Vinotemp B/D-7 User manual

Assembly Instructions for
7ft B/D Module.
B/D-7
Fasteners.
Tools Needed:
(I) Hammer
(I) Power drill
(I) Level
*Suggested 18
guage Brad Gun
with 1-1/4 brad
nails will make
install easier.
Parts
List:
(6) 2-1/2” Phillps
screws for attaching
to wall.
(3) 1-1/4” Joining
Screws to attach to
other modules.
(56) 1-1/4” Shelf
screws.
(30) Nails
(8) Drywall Inserts

(1)
Left End
Ladder
84”
(1)
Middle
Ladders
84”
(1)
Right End
Ladders
84”
Diagram of 1 x 2 Front
Trim in the “up” position
(1) 1 x 2 Front Trim
Assembly Instructions
for 7ft B/D Module.
(5) 1 x 2 Trim (2) for front (3) for back 32-3//16”
(14) Pre-assembled shelves 15”
(12) Pre-assembled diagonals 18-15/16”
B/D-7

Middle Ladder
Pre-
assembled
Shelf
Right End
Ladder
Step 1
Step 1: (Attaching middle shelf
to right end ladder and middle
ladder)
Arrange the right end ladder and
the middle ladder making sure
the set back on the rungs are
facing forward. Place one pre-
assembled shelf on the fourth
rung. The front of the shelf has
a 1 x 1 trim piece fastened uner
the 1 x 2 cross support. From the
inside, either brad nail or screw
the shelves onto the rung in two
places.
Middle
Ladder
Pre-
assembled
Shelf
Right End
Ladder
Step 2
Step 2: (Attaching remaining
shelves to right end ladder)
Place the other six shelves onto
the remaining six rungs and
attach in the same way as Step
1. Make sure the shelves with the
trim pieces are facing the front.
Middle Ladder
Pre-
assembled
Shelf
Right End
Ladder
Left End
Ladder
Step 3
Step 3: (Attaching middle shelf to
left end ladder and middle ladder)
Take the left end ladder and
move it into place on the left side
in the same way as the right end
ladder. Place one pre-assembled
shelf on the fourth rung. The front
of the shelf has a 1 x 1 trim piece
fastened under the 1 x 2 cross
support. From the inside, either
brad nail or screw the shelves
onto the rung in two places.
Middle Ladder
Left End
Ladder
Pre-
assembled
Shelf
Right End
Ladder
Step 4
Step 4: (Attaching remaining
shelves to end ladder and middle
ladder)
Place the other six shelves onto
the remaining six rungs and
attach in the same way as in
Step 1. Make sure the shelves
with the trim pieces are facing the
front.
B/D-7

Middle Ladder
Left End
Ladder
Pre-
assembled
Shelf
Right End
Ladder
1 x 2 Trim
Step 5
Step 5: (Attaching 1 x 2 trim to
front of rack)
Use two of the 1 x 2 x 2 4-1/2”
trim pieces and attach them
to the top and bottom. Both of
these should be places so the
remaining trim is up.
Middle Ladder
1 x 2 Trim
Right
End
Ladder
Pre-
assembled
Shelf
Left End
Ladder
Step 6
Step 6: ( Attaching 1 x 2 trim to
back of rack)
Take the last three 1 x 2 x 2
4-1/2” trim pieces and attach
them to the 1st, 5th and 8th shelf
from the bottom to the top. All
of these should be placed so
the remaining trim is up. The
exposed area of the trim will be
used to screw through to apply
the rack to the wall.
Diagonals
1 x 2 Trim
Left End
Ladder
Pre-
assembled
Shelf
Right End
Ladder
Step 7
Step 7: (Inserting diagonals)
Take all eight pre-assembled
diagonals and insert them into
the eight openings.
Step 8
Step 8: (Finish)
Fasten to the wall through the
back supports using 2-1/2”
screws.
B/D-7

Fastener Placement Guide
A2
Closeup A2
B
A1
B
A1
A
B
(56) shelf
screws
—Place
shelf on
1 x 1’s
and screw
through 1 x
1’s from the
side.
(30) nails
—Nail one
at every
point where
the front and
back trim
intersect a
ladder as
shown.
B/D-7