Viozon 3L Pro User manual

6MM
5MM
As the picture shows,
install VESA mount on
monitor. Be careful to
leave the slide clip
upwards.
VESA standard:
75*75mm ; 100*100mm
STEP3. ATTACH MONITOR/LAPTOP PLATE TO ARM
A
Insert the VESA
connector into the
groove, when heard a
click sound means done.
Note: If you want to remove
the device, please press
shrapnel (A) to remove the
device Up to extract.
INSTALLING MONITOR
INSTALLING LAPTOP PLATE
Insert the Laptop Plate into the
groove, when heard a click
sound means done.
STEP1. ATTACH MOUNT TO WORK SURFACE
≥0.6” - ≤2.36”
3.15”
Install on open edge of
work surface:
Slide the Base Stem against
work surface edge and fully
tighten clamp Screw(A).
A
STEP2. ATTACH ARM TO THE POLE
Remove the screw from the
Forearm by the hex wrench.
Remove the plastic cover
from rear arm.
As the picture shows, install
screw in order, then put
plastic cover back.
Note: Please fix the inside nut of
post(B) in position before tighten
Screw(A) on the clip.
A
B
Remove the screw from the
adapter by the hex wrench.
4
As the picture shows, put the
accessories at the arm,tighten
the screw.
5
As the picture shows, install clip spring arm clip
arm post cap in order.
6
Note: Open cable clip two sides.
Remove cable clip (A) from
the arm, thread cables, install
cable clip on the arm again.
A
STEP4. CABLE MANAGEMENT
Slide the plastic cover on the rear arm upwards until it
disengages. Put cables onto the plastic cover inside. Slide
the cover downwards until it click into place.
Make sure to read the manual before installation and fully
understand how to install, if you have any questions, please
visit our website or contact our service email for the help.
Please make sure the desktop could bear the weight of
mount and monitor before installation.
This product contains small parts, keep these away from
children.
WARNING

X 1
Adaptor
X 1
Base Stem
X 1
Arm
Scan QR code below for
more products from viozon
Pro
X 1
Rear Arm
X 1
Forearm
X 1
Laptop Plate
X 2
VESA Connector
X 2
Clip
X 1
Post Cap
4 / 5 / 6mm
Hex Key
X 10
Screws(M4)
X 10
Screws(M5)
INSTALLATION HARDWARE
WARRANTY SERVICE
FEEDBACK
Never worried when you choose viozon products
We offer the best after-sale service to our customer,
it only takes few minutes.
And then you will get complete service such as installation
guide, technical support, new product reminder, privilege of
purchasing similar products, promotions and warranty service
from Viozon.
Viozon is focusing on high-standard products, we believe
that customers’ feedback drives us upgrading products.
Writing a review which sharing your experience will help
other customers. Also, your review will give us great
encouragement and confidence for future improvement. If
you have any questions, please feel free to contact us
without hesitation.
Share it?
Let us know with a customer review.
Just send you name and order number to
[email protected]
Facebook: Viozon [email protected]
FOR HELP PLEASE CONTACT US:
www.vio-zon.com Scan QR code
to get install video
If you feel the pitching angle too tight or too loose when
adjusting the mount, please adjust the Screw.
The load weight of mount is 3.3 to 19.8lb, factory default
settings: 6.6 to 8.8lb, it will decrease gradually when
adjusting the Screw(C) by clockwise rotation, vice versa.
Place your hand on forearm
and push it hard downwards.
Note: Once you feel the damping of
screw increases or cannot be
rotated, please stop it avoid of
damaging the mount.
TENSION ADJUSTMENT
WEIGHT ADJUSTMENT
ADJUST SPRING ARM AT
VERTICAL DIRECTION
6MM
5MM
5MM
ARM ADJUSTMENTS