Vista 2500 User manual

IN GROUND INSTALLATION POUR CONCRETE INSTALLATION
INSTALLATION INSTRUCTIONS FOR 12 VOLT
BOLLARD
MODEL #2500
FOR USE ONLY WITH LOW VOLTAGE LANDSCAPE POWER UNITS THAT DO NOT
EXCEED 25 AMPS, 15 VOLT MAX.
WARNING: Bollard luminaires must be installed in accordance with
the National Electrical Code (NEC) and local codes. Failure to do so
will void the warranty and may result in serious injury and/or damage to the bollard luminaire.
SAFETY WARNING: Luminaire can become very hot depending on lamp wattage used.
Lens and metal around lamp can become hot enough to blister hands. Particular care
should be taken not to locate luminaires where small children can reach them if high wattage lamps are used.
LUMINAIRES ARE NOT TO BE INSTALLED WITHIN 10 FT. (3.05M) OF A
POOL OR SPA. SECONDARY CABLE IS NOT TO BE BURIED MORE THAN
6". WHEN USING MULTIPLE LUMINAIRES, LOAD IS NOT TO EXCEED
TOTAL WATTS OF TRANSFORMER RATING. DO NOT USE EXTENSION
CORDS ON POWER UNITS.
NOTE: Always use UL recognized wire connectors for connections.
NOTE: Save these instructions for future reference.
BOLLARD IS UL LISTED FOR ABOVE GROUND INSTALLATION ONLY.
TOOLS REQUIRED FOR INSTALLATION:
Flat head screwdriver Shovel Wire strippers Cement concrete (if pour concrete method chosen)
INSTRUCTIONS FOR STAKE MOUNT INSTALLATION
NOTE: Your Vista 12 volt Bollards are shipped with a ground stake to facilitate a stake mount
installation. However, for a permanent and secure installation a concrete footing
support for the bollard base is recommended.
1. To prevent electrical shock, disconnect transformer from electrical supply before installation
or service.
2. Dig a hole at selected location.
3. Using the 1/2" threaded short nipple (provided), attach ground stake to center hole in
bollard base and insert stake with base into the ground until bottom of base is even with grade.
Base Set Screw
Post
Lens Set Screw
Lens
Base
Grade
Concrete
Lens
Post
Base Set Screw
Base
Grade
Lens Set Screw

4. Run wire pigtail through bottom hole of base and strip the two (2) leads from the
bollard wire. Using the two (2) silicone filled safety connectors (provided), connect the leads
from the bollard to the main supply cable leads.
NOTE: Luminaires are supplied with 36" of 18-2 cable pigtail for secure connection to the main
supply cable. The wire is to be protected by routing in close proximity to the luminaire.
The wiring shall be buried a maximum of 6 inches (15.2 cm) in order to connect the
main supply cable.
5. Slip bollard over base and tighten set screws.
6. Provide power to the luminaire and check for proper operation.
INSTRUCTIONS FOR POUR CONCRETE INSTALLATION
1. To prevent electrical shock, disconnect transformer from electrical supply before installation
or service.
2. Dig a hole at selected location.
3. Using the 1/2" threaded short nipple (provided), attach ground stake to center hole in
bollard base and insert stake with base into the ground until bottom of base is even with grade.
4. Run wire pigtail through bottom hole of base and strip the two (2) leads from the
bollard wire. Using the two (2) silicone filled safety connectors (provided), connect the leads
from the bollard to the main supply cable leads.
NOTE: Luminaires are supplied with 36" of 18-2 cable pigtail for secure connection to the main
supply cable. The wire is to be protected by routing in close proximity to the luminaire.
The wiring shall be buried a maximum of 6 inches (15.2 cm) in order to connect the
main supply cable.
5. Pour concrete at least 2" thick.
6. Slip bollard over base and tighten set screws.
7. Provide power to the luminaire and check for proper operation.
IMPORTANT SAFETY INSTRUCTIONS
LIGHTED LAMP IS HOT!!
WARNING: TO REDUCE THE RISK OF FIRE, OR INJURY TO PERSONS:
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamps get hot quickly! Contact only switch/plug when turning on.
3. Do not touch hot lens, guard or enclosure.
4. Keep lamp away from material that may burn.
5. Do not touch the lamp at any time. Use a soft cloth. Oil from
the skin may damage lamp.
6. Do not operate luminaire fitting with a missing or damaged cover.
LAMP INSTALLATION/REPLACEMENT:
CAUTION: Do not exceed maximum wattage marked on luminaire
label.
1. To prevent electrical shock, disconnect transformer from electrical supply before
service.
2. Loosen the two (2) base set screws and remove luminaire from base.
3. Replace lamp with correct wattage and type marked on fixture label.
NOTE: DO NOT touch lamp with bare hands. Always use soft cloth or the
plastic wrapping (if available) from the lamp to handle the lamp.
4. Re-install luminaire and tighten the two (2) base set screws.
VISTAPROFESSIONALOUTDOORLIGHTING DivisionofU.S.T.E.Inc. Website:www.vistapro.com
1625 SurveyorAvenue,SimiValley,CA93063 [phone] FAX:[phone] (800)766-847
8