video camera and the Turbine station have the same IP address.
Lens distortion correction
Enabling this parameter will correct the “sh eye” e󰀨ect that can occur on the edges of the video
image.
Night Mode
Enabling this parameter will make it possible for the camera to record in low-light conditions.
Zoom
This parameter sets the digital zoom of the video image. The zoom level range is 1.0 to 2.5. Once
it is set higher than 1.0 it allows for o󰀨setting the view horizontally and vertically. The o󰀨set range is
-100 to 100.
Color saturation
This parameter sets the color saturation of the video image. The range is 0 to 255. Default value is
128.
Contrast
This parameter sets the contrast of the video image. The range is 0 to 255. Default value is 128.
Brightness
This parameter sets the brightness of the video image. The range is 0 to 255. Default value is 128.
Backlight compensation
This parameter sets the backlight compensation for the video image. The range is from 0 to 5. The
default value is 2.

10
A100K11559
Turbine IP Video Station Conguration Guide
5 AlphaComConguration
The Turbine Video Stations are connected to the AlphaCom XE server/exchange. The AlphaCom
XE server/exchange includes all main service congurations for the IP stations and only a minimum
conguration is needed to be carried out on the actual station.
In AlphaCom mode, the Turbine Video stations are used together with:
● IP Desktop Station with Video Display (Item Number: 1408001635)
● ITSV-1 Video Phone (Item Number: 1490001010)
LCongurationofthenon-videopartofthestationsuchasaudioandI/Osettingsisdescribedinthe
manual: A100K11293 Turbine Compact IP Station Getting Started for AlphaCom.
Figure 5 AlphaCom Video Intercom System
5.1 Logging into the Station
Access the station by logging into the web interface using a standard web browser:
1. Open a web browser
2. In the browser’s address bar, type the station IP address and press the ENTER key
- The station login page will be displayed.
To log into the station:
1. Click Login
2. Enter the default User name: admin
3. Enter the default password: alphaadmin
The Station Information page will now be displayed, showing the IP station conguration and
status.
AlphaCom XE Server/Exchange
AlphaComXE7
Turbine TCIV-2
Turbine TCIV-6
IP Desktop Station with Video Display
Turbine TCIV-3
ITSV-1 Video Phone
IP Network

11
Turbine IP Video Station Conguration Guide
A100K11559
5.2 Station Main Settings
● Click Station Main > Main Settings to access the page for conguring station mode and IP
parameters.
Station Mode
● Select the Use Alphacom radio-button
Product Model And Accessory
●Model
Select one of the options from the drop-down box :
-VideoNormal(TCIV-2,TCIV-3)
-VideoScrollingStation(TCIV-6)
Registration Settings
●AlphaComIP-address
- Enter IP address of AlphaCom in which TCIV is to be registered as a subscriber
●Directory Number
- Enter the directory number of TCIV (e.g. 2222)
IP Settings
●Static IP – Select this option if the IP station shall use a static IP address. Enter values for:
-IP-address:IPaddressof TCIV (e.g. 10.5.101.46)
-Subnet-mask:Entersubnetmask
-Gateway: Enter Gateway IP address
-DNS Server 1 (option for network administration)
-DNS Server 2 (option for network administration)
-Hostname (option for network administration)
Read IP Address
● Check the Read IP Address box to enable an unregistered station to speak its IP address
when the call button is pressed.
● Click Save followed by Apply to apply the new conguration settings.

12
A100K11559
Turbine IP Video Station Conguration Guide
5.3 AlphaComCongurationforITSV-1VideoPhone
● Vingtor-Stentofon ITSV-1 Video Phone - item no. 1490001010
5.3.1 VideoSettingsforITSV-1
To congure video settings:
● Select Advanced Alphacom > Video
● Select or set values for the parameters:
Enable Video: Check box to enable video calls
Resolution: Select 480P
Frames per second: Select 15fps
Camera IP address and port: Enter the port number - default is 8090
Video setup mode: Select Default
LThe video camera and the Turbine station have the same IP address.
- The video stream from the camera can be viewed by entering the IP address and port
number in a web browser, e.g. 10.5.101.46:8090
LVideo calls in the AlphaCom system are made in MJPG mode only.
LThe same IP address (e.g. 10.5.101.46) and port number (e.g. 8090) set here must be entered into
the Camera Settings of the ITSV-1.
● Click Save
● Click Backtocongpage

13
Turbine IP Video Station Conguration Guide
A100K11559
5.3.2 ITSV-1PhoneSettings
● Log into the ITSV-1 phone interface by entering its IP address in a browser on your PC
Login Credentials
Username: admin
Password: alphaadmin
5.3.3 ITSV-1AccountSetup
● Select Account >Account 1 >General Settings
● Enter the values shown above for the parameters
Account Active: Check Yes box
SIP Server: IP address of AlphaCom server (see Main Settings in TCIV)
SIP User ID: Directory Number of ITSV-1 phone
SIP Authentication ID: Same as SIP User ID

14
A100K11559
Turbine IP Video Station Conguration Guide
5.3.4 ITSV-1AudioCodecSettings
● Check in AlphaPro under Users & Stations the codec that has been selected for the SIP
phone (normally G722)
● Select Account 1 >Codec Settings
● Remove all codecs from the Selected list except the one dened in AlphaPro, i.e. G722.
5.3.5 ITSV-1VideoConguration
The video is streamed in MJPEG format directly from the TCIV camera to the ITSV-1. The AlphaCom
server is not involved in the video stream. The TCIV camera must have a static IP address.
● Select Account 1 > Call Settings
● Click the Yes box for Start Video Automatically
● Select Vingtor Stentofon System from Special Feature dropdown box
● Click Congure to open the camera list

15
Turbine IP Video Station Conguration Guide
A100K11559
● Enter the camera URL and the directory number of the TCIV station
Door System URL : http://< TCIV camera IP address>:<port no.>/mjpg/video.mjpg
Example: http://10.5.101.46:8090/mjpg/video.mjpg
Door System SIP User ID : Directory Number of TCIV station
5.4 AlphaComCongurationforVSDesktopVideoDisplayStation
● Vingtor-Stentofon IP Desktop Video Station - item no. 1408001635
5.4.1 Video Settings for Desktop Station
To congure video settings:
● Select Advanced Alphacom > Video
● Select or set values for the parameters:
Enable Video: Check box to enable video calls
Resolution: Select 240P
Frames per second: Select 15fps
Camera IP address and port: Enter the port number - default is 8090
Video setup mode: Select Default

16
A100K11559
Turbine IP Video Station Conguration Guide
LThe video camera and the Turbine station have the same IP address.
- The video stream from the camera can be viewed by entering the IP address and port
number in a web browser, e.g. 10.5.101.46:8090
LVideo calls in the AlphaCom system are made in MJPG mode only.
LThe same IP address (e.g. 10.5.101.46) and port number (e.g. 8090) set here must be entered into the
Camera Settings described in section “5.4.2 VS Desktop Station Video Conguration”.
● Click Save
● Click Backtocongpage
5.4.2 VSDesktopStationVideoConguration
● Vingtor-Stentofon IP Desktop Video Station - item no. 1408001635
The camera of the Turbine Video station has to be set in the video display part of the Vingtor-
Stentofon desktop station. This is done by logging into video part of the desktop station interface.
● Tapping anywhere on the LCD touchscreen will show the IP address of the video display part.
●Enter the Video-IP address as shown above (e.g. 192.168.45.45) in a web browser to log into
the video part of the desktop station.
To log into the video part of the station:
1. Enter the default User name: admin
2. Enter the default password: alphaadmin

17
Turbine IP Video Station Conguration Guide
A100K11559
● Click Cameras
● Enter values for the parameters as shown
Camera Types
● Camera Type is TCIV with URL :8090/mjpg/video.mjpg
L‘8090’ is the default port number for the camera set in section “5.4.1 Video Settings for Desktop Station”
Camera Allocation
AlphaCom Node Number: Node number of network (e.g. 3)
AlphaCom Directory Number: Directory number of TCIV (e.g. 2222 as set in Main Settings)
Camera IP: IP address of TCIV (e.g. 10.5.101.46)
Camera Type: TCIV
● Click Submit settings

18
A100K11559
Turbine IP Video Station Conguration Guide
6 SIPConguration
The STENTOFON SIP Stations are custom-made IP intercom stations that can integrate with any
iPBX system.
In SIP mode, the Turbine Video stations have been tested for use with the following video display
phones:
● IP Desktop Station with Video Display (Item Number: 1408001635)
● ITSV-1 Video Phone (Item Number: 1490001010)
●Cisco CP-9971 Video Phone
● Bria Softphone
LCongurationofthenon-videopartofthestationsuchasSIPandDAKsettingsisdescribedinthe
manual: A100K11335 Turbine Compact IP Station Getting Started for SIP.
Figure 6 SIP Video Intercom System
6.1 Logging into the Station
Access the station by logging into the web interface using a standard web browser:
1. Open a web browser
2. In the browser’s address bar, type the station IP address and press the ENTER key
- The station login page will be displayed.
To log into the station:
1. Click Login
2. Enter the default User name: admin
3. Enter the default password: alphaadmin
The Station Information page will now be displayed, showing the station settings and status.
Turbine TCIV-2 Turbine TCIV-3
Cisco CP-9971 Phone
(uses Cisco CallManager)
Bria Softphone
iPBX (SIP Domain)
IP Network
IP Desktop Video Display Station
ITSV-1 Video Phone

19
Turbine IP Video Station Conguration Guide
A100K11559
6.2 Station Main Settings
● Click Station Main > Main Settings to access the page for conguring station mode and IP
parameters.
Station Mode
● Select the Use SIP radio-button
Product Model And Accessory
●Model
Select one of the options from the drop-down box :
-VideoNormal(TCIV-2,TCIV-3)
-VideoScrollingStation(TCIV-6)
IP Settings
●Static IP – Select this option if the IP station shall use a static IP address. Enter values for:
-IP-address:IPaddressof TCIV (e.g. 10.5.101.46)
-Subnet-mask:Entersubnetmask
-Gateway: Enter Gateway IP address
-DNS Server 1 (option for network administration)
-DNS Server 2 (option for network administration)
-Hostname (option for network administration)
Read IP Address
● Check the Read IP Address box to enable an unregistered station to speak the IP address
when the call button is pressed.
● Click Save followed by Apply to apply the new conguration settings.

20
A100K11559
Turbine IP Video Station Conguration Guide
6.3 SIPCongurationforITSV-1VideoPhone
● Vingtor-Stentofon ITSV-1 Video Phone - item no. 1490001010
6.3.1 SIPSettingsforITSV-1
● Select SIPConguration > SIP Settings
Account Settings
DirectoryNumber(SIPID):Directory number of Turbine Video station
ServerDomain(SIP):IP address of the SIP Server
LThe values for both these parameters are determined by the system administrator in the SIP server
domain.
● Enter values for the other parameters under Account Settings and Call Settings
● Click Save