Vision VN6XEHi-Standard D1 Manual

Page 1/ 14
HARDWARE INSTALLATION GUIDE
VN6XEHi-Standard D1 Outdoor IR Bullet IP Camera
VN6XSMi - 1.3 Megapixel Outdoor IR Bullet IP Camera
VN6XSM3Ti-3 Megapixel Outdoor IR Bullet IP Camera
Version 1. 0. 0
Released on 2nd of July., 2012
Vision Hitech Co., Ltd.

Page 2/ 14
PRECAUTIONS
By selecting this product, you have decided to use a professional device that guarantees highest quality and
reliability. We would like to thank you very much for your confidence and kindly ask you to read the following
instructions carefully before installation and operation in order to take full advantage of all quality features
regarding this product.
The lighting flash with an arrowhead symbol, within an equilateral triangle is intended to alert
the user to the presence of non-insulated dangerous voltage within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at its own
expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
CAUTION –To prevent electric shock and risk of the fire hazards
-Do NOT use power source other than that specified.
-Do NOT expose this appliance to rain or moisture.
Trademarks
All names used in this manual for hardware and software are probably registered trademarks of respective
companies.
This installation should be made by a qualified service person and should conform to all local codes.
Table of content

Page 3/ 14
Hardware Installation Guide
1. Precautions ---------------------------------------------------------------------------------------------------- 4
2. Limitation of liability ---------------------------------------------------------------------------------------- 4
3. Disclaimer of warranty ------------------------------------------------------------------------------------- 4
4. Package Contents --------------------------------------------------------------------------------------------- 5
5. Cable Connection --------------------------------------------------------------------------------------------- 6
6. Installation -------------------------------------------------------------------------------------------- 7~9
7. Dimension (mm) ----------------------------------------------------------------------------------------------- 10
8. Specification ------------------------------------------------------------------------------------------------ 11~12
8-1 VN6XEHi ---------------------- ------------------------------------------------------------------------------------------- 11

Page 4/ 14
1. Precautions
Please read the manual carefully before the installation in order to set up the camera correctly and to
obtain the best picture quality.
Please keep the manual in good condition for your future reference and service application.
Installation and services should be only carried out by an authorized personnel according to local safety
regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera from power supply
and have it checked by your authorized dealer before reusing.
Avoid installing the camera at extremely hot or cold places.
If you are not a certified person, never try to dismantle the camera. To avoid electric shock, never remove
the screws or covers. There are no parts inside that need maintenance by the user. All maintenance should
be carried out by qualified personnel.
Avoid installing the camera at a place of high humidity.
Avoid installing the camera at the place exposed to gas or oil.
Keep the top glass of the lens always clean in order to obtain the best picture quality all the time. Be
careful not to be stained by fingerprint.
Don't face the camera directly toward sunlight or sunlight reflecting area. CCD may go defective at this
condition.
Please give a special attention to keep the unit from dangerous drop or external shock during the process
of transportation or handling.
Never try to touch the camera in wet hand. It may cause an electric shock.
Do not expose the camera to radioactivity. It causes a serious damage on the CCD.
2. Limitation of liability
This publication is provided “AS IS” without warranty of any kind, either express or implied, including but not
limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of
the third party's right. This publication could include technical inaccuracies or typographical errors. Changes
are added to the information herein, at any time, for the improvements of this publication and/or the
corresponding product(s).
3. Disclaimer of warranty
In no event shall seller be liable to any party or any person, except for replacement or reasonable maintenance
of the product, for the cases, including but not limited to below:
(1) Any damage and loss, including without limitation, direct or indirect, special, consequential or exemplary,
arising out of or relating to the product;

Page 5/ 14
(2) Personal injury or any damage caused by inappropriate use or negligent operation of the user;
(3) Unauthorized disassemble, repair or modification of the product by the user;
(4) Inconvenience or any loss arising when images are not displayed, due to any reason or cause including any
failure or problem of the product;
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the system combined by the
devices of third party.
(6) Any claim or action for damages, brought by any person or organization being photogenic subject, due to
violation of privacy with the result of that surveillance-camera's picture, including saved data, for some
reason, becomes public or is used for the purpose other than surveillance.
4. Package Contents
Hardware Installation
Guide x 1
IP Camera x 1
DC12V/1.5A
(Option) x 1
Tapping screws x 4
Plastic anchor x 4
External Video
Cable(VN6xEHi) x 1
Crossover LAN
Cable x 1
x
L-Wrench (3.0mm) x 1
CD
- Hardware Installation Guide (PDF)
- IP Camera Manual (PDF)
- NVR Pro Manual
- NVR Lite (16Ch) Program
- IPScan Utility Program (IP Installer)

Page 6/ 14
5. Cable Connection
This IP camera uses 12VDC for power source. Please make sure to use a UL/CE approved and 12VDC regulated
power supply for input power.
●Alarm In/out Cable
COLOR
DESCRIPTION
Sky Blue/Black
GND
Sky Blue
ALARM INPUT 1
Violet
ALARM OUT
Violet/White
COM
Power Connector (DC12V)
Network Connector
Analog Video Out(YELLOW)
Sensor In/Alarm Out
Audio-in (RED)
Audio-out (WHITE)

Page 7/ 14
6. Installation
■How to mount to ceiling / wall
①Drill three screw holes on the wall plate to fix three plastic anchors (supplied) in the holes.
②Fix the plastic anchors in the holes.
③Position the mounting bracket on the screw points.
④Fix the mounting bracket by tightening the screws.
⑤Slightly loosen bolt (A) then adjust tilt(180˚) and rotation(360˚) of the camera using a serration
on the bracket and tighten the bolt firmly.
⑥Slightly loosen bolt (B) then adjust pan(360˚) of the camera and tighten the bolt firmly.

Page 8/ 14
■Axis Adjustment
■Lens external adjustment, EXT-Video
Zoom & Focus External Adjustment with Lens Dial (Patent pending)
■OSD Manual for functions control
- How to use tactile switch on the OSD control
Push –to enter the menu or to save settings.
Push up or down –select functions.or zoom control
Push left or right –to adjust levels or focus control
① Pan 360˚
Slightly loosen Pan bolt, then adjust pan of the
camera using a serration on the bracket and
tighten the bolt firmly again
②Tilt 180˚
Slightly loosen Tilt bolt, then adjust tilt of the
camera using a serration on the
bracket and tighten the bolt firmly again
③ Rotation 360˚
Slightly loosen Tilt bolt then adjust rotation
of the camera using a serration on the
bracket and tighten the bolt firmly again
- How to use EXT-video
①Turn open the OSD cap counterclockwise.
OSD cap is designed to be hanging from the
camera even after opening it.
②Connect Extra video output connector
(A) to camera tester or local monitor as shown in
the above. Then, control the lens by using
Zoom & Focus dial.

Page 9/ 14
- OSD MENU(VN6XEHi)

Page 10 / 14
7. Dimension (mm)

Page 11 / 14
8. Specification
8.1. VN6XEHi
Classification
Specification
General
CPU
32-bit ARM9 RISC CPU up to 533MHz, 32KB I/D-Cache, MMU
Video Buffer
16Mbyte Video Frame Buffer
Flash
16 Mbyte Flash Memory
SDRAM
256Mbyte
Image
Pickup
Image sensor
1/3" Sony 960H Ex-view HAD CCDⅡ
Effective Pixels
NTSC : 976(H) x 494(V), PAL : 976(H) x 582(V)
H. Resolution
650TV Lines(Color)/ 700TV Lines(B/W)
Synchronizing system
Internal
Scanning system
NTSC : 525 Lines PAL : 625 Lines 2:1 Interlaced
S/N Ratio
More than 52dB (AGC Off)
Min. Illumination
0Lux (IR On)
Shutter Speed
NTSC:1/60~1/100,000 sec. PAL:1/50~1/100,000 sec.
Gamma Correction
Standard γ = 0.45
Lens
2.8-12mm Motorized zoom lens
Video
Video compression
H.264 baseline profile, Motion JPEG
Resolutions
Up to D1(NTSC:720X480, PAL:720X576)
Frame rate
H.264 Up to 30fps at D1
MJPEG Up to 30fps at D1
Video streaming
Support multi stream with H.264, MJPEG
Adjustable frame rate
VBR/CBR in H.264
Pan/Tilt/Zoom
Digital PTZ
Image setting
Day & Night
Auto White Balance
Auto Exposure
Effect - Color, Sharpness, Mirror/V-Flip, etc.
BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC/PAL
Privacy Mask
Effect - Color, Sharpness, Mirror/V-Flip, etc.
Output
BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC/PAL
Audio
Audio streaming
Two-way, full duplex
Audio compression
G.711
Sample Rate
8KHZ
Data Rate
64Kbps
Audio input
Microphone input /1 x Line-In (Mono)
Audio output
Line output/ 1 x Line-Out (Mono)
Network
Security
Password protection
User access log
HTTPS encryption
Supported protocol
HTTP, HTTPS, FTP, SMTP, UPnP, DNS, DynDNS, NTP
RTSP, RTP, TCP, UDP, ICMP, DHCP
System
integration
Intelligent video
Motion detection up to 1280x720 with 32x24 blocks
Alarm trigger
Motion detection
External input/Normal Open/Close Type

Page 12 / 14
Alarm events
File upload via ftp, e-mail
Notification via email, FTP and TCP
Video buffer
16MB pre-alarm and post-alarm
Recording
Save to Micro SD card with event mode and continuous mode
Firmware upgrade
Remote upgrade via network
API
CGI Interface document
ActiveX Interface(ocx(dll) + document)
Physical
RESET Button
1 x Factory Reset Button
Power Source
DC 12V/1.5A, PoE(Power over Ethernet): 802.3af(Option)
Power Consumption
Max. 5.5W
Max. 7.2W with IR On
Net Weight
520g Appr.(Camera Only)
LED's
Power, Network Connection
Dimension
87.7mm(W) X 108.7mm(H) X 297mm(D) including Bracket
Environment
Operating Temperature
-25 degree~50 degree Celsius (-13F~122F)
Storage Temperature
-25 degree~60 degree Celsius (-13F~140F)
Software
Included Software
NVR Lite (16 Channel), IP Installer (Windows Only)
Package
Package Contents
Network Camera, Use Manual, External Power Adaptor, Software
CD
8.2.VN6XSMi
Classification
Specification
General
CPU
32-bit ARM9 RISC CPU up to 533MHz, 32KB I/D-Cache, MMU
Video Buffer
16Mbyte Video Frame Buffer
Flash
16 Mbyte Flash Memory
SDRAM
256Mbyte
Image
Pickup
Image sensor
1.3 Megapixel 1/3" SONY progressive scan CMOS image sensor
Total Pixels
1384(H) x 1076(V) 1.49 Megapixel
Effective Pixels
1329(H) x 1049(V) 1.39 Megapixel
S/N Ratio
More than 50dB
Min. Illumination
0Lux (IR On)
IR Distance
30M
Day & Night
ICR
Lens
3.7mm Mega Pixel Board Lens
Video
Video compression
H.264 baseline profile, Motion JPEG
Resolutions
Up to 1280 x 720
Frame rate
H.264 Up to 30fps with 1280x720
MJPEG Up to 30fps with VGA resolution
Video streaming
Support multi stream with H.264, MJPEG
Adjustable frame rate
VBR/CBR in H.264
Pan/Tilt/Zoom
Digital PTZ
Image setting
Day & Night
Auto White Balance
Auto Exposure
Effect - Color, Sharpness, Mirror/V-Flip, etc.
BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC/PAL
Privacy Mask
Effect - Color, Sharpness, Mirror/V-Flip, etc.
Output
BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC/PAL
Audio
Audio streaming
Two-way, full duplex

Page 13 / 14
Audio compression
G.711
Sample Rate
8KHZ
Data Rate
64Kbps
Audio input
Microphone input /1 x Line-In (Mono)
Audio output
Line output/ 1 x Line-Out (Mono)
Network
Security
Password protection
User access log
HTTPS encryption
Supported protocol
HTTP, HTTPS, FTP, SMTP, UPnP, DNS, DynDNS, NTP
RTSP, RTP, TCP, UDP, ICMP, DHCP
System
integration
Intelligent video
Motion detection up to 1280x720 with 32x24 blocks
Alarm trigger
Motion detection
External input/Normal Open/Close Type
Alarm events
File upload via ftp, e-mail
Notification via email, FTP and TCP
Video buffer
16MB pre-alarm and post-alarm
Recording
Save to Micro SD card with event mode and continuous mode
Firmware upgrade
Remote upgrade via network
API
CGI Interface document
ActiveX Interface(ocx(dll) + document)
Physical
RESET Button
1 x Factory Reset Button
Power Source
DC 12V/1.5A, PoE(Power over Ethernet): 802.3af(Option)
Power Consumption
Max. 5.5W
Max. 5.5W
Net Weight
520g Appr.(Camera Only)
LED's
Power, Network Connection
Dimension
87.7mm(W) X 108.7mm(H) X 297mm(D) including Bracket
Environment
Operating Temperature
-25 degree~50 degree Celsius (-13F~122F)
Storage Temperature
-25 degree~60 degree Celsius (-13F~140F)
Software
Included Software
NVR Lite (16 Channel), IP Installer (Windows Only)
Package
Package Contents
Network Camera, Use Manual, External Power Adaptor, Software
CD
8.3.VN6XSM3Ti
Classification
Specification
General
CPU
32-bit ARM9 RISC CPU up to 533MHz, 32KB I/D-Cache, MMU
Video Buffer
16Mbyte Video Frame Buffer
Flash
16 Mbyte Flash Memory
SDRAM
256Mbyte
Image
Pickup
Image sensor
3.0 Megapixel 1/2.8" SONY progressive scan CMOS image sensor
Total Pixels
2144(H) x 1588(V) 3.4 Megapixel
Effective Pixels
2096(H) x 1561(V) 3.27 Megapixel
S/N Ratio
More than 50dB
Min. Illumination
0Lux (IR On)
IR Distance
30M
Day & Night
ICR
Lens Control
Motorized Lens Control
Lens
3~10mm Vari-focal Auto Iris Megapixel Lens
Video
Video compression
H.264 High profile, Motion JPEG

Page 14 / 14
Resolutions
Up to 2048 x 1536
Frame rate
H.264 Up to 15fps with 2048x1536
MJPEG Up to 30fps with 1080p resolution
Video streaming
Support multi stream with H.264, MJPEG
Adjustable frame rate
VBR/CBR in H.264
Pan/Tilt/Zoom
Digital PTZ
Image setting
Day & Night
Auto White Balance
Auto Exposure
Privacy Mask
Effect - Color, Sharpness, Mirror/V-Flip, etc.
Output
BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC/PAL
Audio
(Option)
Audio streaming
Two-way, full duplex
Audio compression
G.711
Sample Rate
8KHZ
Data Rate
64Kbps
Audio input
Microphone input /1 x Line-In (Mono)
Audio output
Line output/ 1 x Line-Out (Mono)
Serial
Port1
RS-485
Data Rate
600bps~ 115200bps
Network
Security
Password protection
User access log
HTTPS encryption
Supported protocol
HTTP, HTTPS, FTP, SMTP, UPnP, DNS, DynDNS, NTP
RTSP, RTP, TCP, UDP, ICMP, DHCP
System
integration
Intelligent video
Motion detection up to 2048x1536 with 32x24 blocks
Alarm trigger
Motion detection
External input/Normal Open/Close Type
Alarm events
File upload via ftp, e-mail
Notification via email, FTP and TCP
Video buffer
16MB pre-alarm and post-alarm
Firmware upgrade
Remote upgrade via network
API
CGI Interface document
ActiveX Interface(ocx(dll) + document)
Physical
Power Source
1 x Factory Reset Button
Power Consumption
DC 12V/1.5A, PoE(Power over Ethernet): 802.3af(Option)
Net Weight
Max. 5.5W
LED's
520g Appr.(Camera Only)
Dimension
Power, Network Connection
Environment
Operating
Temperature
87.7mm(W) X 108.7mm(H) X 297mm(D) including Bracket
Storage Temperature
-25 degree~50 degree Celsius (-13F~122F)
Software
Included Software
-25 degree~60 degree Celsius (-13F~140F)
Package
Package Contents
NVR Lite (16 Channel), IP Installer (Windows Only)