VisionX VX Series Manual

VISIONXLIGHTING.COM
Installation Instructions & User’s Manual

VISION X
About The VX SERIES 7” HEADLIGHT
FEATURES
1. LED Halo
2. DOT approved
3. Multiple wiring connections available
VX SERIES 7” HEADLIGHT SPECIFICATIONS
1. Warranty : Extended
2. Amp Draw : High 3.0A/ Low 2.2A/ Halo 0.33A @12V
3. Input Voltage : 9-32V
4. Beam Patterns : High, Low, Halo
5. LED Lifespan : 50,000 Hours
PREPARATION
1. We recommend completely reading instructions before
installing.
2. Consult your local state regulatory agency regarding the
use of LED lighting.
3. The placement of LED lighting should not restrict airow to
the radiator, or block head lamps, turn signals, or parking
lights.
MAINTENANCE
1. All Vision X models have been designed for
maintenance free use. In the case an LED lamp or other
part replacement is needed please contact your authorized
service center.

VX SERIES LED HEADLIGHT
1
Qty: 2
7” Headlight
XIL-7RD
WARNINGS
As with many other high-tech products, this VISION X LED
requires a bit of attention before you can use it. Please read
the accompanying information carefully rst.
1. Don’t stare directly into the light or shine directly into the
eyes of another person as this may cause temporary loss
of vision.
2. Never disassemble the products, as all parts must be
factory serviced to insure proper operation.
3. Don’t interchange the parts inside this light with other
products.
4. The LED light is to be mounted on the vehicle only in a
vertical, bottom mounting, or in a suspended position.
5. After turning on the light, the body might be hot enough
to warrant a burn risk. Be careful when you touch the
body after turning on the light for a long period of time.
6. Use the supplied wire harness for electrical installation.
7. The LED light must not adversely a󰀨ect the performance
of low beam, high beam, engine cooling or the driver’s
view.
1
Qty: 2
7” Headlight
XIL-7RD
2
Qty: 2
H4 Plug
P-HLH42H13
XIL-7RDKITJK
XIL-7RDKIT

VISION X
Gore-Tex
Cap (ON)
REMOVE
Gore-Tex
Cap (OFF)
Having a correct venting solution in place can impact
the lamps longevity and durability. The Gore-Tex valve
equalizes pressure bi-directionally and manages moisture all
while providing spray, immersion, and splash protection in the
event the valve is exposed to the elements.
GORE-TEX VALVE
Figure 1

VX SERIES LED HEADLIGHT
SEE VEHICLE OWNERS MANUAL FOR HELP REPLACING HEADLIGHT
ADDITIONAL WIRING HARNESS ADAPTER MAY BE NEEDED CONSULT
YOUR DEALER TO DETERMINE IF ONE IS NEEDED
1. Disconnect vehicle battery prior to installation.
2. Review your vehicle manual for detailed instructions for
removing existing factory head light housing.
3. Remove Gore-Tex Valve Cover, prior to installation see
[Figure 1]
4. Attach VX Series LED Headlight to Optional HI-4 Module
(P–HLHI4), then to the existing factory plug and re-install
according to your vehicles manual. See [Figure 2]
5. To wire the LED Halo Daytime Running light, locate the
white wire on the back of the light. Power the white wire by
attaching it to the accessory power of the vehicle. If there
isn’t accessory power available a󰀩x it to the blue wire of
the light or its own aux switch.
WIRING INSTRUCTIONS XIL-7RDKIT
WIRING DIAGRAM
Red = High Beam [ + ]
Blue = Low Beam [ + ]
Black = Ground [ - ]
White = Halo [ + ]
WIRING KEY
white
black
blue
red
H4
Plug
OPTIONAL
P-HLHI4
Figure 2

VISION X
WIRING DIAGRAM
Red = High Beam [ + ]
Blue = Low Beam [ + ]
Black = Ground [ - ]
White = Halo [ + ]
WIRING KEY
1. Disconnect vehicle battery prior to installation
2. Review your vehicle manual for detailed instructions for
removing existing factory head light housing.
3. Remove Gore-Tex Valve Cover, prior to installation see
[Figure 1]
4. Attach VX Series LED Headlight to Optional JEEP JK HI-4
Module (P–HLHI4H13), then to the existing factory plug and
re-install according to your vehicles manual. See [Figure 3]
5. To wire the LED Halo Daytime Running light, locate the
white wire on the back of the light. Power the white wire by
attaching it to the accessory power of the vehicle. If there
isn’t accessory power available a󰀩x it to the blue wire of the
light or its own Aux switch.
white
black
blue
red
H13
Plug
OPTIONAL
P-HLHI4H13
WIRING INSTRUCTIONS XIL-7RDKITJK
SEE VEHICLE OWNERS MANUAL FOR HELP REPLACING HEADLIGHT
ADDITIONAL WIRING HARNESS ADAPTER MAY BE NEEDED CONSULT
YOUR DEALER TO DETERMINE IF ONE IS NEEDED
Figure 3

VX SERIES LED HEADLIGHT
TIP: For complete application guide see web site
STEP 1: Low Beam
STEP 2: Center line of Low Beam
STEP 3: High Beam
2
1
3
TESTING THE LIGHT
1. After all connections have been made start your vehicle
and test your switch to make sure it turns on the light prior
to reassembly.
2. Make sure the angle of your light is correct, otherwise
adjust the light angle again.
3. Make sure no wire or other components of the harness are
exposed to water spray, excessive heat, or moving parts.
P-HLHI4- High Low High 4 adapter engages all three beam
modes simultaneously to dramatically increase visibility and
output.
P-HLHI4H13- High Low High 4 adapter engages all three
beam modes simultaneously to dramatically increase visibility
and output. (For use with XIL-7RDKITJK With H13 Plug)
P-HLCBAH13- Single Canbus Integration adapter levels
electrical current to remove electrical interference from the
vehicle and eliminate ickering in light.(For use with non
XIL-7RDKITJK part #’s)
Halo LowHigh HLHI4
HEAD LIGHT ALIGNMENT
ADAPTERS/ACCESSORIES

VISIONXLIGHTING.COM
You May Also Be Interested In:
SECURITY NUT
Available in multiple sizes
SECURITY BOLT
Available in multiple sizes
Jeep A-Pillar
Part # - 9888392
Item # -XIL-OEA0713JKCPZ1
Part # - 4000308
Item # - XIL-LICENSEP
License Plate Bracket for Lights
up to 20”
Part # - 9892320
Item # - XIL-WINCH10
Light Bar Winch Fairlead
10” Bracket
(Available in 6”)